• 한국세라믹학회지
• /
• 제28권12호
• /
• pp.981-988
• /
• 1991

Various crystal defects such as voids, inclusions dislocations, stacking faults and precipitates were observed in the Czochralski-grown Bi12GeO20 crystals. Particularly, precipitates were found in the whole crystals. The phase of these precipitates was identified as Bi4Ge3O12 by EPMA and transmission electron microscopy. The precipitates were produced by pulling rapidly from a non-stoichiometric charge. During the pulling of Bi12GeO20 crystals, the melt composition of stoichiometric charge was changed Bi-deficent with gradual volatilization of Bi2O3. Precipition of the second phase may have been affected by an abrube thermal stress. By adding excess Bi2O3 into the stoichiometric batch, the precipitation of Bi4Ge3O12 was suppressed. At a pulling speed of 2 mm/hr, clear and precipitate from crystals of Bi12GeO20 were grown from the melt of the Bi2O3 excess charge.

• 한국전기전자재료학회논문지
• /
• 제15권9호
• /
• pp.764-769
• /
• 2002

The effect of excess Bi contents on the ferroelectric properties of B $i_{3.25}$ L $a_{0.75}$ $Ti_3$ $O_{12}$ (BLT) thin films has been investigated. Bismuth lanthanum titanate thin films with excess Bi contents were prepared onto Pt/Ti/ $SiO_2$/Si substrate by metalorganic decomposition (MOD) technique. The structure and morphology of the films were analyzed using X-ray diffraction (XRD) and atomic force microscopy (AFM), respectively. From the XRD analysis, BLT thin films show polycrystalline structure and the layered-perovskite phase was obtained over 10% excess of Bi contents. As a result of ferroelectric characteristics related to the Bi content of the BLT thin film, the remanent polarization and dielectric constant decreased with increasing over Bi content of 10% excess. The BLT film with Bi content of 10% excess was measured to have a dielectric constant of 326 and dielectric loss of 0.024. The BLT thin films showed little polarization fatigue test up to 3.5$\times$10$^{9}$ bipolar switching cycling.

• 한국재료학회지
• /
• 제27권3호
• /
• pp.144-148
• /
• 2017

The effects of an excess of Bi on the piezoelectric and dielectric properties of $0.60Bi_{1+x}FeO_3-0.40BaTiO_3$ (x = 0, 0.01, 0.03, 0.05, 0.07) were investigated. The ceramics were processed through a conventional solid state reaction method and then quenched after sintering at different temperatures in the range of $980{\sim}1070^{\circ}C$. A single perovskite structure without any secondary phase was confirmed for all compositions and temperatures. It was found that excess Bi reduced the sintering temperatures, acted as a sintering aid and enhanced the properties in combination with quenching. Curie temperature ($T_C$) was found to slightly increase due to the presence of excess Bi; electrical properties were also improved by quenching. At x = 0.03 and $1030^{\circ}C$, remnant polarization ($2P_r$) was as high as $45.4{\mu}C/cm^2$ and strain at 40 kV/cm was up to 0.176 %.

• 공업화학
• /
• 제3권1호
• /
• pp.53-63
• /
• 1992

프로필렌을 선택산화시켜 아크로레인을 제조하는 반응을 Bi-molybdate 촉매상에서 고정층 반응기를 사용하여 연구하였다. ${\alpha}-Bi_2Mo_3O_{12}$위에 $MoO_3$를 담지시킨 M/BM-series 촉매는 함침법으로 제조되었고, 역으로 BM/M-series 촉매는 $MoO_3$위에 ${\alpha}-Bi_2Mo_3O_{12}$을 침전시켜 제조하였다. 또한 촉매의 특성분석을 위하여 질소흡착과 XRD, SEM을 이용하였다. M/BM-series 촉매에서는 $MoO_3$가 작은 입자로 분산되고 ${\alpha}-Bi_2Mo_3O_{12}$의 결정구조는 $MoO_3$상이 추가되어도 그 형상이 변하지 않는 채로 유지되었으나, BM/M-series 촉매의 표면형상 및 전체 구조는 촉매제조 중에 생기는 침전물인 $Bi(OH)_3$가 소성 도중 $MoO_3$와 반응하여 ${\alpha}-Bi_2Mo_3O_{12}$을 형성하는 관계로 그 조성에 따라 매우 불규칙적으로 변화하였다. 반응실험 결과, 두 종류의 촉매 모두에서 excess $MoO_3$가 포함되었을 때 활성이 크게 증가하였는데, 이는 선별산화반응이 주로 ${\alpha}-Bi_2Mo_3O_{12}$에서 일어나고 $MoO_3$는 ${\alpha}-Bi_2Mo_3O_{12}$에 산소 공급을 원활히 하여 활성을 증가시키기 때문으로 판명되었다. 또한 이러한 활성 증가는 ${\alpha}-Bi_2Mo_3O_{12}$와 기계적 혼합물 (mechanical mixture)에서도 관찰되었다.

