• Journal of the Korean Ceramic Society
• /
• v.28 no.12
• /
• pp.981-988
• /
• 1991

Various crystal defects such as voids, inclusions dislocations, stacking faults and precipitates were observed in the Czochralski-grown Bi12GeO20 crystals. Particularly, precipitates were found in the whole crystals. The phase of these precipitates was identified as Bi4Ge3O12 by EPMA and transmission electron microscopy. The precipitates were produced by pulling rapidly from a non-stoichiometric charge. During the pulling of Bi12GeO20 crystals, the melt composition of stoichiometric charge was changed Bi-deficent with gradual volatilization of Bi2O3. Precipition of the second phase may have been affected by an abrube thermal stress. By adding excess Bi2O3 into the stoichiometric batch, the precipitation of Bi4Ge3O12 was suppressed. At a pulling speed of 2 mm/hr, clear and precipitate from crystals of Bi12GeO20 were grown from the melt of the Bi2O3 excess charge.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.15 no.9
• /
• pp.764-769
• /
• 2002

The effect of excess Bi contents on the ferroelectric properties of B $i_{3.25}$ L $a_{0.75}$ $Ti_3$ $O_{12}$ (BLT) thin films has been investigated. Bismuth lanthanum titanate thin films with excess Bi contents were prepared onto Pt/Ti/ $SiO_2$/Si substrate by metalorganic decomposition (MOD) technique. The structure and morphology of the films were analyzed using X-ray diffraction (XRD) and atomic force microscopy (AFM), respectively. From the XRD analysis, BLT thin films show polycrystalline structure and the layered-perovskite phase was obtained over 10% excess of Bi contents. As a result of ferroelectric characteristics related to the Bi content of the BLT thin film, the remanent polarization and dielectric constant decreased with increasing over Bi content of 10% excess. The BLT film with Bi content of 10% excess was measured to have a dielectric constant of 326 and dielectric loss of 0.024. The BLT thin films showed little polarization fatigue test up to 3.5$\times$10$^{9}$ bipolar switching cycling.

• Korean Journal of Materials Research
• /
• v.27 no.3
• /
• pp.144-148
• /
• 2017

The effects of an excess of Bi on the piezoelectric and dielectric properties of $0.60Bi_{1+x}FeO_3-0.40BaTiO_3$ (x = 0, 0.01, 0.03, 0.05, 0.07) were investigated. The ceramics were processed through a conventional solid state reaction method and then quenched after sintering at different temperatures in the range of $980{\sim}1070^{\circ}C$. A single perovskite structure without any secondary phase was confirmed for all compositions and temperatures. It was found that excess Bi reduced the sintering temperatures, acted as a sintering aid and enhanced the properties in combination with quenching. Curie temperature ($T_C$) was found to slightly increase due to the presence of excess Bi; electrical properties were also improved by quenching. At x = 0.03 and $1030^{\circ}C$, remnant polarization ($2P_r$) was as high as $45.4{\mu}C/cm^2$ and strain at 40 kV/cm was up to 0.176 %.

• Applied Chemistry for Engineering
• /
• v.3 no.1
• /
• pp.53-63
• /
• 1992

M/BM -series catalysts, $MoO_3$ supported on ${\alpha}-Bi_2Mo_3O_{12}$ were also prepared by impregnation method. BM/M-series catalysts, ${\alpha}-Bi_2Mo_3O_{12}$ supported on $MoO_3$ were also prepared by coprecipitation. Structure and catalytic properties of the two phase catalysts were studied by means of using nitrogen adsorption, X-ray diffraction, and scanning electron microscopy. The reaction test for the selective oxidation of propylene to acrolein over Bi-molybdate catalysts was studied using a fixed-bed reactor system. In M/BM-series catalysts, $MoO_3$ was dispersed on ${\alpha}-Bi_2Mo_3O_{12}$, and the crystal structure of ${\alpha}-Bi_2Mo_3O_{12}$ remains unchanged by the presence of excess $MoO_3$. However the surface morphology and bulk structure of BM/M-series catalysts were altered probably because the precipitated $Bi(OH)_3$ reacted with $MoO_3$ during the calcination to form ${\alpha}-Bi_2Mo_3O_{12}$ phase. The results of propylene oxidation on both series catalysts showed that the reaction took place over the surface of ${\alpha}-Bi_2Mo_3O_{12}$ particle and the role of excess $MoO_3$ was to supply oxygen to ${\alpha}-Bi_2Mo_3O_{12}$. These increasing effects on activity were also observed in the mechanical mixtures of ${\alpha}-Bi_2Mo_3O_{12}$ and $MoO_3$.

