• Journal of the Korean Ceramic Society
• /
• v.43 no.3 s.286
• /
• pp.185-192
• /
• 2006

The effects of annealing on structural and electrical properties of ITO/PES (Indium Tin Oxide/Polyethersulfone) films was investigated. Amorphous ITO thin films were grown on plastic substrates, PES using low temperature DC magnetron sputtering. Various post annealing techniques were attempted to research variations of microstructure and electrical properties: i) conventional thermal annealing, ii) excimer laser annealing, iii) UV irradiation. The electrical properties were obtained using Hall effect measurements and DC 4-point resistance measurement. The microstructural features were characterized by FESEM, XRD, Raman spectroscopy in terms of morphology and crystallinity. Optimized UV treatment exhibits the enhanced conductivity and crystallinity, compared to those of conventional thermal annealing.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.356-356
• /
• 2010

In this paper, Poly silicon thin-film transistors (poly-Si TFTs) with employed the SPC (Solid phase crystallization) and ELA (Excimer laser annealing) methods on glass panel substrate are fabricated to investigate the electrical poperies. Poly-Si TFTs have recess-channel structure with formated source/drain regions by LPCVD n+ poly Si in low $650^{\circ}C$ temperature. the ELA-TFT show higher on/off current ratio and subthreshold swing than a-Si and SPC TFT that therefore, these results showed that the ELA-TFT might be beneficial for practical embedded TFT memory device application.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2008.10a
• /
• pp.1261-1262
• /
• 2008

Laser-based crystallization techniques are ideally-suited for forming high-quality crystalline Si films on active-matrix display backplanes, because the highly-localized energy deposition allows for transformation of the as-deposited a-Si without damaging high-temperature-intolerant glass and plastic substrates. However, certain significant and non-trivial attributes must be satisfied for a particular method and implementation to be considered manufacturing-worthy. The crystallization process step must yield a Si microstructure that permits fabrication of thin-film transistors with sufficient uniformity and performance for the intended application and, the realization and implementation of the method must meet specific requirements of viability, robustness and economy in order to be accepted in mass production environments. In recent years, Low Temperature Polycrystalline Silicon (LTPS) has demonstrated its advantages through successful implementation in the application spaces that include highly-integrated active-matrix liquid-crystal displays (AMLCDs), cost competitive AMLCDs, and most recently, active-matrix organic light-emitting diode displays (AMOLEDs). In the mobile display market segment, LTPS continues to gain market share, as consumers demand mobile devices with higher display performance, longer battery life and reduced form factor. LTPS-based mobile displays have clearly demonstrated significant advantages in this regard. While the benefits of LTPS for mobile phones are well recognized, other mobile electronic applications such as portable multimedia players, tablet computers, ultra-mobile personal computers and notebook computers also stand to benefit from the performance and potential cost advantages offered by LTPS. Recently, significant efforts have been made to enable robust and cost-effective LTPS backplane manufacturing for AMOLED displays. The majority of the technical focus has been placed on ensuring the formation of extremely uniform poly-Si films. Although current commercially available AMOLED displays are aimed primarily at mobile applications, it is expected that continued development of the technology will soon lead to larger display sizes. Since LTPS backplanes are essentially required for AMOLED displays, LTPS manufacturing technology must be ready to scale the high degree of uniformity beyond the small and medium displays sizes. It is imperative for the manufacturers of LTPS crystallization equipment to ensure that the widespread adoption of the technology is not hindered by limitations of performance, uniformity or display size. In our presentation, we plan to present the state of the art in light sources and beam delivery systems used in high-volume manufacturing laser crystallization equipment. We will show that excimer-laser-based crystallization technologies are currently meeting the stringent requirements of AMOLED display fabrication, and are well positioned to meet the future demands for manufacturing these displays as well.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.313-313
• /
• 2013