• 한국세라믹학회지
• /
• 제53권2호
• /
• pp.162-166
• /
• 2016

0.75BF-0.25BT ceramics were prepared by sintering at $980-1040^{\circ}C$ in air or under atmosphere powder. A sample with 1 mole %-excess $Bi_2O_3$ was also prepared to compensate for $Bi_2O_3$-evaporation. Physical and piezoelectric properties of these three samples were compared. When the sintering temperature increased from $980^{\circ}C$ to $1040^{\circ}C$, the density of the sample sintered in air decreased continuously due to Bi-evaporation. Due to the suppression of Bi-evaporation, the sample sintered under atmosphere powder had a higher density at sintering temperatures above $1000^{\circ}C$ than did the sample sintered in air. The addition of 1 mole %-excess $Bi_2O_3$ successfully compensated for Bi-evaporation and kept the density at the higher value until $1020^{\circ}C$. Grain size increased continuously when the sintering temperature increased from 980 to $1040^{\circ}C$, irrespective of the sintering atmosphere. When the sintering temperature increased, the piezoelectric constant ($d_{33}$) and the electromechanical coupling factor ($k_p$) increased for all samples. The sample with 1 mole % excess-$Bi_2O_3$ showed the highest density and the best piezoelectric properties at sintering temperature of $1020^{\circ}C$.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 하계학술대회 논문집
• /
• pp.371-374
• /
• 2002

Bismuth lanthanum titanate thin films with excess Bi contents were prepared onto Pt/Ti/$SiO_2$/Si substrate by metalorganic decomposition (MOD) technique. The structure and morphology of the films were analyzed using X-ray diffraction (XRD) and atomic force microscopy (AFM), respectively. From the XRD analysis, BLT thin films show polycrystalline structure and the layered-perovskite phase was obtained over 10% excess of Bi contents. As a result of ferroelectric characteristics related to the Bi content of the BLT thin film, the remanent polarization and dielectric constant decreased with increasing over Bi content of 10 % excess. The BLT film with Bi content of 10% excess was measured to have a dielectric constant of n9 and dielectric loss of 1.85[%]. The BLT thin films showed little polarization fatigue test up to 3.5 x $10^{9}$ bipolar switching cycling.

• 한국세라믹학회지
• /
• 제37권2호
• /
• pp.186-193
• /
• 2000

Effects of 1.0 mol% CoO addition on sintering and the electrical properties of ZnO-Bi2O3-Sb2O3(ZBS) varistor system with 3.0 mol% co-addition of Sb2O3 and Bi2O3 at various Sb/Bi ratio (0.5, 1.0, and 2.0) were investigated. Cobalt had little influence on the liquid-phase formation and the pyrochlore decomposition temepratures of ZBS, while densification was mainly dependent on Sb/Bi ratio: when Sb/Bi=0.5, excess Bi2O3 irrelevant to the formation of pyrochore(Zn2Sb3Bi3O14) forms eutectic liquid at ~75$0^{\circ}C$ which promotes densification and grain growth; with Sb/Bi=2.0, the second phase Zn7Sb2O12 formed by excess Sb2O3 irrelevant to the formation of the pyrochlore retards densification up to ~100$0^{\circ}C$. These phases caused the coarsening and uneven distribution of the second phase particles on the grain boundaries of ZnO above the pyrochlore decomposition temperature(~105$0^{\circ}C$), which led to broad size dist-ribution of ZnO; the specimen with Sb/Bi=1.0 showed homogeneous microstructure compared with the others, which enabled improved varistor characteristics. Doping of Co increased the nonlinearity and the potential barrier height of ZBS, which is thought to stem from improved sintering behavior such as homogenized microstructure due to size reduction and even distribution of the second phase and suppressed volatility of Bi2O3, as well as the improvement in the potential barrier structure via increased donor and interface electron trap densities.