• Journal of the Korean Ceramic Society
• /
• v.53 no.2
• /
• pp.162-166
• /
• 2016

0.75BF-0.25BT ceramics were prepared by sintering at $980-1040^{\circ}C$ in air or under atmosphere powder. A sample with 1 mole %-excess $Bi_2O_3$ was also prepared to compensate for $Bi_2O_3$-evaporation. Physical and piezoelectric properties of these three samples were compared. When the sintering temperature increased from $980^{\circ}C$ to $1040^{\circ}C$, the density of the sample sintered in air decreased continuously due to Bi-evaporation. Due to the suppression of Bi-evaporation, the sample sintered under atmosphere powder had a higher density at sintering temperatures above $1000^{\circ}C$ than did the sample sintered in air. The addition of 1 mole %-excess $Bi_2O_3$ successfully compensated for Bi-evaporation and kept the density at the higher value until $1020^{\circ}C$. Grain size increased continuously when the sintering temperature increased from 980 to $1040^{\circ}C$, irrespective of the sintering atmosphere. When the sintering temperature increased, the piezoelectric constant ($d_{33}$) and the electromechanical coupling factor ($k_p$) increased for all samples. The sample with 1 mole % excess-$Bi_2O_3$ showed the highest density and the best piezoelectric properties at sintering temperature of $1020^{\circ}C$.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07a
• /
• pp.371-374
• /
• 2002

Bismuth lanthanum titanate thin films with excess Bi contents were prepared onto Pt/Ti/$SiO_2$/Si substrate by metalorganic decomposition (MOD) technique. The structure and morphology of the films were analyzed using X-ray diffraction (XRD) and atomic force microscopy (AFM), respectively. From the XRD analysis, BLT thin films show polycrystalline structure and the layered-perovskite phase was obtained over 10% excess of Bi contents. As a result of ferroelectric characteristics related to the Bi content of the BLT thin film, the remanent polarization and dielectric constant decreased with increasing over Bi content of 10 % excess. The BLT film with Bi content of 10% excess was measured to have a dielectric constant of n9 and dielectric loss of 1.85[%]. The BLT thin films showed little polarization fatigue test up to 3.5 x $10^{9}$ bipolar switching cycling.

• Journal of the Korean Ceramic Society
• /
• v.37 no.2
• /
• pp.186-193
• /
• 2000

Effects of 1.0 mol% CoO addition on sintering and the electrical properties of ZnO-Bi2O3-Sb2O3(ZBS) varistor system with 3.0 mol% co-addition of Sb2O3 and Bi2O3 at various Sb/Bi ratio (0.5, 1.0, and 2.0) were investigated. Cobalt had little influence on the liquid-phase formation and the pyrochlore decomposition temepratures of ZBS, while densification was mainly dependent on Sb/Bi ratio: when Sb/Bi=0.5, excess Bi2O3 irrelevant to the formation of pyrochore(Zn2Sb3Bi3O14) forms eutectic liquid at ~75$0^{\circ}C$ which promotes densification and grain growth; with Sb/Bi=2.0, the second phase Zn7Sb2O12 formed by excess Sb2O3 irrelevant to the formation of the pyrochlore retards densification up to ~100$0^{\circ}C$. These phases caused the coarsening and uneven distribution of the second phase particles on the grain boundaries of ZnO above the pyrochlore decomposition temperature(~105$0^{\circ}C$), which led to broad size dist-ribution of ZnO; the specimen with Sb/Bi=1.0 showed homogeneous microstructure compared with the others, which enabled improved varistor characteristics. Doping of Co increased the nonlinearity and the potential barrier height of ZBS, which is thought to stem from improved sintering behavior such as homogenized microstructure due to size reduction and even distribution of the second phase and suppressed volatility of Bi2O3, as well as the improvement in the potential barrier structure via increased donor and interface electron trap densities.