For high-performance TFT (Thin film transistor), poly-crystalline semiconductor thin film with low resistivity and high hall carrier mobility is necessary. But, conventional SPC (Solid phase crystallization) process has disadvantages in fabrication such as long annealing time in high temperature or using very expensive Excimer laser. On the contrary, MIC (Metal-induced crystallization) process enables semiconductor thin film crystallization at lower temperature in short annealing time. But, it has been known that the poly-crystalline semiconductor thin film fabricated by MIC methods, has low hall mobility due to the residual metals after crystallization process. In this study, Ni metal was shallow implanted using PIII&D (Plasma Immersion Ion Implantation & Deposition) technique instead of depositing Ni layer to reduce the Ni contamination after annealing. In addition, the effect of external magnetic field during annealing was studied to enhance the amorphous silicon thin film crystallization process. Various thin film analytical techniques such as XRD (X-Ray Diffraction), Raman spectroscopy, and XPS (X-ray Photoelectron Spectroscopy), Hall mobility measurement system were used to investigate the structure and composition of silicon thin film samples.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.430-430
• /
• 2008

Using multi plasma enhanced chemical vapor deposition system (Multi-PECVD), p-a-Si:H deposition layer as a $p^+$ region which was annealed by laser (Q-switched fiber laser, $\lambda$ = 1064 nm) on an n-type single crystalline Si (100) plane circle wafer was prepared as new doping method for single crystalline interdigitated back contact (IBC) solar cells. As lots of earlier studies implemented, most cases dealt with the excimer (excited dimer) laserannealing or crystallization of boron with the ultraviolet wavelength range and $10^{-9}$ sec pulse duration. In this study, the Q-switched fiber laser which has higher power, longer wavelength of infrared range ($\lambda$ = 1064 nm) and longer pulse duration of $10^{-8}$ sec than excimer laser was introduced for uniformly deposited p-a-Si:H layer to be annealed and to make sheet resistance expectable as an important process for IBC solar cell $p^+$ layer on a polished n-type Si circle wafer. A $525{\mu}m$ thick n-type Si semiconductor circle wafer of (100) plane which was dipped in a buffered hydrofluoric acid solution for 30 seconds was mounted on the Multi-PECVD system for p-a-Si:H deposition layer with the ratio of $SiH_4:H_2:B_2H_6$ = 30:120:30, at $200^{\circ}C$, 50 W power, 0.2 Torr pressure for 20 minutes. 15 mm $\times$ 15 mm size laser cut samples were annealed by fiber laser with different sets of power levels and frequencies. By comparing the results of lifetime measurement and sheet resistance relation, the laser condition set of 50 mm/s of mark speed, 160 kHz of period, 21 % of power level with continuous wave mode of scanner lens showed the features of small difference of lifetime and lowering sheet resistance than before the fiber laser treatment with not much surface damages. Diode level device was made to confirm these experimental results by measuring C-V, I-V characteristics. Uniform and expectable boron doped layer can play an important role to predict the efficiency during the fabricating process of IBC solar cells.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.287.1-287.1
• /
• 2014

본 연구에서는 현재 디스플레이에서 가장 널리 이용되는 저온 polycrystalline silicon (poly-Si)의 결정화 방법에 따른 thin-film transistor (TFT)의 전기적 특성을 분석하였다. 분석에 이용된 결정화 방식은 Excimer Laser Annealing (ELA)와 Metal Induced Crystallization (MIC)이다. ELA와 MIC TFTs의 전기적 특성 측정을 통한 분석결과 ELA와 MIC poly-Si TFTs의 전기적 특성 [field-effect mobility (${\mu}_{FE}$), on/off current ratio ($I_{ON}/I_{OFF}$), sub-threshold swing (SS)]은 큰 차이는 없지만, ELA를 이용한 poly-Si TFT의 전기적 특성이 조금 우수하다. 하지만, MIC poly-Si TFT의 경우 threshold voltage ($V_{TH}$)가 0V에 보다 가까울 뿐만 아니라, 전기적 스트레스를 통한 신뢰성 확인 시 ELA poly-Si TFT보다 조금 더 안정적이다. 이는 ELA의 경우 좁은 면에 선형 레이저 빔으로 조사하면서 생기는 hill-lock의 영향으로 표면이 거칠고 균일하지 못하여 바이어스 인가시 생기는 문제이다. 또한 MIC는 금속 촉매를 이용해 결정립 경계를 확장하고 결정 크기를 키워 대면적화에 유리하다. Thermal Stress에서는 (from 293K to 373K) TFT에 점차 높은 온도를 가하자 MIC poly-Si TFT의 경우 off 상태에서 누설 전류 값이 증가하며 열에 민감한 반응을 보이는 것을 확인하였다.