• The Korean Journal of Ceramics
• /
• 제6권3호
• /
• pp.276-279
• /
• 2000

Ferroelectric properties of $SrBi_2TaNbO_9$ (SBTN) thin films were changed by the amount of Bi content in SBTN. We suggested that the addition of excess Bi into the films could be accomplished by heat-treating $SBTN/Bi_2O_3/SBTN$ heterostructure fabricated by r.f. magnetron sputtering method. Excess Bi composition was controlled by the thickness of the sandwiched $Bi_2O_3$ from 0 to $400\;\AA$. When the SBTN thin films were inserted by $400\;{\AA}\;Bi_2O_3$ layer, $Bi_2Pt$ phase was formed as a second phase in SBTN films, resulting in poor ferroelectric properties. The onset temperature for hysteresis loop can be reduced by heat treating $SBTN/Bi_2O_3/SBTN$ heterostructure. The films with $SBTN/Bi_2O_3(100\;{\AA})/SBTN$ hetero-structure followed by annealing at $650^{\circ}C$ for 30 min show 2Pr and Ec of $5.66\;{\mu}C/\textrm{cm}^2$ and 54 kV/cm, respectively.

• 마이크로전자및패키징학회지
• /
• 제20권4호
• /
• pp.25-30
• /
• 2013

Pb-free ferroelectric $(Na_{0.5}Bi_{0.5})TiO_3$ (NBT) thin films were prepared by a modified sol-gel process. Their structural, dielectric and pyroelectric properties were investigated as a function of the excess Na/Bi ratio and the annealing temperature. In the case of thin films containing no excess Na and Bi, only partial amounts of the perovskite NBT were crystallized, where the films consisted mainly of the pyrochlore phase of $Bi_2Ti_2O_7$ for annealing conditions of $600{\sim}800^{\circ}C$. With increasing excess Na/Bi ratio, the proportion of the perovskite phase effectively increased due to the compensation of the volatile Na and Bi components. For a Na/Bi ratio of 2.0, the thin film with single NBT perovskite phase was obtained within XRD detection limit after annealing at $700^{\circ}C$ for 10 min and it showed the excellent dielectric properties, ${\varepsilon}r$ of ~550 and tan ${\delta}$ of 0.03. While these properties were degraded for Na/Bi ratio of 2.5 despite the existence of pure perovskite phase. The NBT thin film with Na/Bi ratio of 2.0 are also promising candidates for applications requiring pyroelectric devices because it was found to have pyroelectric coefficients of $1.3{\sim}7nC/cm^2K$ in the temperature range of $30{\sim}100^{\circ}C$.

• 한국재료학회지
• /
• 제30권2호
• /
• pp.61-67
• /
• 2020

BiFeO₃ with perovskite structure is a well-known material that has both ferroelectric and antiferromagnetic properties called multiferroics. However, leaky electrical properties and difficulty of controlling stoichiometry due to Bi volatility and difficulty of obtaining high relative density due to high dependency on the ceramic process are issues for BiFeO₃ applications. In this work we investigated the sintering behavior of samples with different stoichiometries and sintering conditions. To understand the optimum sintering conditions, nonstoichiometric Bi_1±xFeO_3±δ ceramics and Ti-doped Bi_1.03Fe_1-4x/3Ti_xO₃ ceramics were synthesized by a conventional solid-state route. Dense single phase BiFeO₃ ceramics were successfully fabricated using a two-step sintering and quenching process. The effects of Bi volatility on microstructure were determined by Bi-excess and Ti doping. Bi-excess increased grain size, and Ti doping increased sintering temperature and decreased grain size. It should be noted that Ti-doping suppressed Bi volatility and stabilized the BiFeO₃ phase.