• The Korean Journal of Ceramics
• /
• v.6 no.3
• /
• pp.276-279
• /
• 2000

Ferroelectric properties of $SrBi_2TaNbO_9$ (SBTN) thin films were changed by the amount of Bi content in SBTN. We suggested that the addition of excess Bi into the films could be accomplished by heat-treating $SBTN/Bi_2O_3/SBTN$ heterostructure fabricated by r.f. magnetron sputtering method. Excess Bi composition was controlled by the thickness of the sandwiched $Bi_2O_3$ from 0 to $400\;\AA$. When the SBTN thin films were inserted by $400\;{\AA}\;Bi_2O_3$ layer, $Bi_2Pt$ phase was formed as a second phase in SBTN films, resulting in poor ferroelectric properties. The onset temperature for hysteresis loop can be reduced by heat treating $SBTN/Bi_2O_3/SBTN$ heterostructure. The films with $SBTN/Bi_2O_3(100\;{\AA})/SBTN$ hetero-structure followed by annealing at $650^{\circ}C$ for 30 min show 2Pr and Ec of $5.66\;{\mu}C/\textrm{cm}^2$ and 54 kV/cm, respectively.

• Journal of the Microelectronics and Packaging Society
• /
• v.20 no.4
• /
• pp.25-30
• /
• 2013

Pb-free ferroelectric $(Na_{0.5}Bi_{0.5})TiO_3$ (NBT) thin films were prepared by a modified sol-gel process. Their structural, dielectric and pyroelectric properties were investigated as a function of the excess Na/Bi ratio and the annealing temperature. In the case of thin films containing no excess Na and Bi, only partial amounts of the perovskite NBT were crystallized, where the films consisted mainly of the pyrochlore phase of $Bi_2Ti_2O_7$ for annealing conditions of $600{\sim}800^{\circ}C$. With increasing excess Na/Bi ratio, the proportion of the perovskite phase effectively increased due to the compensation of the volatile Na and Bi components. For a Na/Bi ratio of 2.0, the thin film with single NBT perovskite phase was obtained within XRD detection limit after annealing at $700^{\circ}C$ for 10 min and it showed the excellent dielectric properties, ${\varepsilon}r$ of ~550 and tan ${\delta}$ of 0.03. While these properties were degraded for Na/Bi ratio of 2.5 despite the existence of pure perovskite phase. The NBT thin film with Na/Bi ratio of 2.0 are also promising candidates for applications requiring pyroelectric devices because it was found to have pyroelectric coefficients of $1.3{\sim}7nC/cm^2K$ in the temperature range of $30{\sim}100^{\circ}C$.

• Korean Journal of Materials Research
• /
• v.30 no.2
• /
• pp.61-67
• /
• 2020

BiFeO₃ with perovskite structure is a well-known material that has both ferroelectric and antiferromagnetic properties called multiferroics. However, leaky electrical properties and difficulty of controlling stoichiometry due to Bi volatility and difficulty of obtaining high relative density due to high dependency on the ceramic process are issues for BiFeO₃ applications. In this work we investigated the sintering behavior of samples with different stoichiometries and sintering conditions. To understand the optimum sintering conditions, nonstoichiometric Bi_1±xFeO_3±δ ceramics and Ti-doped Bi_1.03Fe_1-4x/3Ti_xO₃ ceramics were synthesized by a conventional solid-state route. Dense single phase BiFeO₃ ceramics were successfully fabricated using a two-step sintering and quenching process. The effects of Bi volatility on microstructure were determined by Bi-excess and Ti doping. Bi-excess increased grain size, and Ti doping increased sintering temperature and decreased grain size. It should be noted that Ti-doping suppressed Bi volatility and stabilized the BiFeO₃ phase.