• Journal of the Korea Institute of Military Science and Technology
• /
• v.13 no.4
• /
• pp.520-527
• /
• 2010

The kill probability of a missile depends on guidance error, warhead performance, and etc. In this paper, we analyzed the kill probability of anti-tank missile in a new approach. Under the condition that the missile hit the target, we studied the effect of angle of attack and impact angle. High impact angle increase the probability that the missile hits the upper armour which is relatively weaker, while high angle of attack at the impact instant decreases the effectiveness of the jet induced by the warhead. We proposed a way to increase the capability of penetration by analyzing the interrelation between impact angle and angle of attack.

• Journal of Navigation and Port Research
• /
• v.37 no.5
• /
• pp.463-469
• /
• 2013

This paper focuses on GPS positioning accuracy variations according to locations of obstacles which surround GPS station. We derived precise coordinates of a GPS station which has a good visibility. Its observation data was rewritten by assuming signal blocking due to obstacle in the elevation angle of $10^{\circ}$ to $70^{\circ}$. We processed daily and hourly data for 10 days. In the results using daily data, RMSE was at 10mm level. And RMSE increased to 100mm levels in case of hourly data. As the elevation angle of obstacle increased, the horizontal and vertical RMSE increased, while the height estimates decreased. These results showed the higher the elevation angle of the obstacle increased the loss of large amounts of data by blocking satellite signals direction. In terms of the direction, when the blocking thing was located in the east or west, the coordinate has larger error in the east-west direction. And if signal was blocked at the south direction, the difference between the east-west error and the south-north position error was reduced.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.35 no.11A
• /
• pp.1078-1084
• /
• 2010

The tracking performance of a big parabola tracking antenna system for tracking and receiving of the signal from the vehicle is impacted by many factors of the internal and the external of the system. In this paper, we analyze the tracking error due to the radio refraction in the application of the tracking and positioning of the vehicle by using radio frequency. The real measurement data are used for the analysis which had been acquired by using GPS and the tracking systems of C- and S-band frequencies in NARO Space centre. To verify the correlation between the tracking errors measured and the radio refraction, we review the error factors and the accuracies of the tracking systems, and the characteristics of the refractivity. The analysis shows that there are angular errors which are due to the radio refraction and not to be neglected, compared to the accuracies of the tracking systems, in case of low elevation angle less than 10 degrees. Also, the tracking errors depend on the target altitude as well as the elevation angle for the case of the target in the troposphere. It is recommended to correct the tracking angle considering the target altitude and elevation angle for the precise target positioning.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.23 no.1
• /
• pp.156-161
• /
• 2009

This paper proposes a new method about performance improvement of soccer robots system by the revision of lens distortion most commonly occurred in camera and the revision of position and angle error in robot patch for the realization of robot position. Among the lens distortions, we revise geometrical distortion and apply it to soccer robots system for realtime environment. Patch used in the recognition and the distinction for coordination and direction of robot occurs a position and angle error according to the figure of it. In this paper, we suggest the method of reduction for position and angle error of robot by improved patch and verify its propriety through the experiment.

• Journal of the Institute of Electronics Engineers of Korea SP
• /
• v.46 no.2
• /
• pp.24-29
• /
• 2009

Sound source localization system is used in a robot, a video conference and CCTV(Closed-circuit television) systems. In this Sound source localization systems are applied to human and they can receive a number of sound data frames during speaking. In this paper, we propose methods which is reducing angle estimation error by selecting sound data frame which can more precisely compute the angles from inputted sound data frame. After selected data converted to angle, the error of sound source localization recognition system can be reduced by applying to medium filter. By the experiment using proposed system it is shown that the average error of angle estimation in sound source recognition system can be reduced up to 31 %.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.66 no.2
• /
• pp.339-346
• /
• 2017

This paper proposes a sensorless control method to improve the performance of an internal permanent magnet synchronous motor (IPMSM) control by using a full-order flux observer in a wide speed range. The conventional sensorless control method uses a constant gain for high performance at low-speed region. However, this method has drawbacks such as an increased angle error and current ripple in the high-speed region due to the fixed gain value. In order to overcome this problem, the gain of the full-order flux observer is changed by considering the angle error in the whole speed range. The proposed method minimizes the angle error for each region of the speed range by applying a relevant gain value, which improves the current ripple reduction and motor noise cancellation. The validity of proposed sensorless control method is verified by a simulation and an experiment.

