• Journal of the Korean Society for Nondestructive Testing
• /
• v.33 no.4
• /
• pp.323-329
• /
• 2013

This perform research of angle rated defect detection conditions and nuclear power plant piping defect detection by lock-In infrared thermography technique. Defects were processed according to change for wall-thinning length, Circumference orientation angle and wall-thinning depth. In the used equipment IR camera and two halogen lamps, whose full power capacitany is 1 kW, halogen lamps and target pipe's distance fixed 2 m. To analysis of the experimental results ensure for the temperature distribution data, by this data measure for defect length. Reliability of lock-In infrared thermography data is higher than Infrared thermography data. This through research, Shape of angle rated defect is identified industry place. It help various angles defect detection in the nuclear power plant in operation.

• 한국전산유체공학회:학술대회논문집
• /
• 2008.03b
• /
• pp.256-259
• /
• 2008

Ejector system is a device to transport a low-pressure secondary flow by using a high-pressure primary flow. Ejector system is, in general, composed of a primary nozzle, a mixing section, a casing part for suction of secondary flow and a diffuser. It can induce the secondary flow or affect the secondary chamber pressure by both shear stress and pressure drop which are generated in the primary jet boundary. Ejector system is simple in construction and has no moving parts, so it can not only compress and transport a massive capacity of fluid without trouble, but also has little need for maintenance. Ejectors are widely used in a range of applications such as a turbine-based combined-cycle propulsion system and a high altitude test facility for rocket engine, pressure recovery system, desalination plant and ejector ramjet etc. The primary interest of this study is to set up an applicable model and operating conditions for an ejector in the condition of sonic and subsonic, which can be extended to the hydrogen fuel cell vehicle. Experimental and theoretical investigation on the sonic and subsonic ejectors with a converging-diverging diffuser was carried out. Optimization technique and numerical simulation was adopted for an optimal geometry design and satisfying the required performance at design point of ejector for hydrogen recirculation. Also, some ejectors with a various of nozzle throat and mixing chamber diameter were manufactured precisely and tested for the comparison with the calculation results.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.36 no.2
• /
• pp.173-178
• /
• 2012

Currently, active research is being performed on printing of electronic devices such as RFID devices, flexible displays, solar cells, and e-paper. This technique has several advantages over existing technologies such as lithography and etching. In particular, RFID devices, flexible displays, solar cells, and e-paper require flexibility and a mass production system. Thus, attention is being focused on the roll-to-roll process. High quality should be guaranteed in the roll-to-roll printed electronics systems, and good thickness and roughness qualities must be ensured. Experimental design was applied to this problem to analyze the main effects and interaction effects of various factors. Matching technology between the nip roll characteristics and the quality of the print pattern in roll-to-roll printed electronics systems was proposed to improve the printing quality.

• Journal of Korea Multimedia Society
• /
• v.15 no.8
• /
• pp.1017-1030
• /
• 2012

Most watermarking schemes for video contents protection have been studied to increase watermark's robustness and invisibility against such compressions and many kinds of signal processing after embedding copyright information to the original contents. This paper proposes an active watermarking that infect watermark to contents in the video decoding process using embedded infectious watermark and control signals from a video encoder side. To achieve this algorithm, we design a kernel based watermarking in video encoder side that is possible to recover the original contents and watermark in watermark detection procedure perfectly. And then, by reversible de-watermarking in video decoder side, we design the active watermark infection method using detected watermark and control signal. This means that our system can provide secure re-distributions of video contents without any quality degration and watermark bit error against transcoding or re-encoding processing. By experimental results, we confirmed that the embedded watermark was infected by video contents and codec perfectly without any declines of compression ratio and video quality.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.33 no.1
• /
• pp.34-39
• /
• 2013

In the advanced research deducted infrared thermography (IRT) test using 4 inch pipe with artificial wall-thinning defect to measure on the wall-thinned nuclear pipe components. This study conducted for defect detection condition of nuclear small-bore pipe research using deducted condition in the advanced research. Defect process is processed by change for defect length, circumferential direction angle, wall-thinning depth. In the used equipment IR camera and two halogen lamps, whose full power capacitany is 1 kW, halogen lamps and Target pipe experiment performed to the distance of the changed 1 m, 1.5 m, 2 m. To analysis of the experimental results ensure for the temperature distribution data, by this data measure for defect length. artificial defect of 4 inch pipe is high reliability in the 2 m, but small-bore pipe is in the 1.5 m from the defect clearly was detected.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.05a
• /
• pp.680-685
• /
• 2006

