• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.9 no.1
• /
• pp.296-308
• /
• 2015

Advanced Encryption Standard (AES) is widely used for protecting wireless sensor network (WSN). At the Workshop on Cryptographic Hardware and Embedded Systems (CHES) 2012, G$\acute{e}$rard et al. proposed an optimized collision attack and break a practical implementation of AES. However, the attack needs at least 256 averaged power traces and has a high computational complexity because of its byte wise operation. In this paper, we propose a novel double sieve collision attack based on bitwise collision detection, and an improved version with an error-tolerant mechanism. Practical attacks are successfully conducted on a software implementation of AES in a low-power chip which can be used in wireless sensor node. Simulation results show that our attack needs 90% less time than the work published by G$\acute{e}$rard et al. to reach a success rate of 0.9.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.27 no.9
• /
• pp.1351-1363
• /
• 1990

In this paper, a reliable control system structured with dual CPU modules and dual I/O modules is implemented as a means of achieving a highly reliable fault tolerant control system. For this, faults in the system modules are first examined, and a fault detection technique consisting of self diagnostic, comparison process, and exception processing is applied. Self diagnostic is used to locate which components in the modules have been failed, while comparison process is to cmpare control outputs computed by both CPU modules and protect the plant from malfunction by blocking failed control outputsin advance. Finally exception processing is used to determine the faults that are not detected immediately by the self diagnostic and comparison process, e.g. bus error processing when acknowledge signal for data transfer is not activeted in the I/O modules. Also reliability analysis is conducted for the discrete time Markov model with dual structure. It is shown quantitatively that the reliability is improved in the control system with dual structure in comparison with a system with single module structure.

• Proceedings of the KSR Conference
• /
• 2006.11b
• /
• pp.742-747
• /
• 2006

This paper describes online stator-resistance estimation of a linear induction motor(LIM) with cage-type secondary using direct thrust control(DTC), where the resistance value is derived from stator-winding temperature estimation using thermocouple. In this paper, corrected stator resistance has an error in actuality measurement resistance. So compensation coefficient $\kappa$ which is decided through comparison and verifying several times relation of calculated resistance and measured motor line-line resistance. The stator-winding temperature information can also be used for monitoring, protection, and fault-tolerant control of the machine. Also, this paper reports the LIM's responses of the flux measured by the proposed stator resistance compensation algorithm.

• Proceedings of the Korea Information Processing Society Conference
• /
• 2013.11a
• /
• pp.1182-1185
• /
• 2013

도로명주소가 법적 주소체계로 지정되고 2014년도부터 전면 시행을 앞두고 있는 상황에서 기존의 지번주소를 도로명주소로 변경하려는 수요가 늘고 있으며 그에 따라 주소 전환 서비스를 제공하는 솔루션들이 증가하고 있다. 행정구역 체계에 따라 단계별로 입력된 지번주소의 도로명주소로의 변환은 크게 어렵지 않고 변환 성공율도 상당히 높지만 자유롭게 입력하여 정제되지 않은 형태의 주소는 전환에 실패하는 경우가 많다. 본 논문에서는 전산입력된 지번주소를 도로명주소로 변환시 주소형태가 정제되지 않은 상황에서도 변환 성공률을 높이기 위해 행정구역 줄임, 일부 주소정보 누락, 오타 등 여러 가지 변형 케이스에 대해서도 유연하게 변환을 수행하는 방안을 연구하였다. 이를 통해 기존 지번 주소의 표준 형태로의 정제는 최대 두 배까지 변환효율을 높일 수 있었다. 그러나 변환시 사용하는 도로명주소 매칭 테이블에 자료의 누락, 건물명의 불일치, 지번과 건물의 1:1 매칭이 되지 않는 경우가 존재하여 원활한 주소 전환을 위해서는 데이터의 정비가 필요하다.