• ETRI Journal
• /
• v.27 no.3
• /
• pp.280-288
• /
• 2005

This paper presents an efficient algorithm for using the two-axis magnetic compass in portable devices. The general magnetic compass module consists of a three-axis magnetic compass and a two-axis inclinometer to calculate tilt-compensated azimuth information. In this paper, the tilt error is compensated using just a two-axis magnetic compass and two-axis accelerometer. The third-axis data of the magnetic compass is estimated using coordinate information that includes the extended dip angle and tilt information. The extended dip angle is estimated during the normalization process. This algorithm can be used to provide the tilt-compensated heading information to small portable devices such as navigation systems, PDAs, cell phones, and so on.

• Journal of the Korean Institute of Navigation
• /
• v.13 no.1
• /
• pp.1-10
• /
• 1989

Nowadays Hyperbolic Navigation System-LORAN, DECCA, OMEGA, OMEGA-is available on the ocean, and Spherical Navigation System, GPS (Global Positioning System) is operated partially. Hyperbolic Navigation System has the blind area near the base line extention because divergence rate of hyperbola is infinite theoretically. The Position Accuracy is differ from the cross angle of LOP although each LOP has the same error of quantity. GDOP(Geometric Dilution of Precisoin) is used to estimate the position accuracy according to the cross angle of LOP and LOP error. Hyperbola and ellipse are crossed at right angle everywhere. Hyperbola and ellipse are used to LOP in Rectangular Navigation System. The equation calculating the GDOP of rectangular Navigation System is induced and GDOP diagram is completed in this paper. A scheme that can improve the position accuracy in the blind area of Hyperboic Navigation System using the Rectangular Navigation System is proposed through the computer simulation.

• Journal of Institute of Control, Robotics and Systems
• /
• v.7 no.1
• /
• pp.1205-1210
• /
• 2001

This paper describes a methodology using neural network to compensate the nonlinear error of deriving speed for electric differential system included in electric vehicle. An electric differential system which drives each of the left and right wheels of the electric vehicle independently. The electric vehicle driven by induction motor has the nonlinear speed error which depends on a steering angle and speed command. When a vehicle drives along a curved road lane, the speed unblance of inner and outer wheels makes vehicles vibration and speed reduction. To compensate for the speed error, we collected the speed data of the inner wheel and outer wheel in various speed and the steering angle data by using an manufactured electric vehicle and the real system. According to the analysis of the acquisited data, we designed the differential speed control system based on a speed error compensator using neural network.

• Journal of the Korean Society for Precision Engineering
• /
• v.20 no.7
• /
• pp.70-77
• /
• 2003

The centerless through-feed grinding is performed by passing the workpiece between the grinding wheel and the regulating wheel. So, the amount of removed material around the leading end, of the workpiece is always more than that around the trailing end until the leading end leaves the grinding wheel. Because of this, there are differences in diameters along the workpiece axis during grinding, and workpiece axis is not parallel to the grinding wheel axis and the contact lines between the workpiece and wheels. Thus the ground workpiece shows tapering error inherently. To eliminate this error, the workpiece axis must be kept to be parallel to the grinding wheel axis. And, the direction of the workpiece axis can be controlled by the work-rest blade. Therefore, the effects of work-rest blade inclination angle on the through-feed centerless ground part are investigated in this study. As a result, it is found that there is a positive inclination angle of the work-rest blade for minimizing the tapering error of a ground workpiece.