• Journal of the Korean Society of Safety
• /
• v.32 no.3
• /
• pp.28-33
• /
• 2017

In this study, the composite material of expandable graphite was made to the material development for improving such as a composite material of the sandwich panels or material properties of a fire door and was tested by the ISO 1182, ISO 5660-1(Cone calorimeter Method). For the test, the composite material of expandable graphite, what the expandable graphite ratio was increased by respectively 0g~30g, was classified A1,A2, A3, A4, and made to the test specimens. Through cone calorimeter test, peak heat release rate(HRR) and total heat release(THR), expanded thickness and expansion rate of each composite material of expandable graphite, and fire prone crack and mass loss rate after burning was measured. Thus, the effect of the addition of the expandable graphite and whether is suitable for reference as a fire retardant, was analyzed. Consequently the correlation of THR and fire retardant performance rate was confirmed.

• Korean Journal of Materials Research
• /
• v.19 no.10
• /
• pp.555-561
• /
• 2009

Expanded graphite (EG) is synthesized by chemical intercalation of natural graphite (NG) and rapid expansion at high temperature, with titanium n-butoxide (TNB) used as titanium source by a sol-gel method to prepare EG-TiO$_2$ composite. The performances of the prepared EG-TiO$_2$ composite are characterized by BET surface area measurement, scanning electron microscopy (SEM), X-ray diffraction patterns (XRD) and energy dispersive X-ray analysis (EDX). To compare the photocatalytic activities of the EG-TiO$_2$ composite, three kinds of dye solutions, methylene blue (MB), methylene orange (MO) and rhodamine B (RhB), and two kinds of light source, UV light and visible light (VL), are used. Comparing the results, it can be clearly seen that the degradation of all of the dye solutions under irradiation by UV light is much better than that under irradiation by visible light, and the decomposition of MB solution was better than that of both of MO and RhB solution.

• Journal of the Korea Institute of Building Construction
• /
• v.18 no.6
• /
• pp.559-567
• /
• 2018

In the case of fire, surface treatment agents used in external insulation finishing methods are substances that are vulnerable to fire due to thin finishes and the combustion of polymers. In this study, it was expected that the performance of surface preparation mortars could be improved by using expandable graphite with excellent thermal performance. Experimental results showed that the mechanical properties of surface preparation mortar were improved by using the fly ash and silica fume. Surface treatment materials using expanded graphite have a characteristic of expanding when a fire occurs. It has been shown that heat-swellable surface treatment materials can reduce the penetration of heat sources into the surface of synthetic insulation.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.11a
• /
• pp.103.2-103.2
• /
• 2011

리튬이차전지의 음극물질로서 상용화되고 있는 탄소재료중 흑연은 전기자동차에 적용하기에는 낮은 용량과 나쁜 출력특성을 갖고 있어 지금보다 두배이상의 용량과 출력특성이 좋은 음극소재의 개발이 필요하다. 또 다른 음극물질로 실리콘은 흑연에 비해 월등히 높은 이론용량을 나타내고 있지만 실리콘이 리튬이온과 만나면 부피가 4배이상 팽창하여 사이클이 진행될수록 충방전 용량이 급격히 감소하게 된다. 그래서 본 연구에서는 이 두 음극소재를 상호보완하기 위해 천연흑연을 산처리 과정을 통해 제조된 팽창흑연을 매트릭스로 사용하여 팽창흑연에 실리콘을 충진 시키는 연구를 진행하였다. 팽창흑연에 실리콘을 충진시킴으로써 1C일 때 약 650mAh/g의 용량을 나타내었으며, 50cycle이 진행된 후에도 비교적 안정한 사이클 특성을 나타내었다.

• Applied Chemistry for Engineering
• /
• v.25 no.5
• /
• pp.463-467
• /
• 2014

In this paper, the thermal behaviors of expanded graphite(EG)/erythritol composites with different contents of EG were studied. The surface and structure properties of the composites were determined by using scanning electron microscope (SEM), transmission electron microscope (TEM), and X-ray diffraction (XRD), respectively. The thermal properties were investigated by differential scanning calorimetry (DSC) and thermal conductivity (TC). As experimental results, the thermal conductivity of the composites increased with increasing the EG content. However, the latent heat was somewhat decreased in the presence of EG. We could concluded that EG was highly promising materials for improving the heat transfer enhancement and energy storage capacity of phase change materials (PCMs).