This paper describes the aeroelastic stability test of the small-scaled 'Next-Generation Blade(NRSB)' with NRSH (Next-Generation Hub System) and HCTH hingeless hub system in hover and forward flight conditions. Excitation tests of rotor system installed in GSRTS(General Small-scale Rotor Test System) at KARI(Korea Aerospace Research Institute) were tarried out to get lead-lag damping ratio of blades with flexures as hub flexure. MBA(Moving Block Analysis) technique was used for the estimation of lead-lag damping ratio. First, NRSB-1F blades with HCTH hub system, Then NRSB-1F with NRSH hub system were tested. Second, NRSB-2F blades with NRSH hub system were tested. Tests were done on the ground and in the wind tunnel according to the test conditions of hover and forward flight, respectively. Non-rotating natural frequencies, non-rotating damping ratios and rotating natural frequencies were showed similar level fir each cases. Estimated damping ratios of NRSB-1F, NRSB-2F with HCTH and NRSH were above 0.5%, and damping ratio increased by collective pitch angle increasement. Furthermore damping ratios of NRSB-2F were higher than damping ratios of NRSB-1F in high pitch angle. It was confirmed that the blade design for noise reduction would give observable improvement in aeroelastic stability compared to paddle blade and NRSB-1F design.

• Archives of design research
• /
• v.14 no.3
• /
• pp.127-134
• /
• 2001

This study suggests a model of experimental visual artworks with interactive art forms in which 2-D paintings are transformed to interactive 3-D animation works. Multimedia programming was employed to evolve objective still paintings to the animation of computer 3-D images with respect to visual ideas derived from visual components in the still painting and to response to the reactions users. The format and technique of the art works are based upon the contents developed by the author and the research materials are selected from the surrealistic paintings of tile world-famous Belgian painter, Rene Magritte. In the present paper, following topics are discussed in detail: a study of various visual cases occurring in transforming still paintings to animation works containing interactive components; a study of 3-D imaging and image processing techniques to transform 2-D paintings to 3-D images; animation techniques for interaction and overall structuring techniques; multimedia programming and user interface.

• Korean Journal of Computational Design and Engineering
• /
• v.19 no.4
• /
• pp.356-367
• /
• 2014

A robotic sapatial augmented reality (RSAR) system, which combines robotic components with projector-based AR technique, is unique in its ability to expand the user interaction area by dynamically changing the position and orientation of a projector-camera unit (PCU). For a moving PCU mounted on a conventional robotic device, we can compute its extrinsic parameters using a robot kinematics method assuming a link and joint geometry is available. In a RSAR system based on user-created robot (UCR), however, it is difficult to calibrate or measure the geometric configuration, which limits to apply a conventional kinematics method. In this paper, we propose a data-driven kinematics control method for a UCR-based RSAR system. The proposed method utilized a pre-sampled data set of camera calibration acquired at sufficient instances of kinematics configurations in fixed joint domains. Then, the sampled set is compactly represented as a set of B-spline surfaces. The proposed method have merits in two folds. First, it does not require any kinematics model such as a link length or joint orientation. Secondly, the computation is simple since it just evaluates a several polynomials rather than relying on Jacobian computation. We describe the proposed method and demonstrates the results for an experimental RSAR system with a PCU on a simple pan-tilt arm.

• The Transactions of the Korea Information Processing Society
• /
• v.2 no.5
• /
• pp.777-786
• /
• 1995

This paper describes several algorithms for technology mapping of logic functions into interesting and popular FPGAs that use look-up table memories. In order to improve the technology mapping for FPGA, some existing multi-level logic synthesis, decomposition reduction and packing techniques are analyzed and compared. And then new algorithms such as node-pair decomposition, merging fanin, unified reduction and multiple output decomposition which are used for combinational logic design, are proposed. The cost function is used to minimize the number of CLBs and edges of the network. The cost is a linear combination of each weight that is given by user. Finally we compare our new algorithm with previous logic design technique［8］. In an experimental comparison our algorithm requires 10% fewer CLB and nets than SIS-pga.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.36 no.2C
• /
• pp.65-77
• /
• 2011

With the rapid expansion of application fields of vector data model such as CAD design drawing and GIS digital map, the security technique for vector data model has been issued. This paper presents the vector data hashing for the authentication and copy protection of vector data model. The proposed hashing groups polylines in main layers of a vector data model and generates the group coefficients by the line curve curvatures of the first and second type of all poly lines. Then we calculate the feature coefficients by projecting the group coefficients onto the random pattern and generate finally the binary hash from the binarization of the feature coefficients. From experimental results using a number of CAD drawings and GIS digital maps, we verified that the proposed hashing has the robustness against various attacks and the uniqueness and security by the random key.