• Proceedings of the IEEK Conference
• /
• 2001.06b
• /
• pp.225-228
• /
• 2001

We simulated and analyzed the flicker phenomena in the poly-Si TFT-LCD using PSpice for the development of wide-area and high-quality LCD display We define the electric quantity of flicker in the TFT-LCD, which is the ratio of half frame frequency (30Hz) to DC (0 Hz) frequency. We compared two different types of TFTs, excimer laser annealed (ELA) poly-Si TFT and silicide mediated crystallization (SMC) poly-Si TFT, and found that the ELA and SMC TFTs show different flicker characteristics because of their mobility and leakage current. In addition, we showed that the gate voltage should be chosen carefully at the minimum flicker because of the larger leakage current of poly-Si Tn as compared with a-Si TFT

• Proceedings of the KIEE Conference
• /
• 2000.11c
• /
• pp.461-463
• /
• 2000

This paper presents a low temperature excimer-laser-crystallization that produces directionally solidified microstructure in Si thin films. The process involves (1) a complete melting of selected area via irradiation through a patterned mask. and (2) a precisely controlled pulse translation of the sample with respect to the mask over a distance shorter than the superlateral growth(SLG) distance. (3) lateral growth extended over a number of iterative steps. Grains that grow continuously to the vertical direction were demonstrated. We discuss sequential lateral solidification principle, experiment.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.429-429
• /
• 2010

TFT 제조 방법 중 LTPS (Low Temperature Polycrystalline Silicon)는 저온과 저비용 등의 이점으로 인하여 flat panel display 제작에 널리 사용된다. 이동도와 전류 점멸비 등에서 이점을 가지는 ELA(Excimer Laser Annealing)가 널리 사용되고 있지만, 이 방법은 uniformity 등의 문제점을 가지고 있다. 이를 극복하기 위한 방법으로 MICC(Metal Induced Capping Crystallization)이 사용되고 있다. 이 방법은 $SiN_x$, $SiO_2$, SiON등의 capping layer를 diffusion barrier로 위치시키고, Ni 등의 금속을 capping layer에 도핑 한 뒤, 다시 한번 열처리를 통하여 a-Si에 Ni을 확산시키킨다. a-Si 층에 도달한 Ni들이 seed로 작용하여 Grain size가 매우 큰 film을 제작할 수 있다. 채널의 grain size가 클 경우 grain boundary에 의한 캐리어 scattering을 줄일 수 있기 때문에 MIC 방법을 사용하였음에도 ELA에 버금가는 소자의 성능과 안정성을 얻을 수있었다. 본 연구에서는 large grain TFT의 Gate bias stress에 따른 소자의 안정성 측정 및 분석에 목표를 두었다.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2002.08a
• /
• pp.159-162
• /
• 2002

This paper reviews an advanced excimer-laser crystallization technique enabling precise location-control of the individual grains. With the developed ${\mu}$-Czochralski (grain-filter) process, the large grains having a diameter of 6 ${\mu}m$ can be set precisely at predetermined positions. We will also discuss the performance of the single-crystalline Si TFTs that are formed within the location-controlled Si grains. The field-effect mobility for electrons is 430 $cm^2/Vs$ on average, which is well comparable to that of TFTs made with silicon-on-insulator wafers.