• Applied Chemistry for Engineering
• /
• v.28 no.4
• /
• pp.437-441
• /
• 2017

This study was carried out to investigate the volumetric expansion ratio and hardness of expanded graphite after coating with various resins which were used as an additive of fireproof sealant. The coating thickness of the resin, which represents the coating rate, was dependent of the drying speed of the resin and the viscosity of the resin. Therefore the coating thickness was shown as follows: polyvinyl acetate > acrylic resin > urethane resin > water soluble latex. Furthermore, the volumetric expansion ratio was as follows: urethane resin > water soluble latex > acrylic resin > polyinyl acetate and the hardness was as follows: polyvinyl acetate resin > acrylic resin > water soluble latex > urethane resin. This showed that the volume of expansion was reduced by expansion, which was not covered by coating, but significantly increased by increasing hardness and allowed it to be used as a refractory addition. According to the response surface methodology, the optimized addition amount and stirring speed of acrylic resin were 37.6 wt% and 441.4 rpm, respectively.

• Proceedings of the Korea Society for Energy Engineering kosee Conference
• /
• 1999.05a
• /
• pp.185-191
• /
• 1999

An air-conditioning system based on the chemical heat storage principle was considered. $H_2O$ was chosen as the reaction gas and the working fluid as well. Na$_2$S, CaCl$_2$, MnCl$_2$, BaCl$_2$, MgCl$_2$, Fe$_2$(SO$_4$)$_3$ and MnSO$_4$ were tested as the solid reactants by using Cahn pressure balance. Na$_2$S was superior to other salts in respect of high capability of absorption of water gas, 5 moles of $H_2O$ per unit mole of Na$_2$S, and adequate temperature of adsorption, $65^{\circ}C$ at 7torr, and of desorption, 13$0^{\circ}C$ at 76torr. Clausius-Clapeyron diagram of Na$_2$S was obtained via adsorption experiments at several vapor pressures of water gas. To enhance heat and mass transfer characteristics, usually below 1W/m K, of the reactor bed of general adsorption systems, expanded graphite block was adapted as the support of Na$_2$S salt. Expanded graphite blocks had thermal conductivity values of 20~80W/mK with respect to 100~400kg/㎥ of block bulk density. Permeability values of expanded graphite blocks were 10$^{-13}$ ~ 10$^{-14}$ $m^2$ with respect to 100~300kg/㎥ of block bulk density showing highly decreasing values of permeability, below 10$^{-l4}$$m^2$, in the range of above 150kg/㎥ of block bulk density.y.

• Journal of the Korean GEO-environmental Society
• /
• v.13 no.5
• /
• pp.35-40
• /
• 2012

In this study, adsorption characteristics of expanded graphite (EG) were investigated by a series of batch adsorption tests using p-Xylene as a model volatile organic compounds (VOCs). After acid treatment, graphite were expanded at various temperature from $600^{\circ}C$ to $1000^{\circ}C$ for one minute. The optimal temperature was $800^{\circ}C$, where the expansion ratio reached 195 times of original volume. The BET specific surface area of EG was $92.4m^2/g$, which was only 1/10 of granular activated carbon (GAC), however the adsorption of p-Xylene by EG was almost completed within 5 minutes while that of GAC continued for 7 days because the majority of pores of EG was consisted with meso- and macro-pores. According to the Langmuir isotherm analysis, the maximum specific adsorption of p-Xylene onto EG was 24.0 mg/L with the adsorption constant of 7.94. In conclusion, the adsorption capacity of EG was much less than that of GAC due to the significantly lower specific surface area, but the first order kinetic constant was more than 500 times larger than GAC. Overall, EG might be effective where the fast adsorption is required.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.12 no.4
• /
• pp.1999-2004
• /
• 2011

This research aims to develop polymer composites which can be used for PEMFC bipolar plate by injection molding process. Considering the moldability and stiffness, we used LCP(Liquid crystal polymer) as base resin. In order to improve electrical conductivity and mechanical properties, we chose carbon black, and both synthetic graphite and expanded graphite. The composites with different recipe are prepared for injection molding of PEMFC bipolar plate and CAE(Computer Aided Engineering) analysis was performed to predict melt flow and fiber orientation We did successfully fabricate the ASTM specimens by injection molding, and measure the electrical conductivity of the samples by using four point probe device. We measured mechanical properties such as flexural strength, flexural modulus and Izod impact strength. Conclusively, the electrical conductivity increased with increasing additive concentration, but both flexural strength and Izod impact strength decreased due to the brittle nature of carbon-based additives.

• Carbon letters
• /
• v.27
• /
• pp.117-120
• /
• 2018