• Journal of Advanced Navigation Technology
• /
• v.14 no.2
• /
• pp.233-238
• /
• 2010

In this paper, we applied the forward and backward error recovery techniques to a reduced instruction set computer (risc) processor to develop two fault-tolerant processors, namely, fetch redundant risc (FRR) processor and a redundancy execute risc (RER) processor. To evaluate the fault-tolerance capability of three target processors, we developed the base risc processor, FRR processor, and RER processor in SystemC hardware description language. We performed fault injection experiment using the three SystemC processor models and the SystemC-based simulation fault injection technique. From the experiments, for the 1-bit transient fault, the failure rate of the FRR, RER, and base risc processor were 1%, 2.8%, and 8.9%, respectively. For the 1-bit permanent fault, the failure rate of the FRR, RER, and base risc processor were 4.3%, 6.5%, and 41%, respectively. As a result, for 1-bit fault, we found that the FRR processor is more reliable among three processors.

• Journal of Internet Computing and Services
• /
• v.22 no.1
• /
• pp.23-30
• /
• 2021

This paper proposes a noise-tolerant image classification system using multiple autoencoders. The development of deep learning technology has dramatically improved the performance of image classifiers. However, if the images are contaminated by noise, the performance degrades rapidly. Noise added to the image is inevitably generated in the process of obtaining and transmitting the image. Therefore, in order to use the classifier in a real environment, we have to deal with the noise. On the other hand, the autoencoder is an artificial neural network model that is trained to have similar input and output values. If the input data is similar to the training data, the error between the input data and output data of the autoencoder will be small. However, if the input data is not similar to the training data, the error will be large. The proposed system uses the relationship between the input data and the output data of the autoencoder, and it has two phases to classify the images. In the first phase, the classes with the highest likelihood of classification are selected and subject to the procedure again in the second phase. For the performance analysis of the proposed system, classification accuracy was tested on a Gaussian noise-contaminated MNIST dataset. As a result of the experiment, it was confirmed that the proposed system in the noisy environment has higher accuracy than the CNN-based classification technique.

• Journal of Advanced Navigation Technology
• /
• v.20 no.4
• /
• pp.321-328
• /
• 2016

Typical MLC NAND flash devices are considered less reliable than SLC NAND flash devices. Although raw bit error rate (RBER) of MLC flash had been considered approximately 1000times or more higher than that of SLC flash, recent research conducted on Google's data center shows that it is much lower than such expectation. Based on the research, we devised In Drive Data Duplication (IDDD) scheme that efficiently exploit MLC flash's sufficient capacity to improve its data reliability without structural complexity increment using SSD intrinsic firmware layer, and showed the data reliability expectation of MLC flash could be significantly higher than that of SLC flash from measured and calculated error rates. Even though RBER of SLC flash was lower than that of MLC flash in 44 out of 48 cases we studied, applying IDDD scheme, RBER of MLC flash was became lower than that of SLC in all 48 cases and uncorrectable bit error rate (UBER) of MLC flash was became lower than that of SLC flash in 45 out of 48 cases.

• Korean Journal of Organic Agriculture
• /
• v.5 no.1
• /
• pp.67-77
• /
• 1996

The Organic agricultural techinques were investigated through the observations made for 3 years of the actual conditions of a farmer who has been practicing organic agriculture over 21 years. The farmer was a member of the Ichijima-cho Organic Agriculture Association. The Farmer had not performed much of the organic agricultural techinques at the beginning of his farming history. However, he has gradually developed techniques upon the experiences with trial and error. The notable characteristic of his basic organic agriculture was the utilization of a suitable organic fertilizer to make the soil fertile. Crop damages by diseases and insect pests were prevented through a fertile soil, raising of good seedlings, adoption of tolerant varieties and planting at a wide spacing and consequently considering not to use chemical pesticides. Introduction of power weeder for weed control and paddy-upland crop rotation reduced the cost of production for farming. The crop pattern and method of land us such as mix cropping, crop rotation and conversion of paddy field-upland fieldd were appeared to be very important in organic agriculture. The organic agricultural techniques get systematized upon the adaptation the regional ecology and the development of skills of the farmer. The most important point to achieve the success in organic agriculture system is not only by the development of the technical matters but also by the building of healthy relation and understandings between producers and consumers.

• International Journal of Aeronautical and Space Sciences
• /
• v.14 no.1
• /
• pp.91-98
• /
• 2013

The rigorous requirements of modern spacecraft missions necessitate a precise attitude determination strategy. This paper mainly researches that, based on three space-borne attitude sensors: 3-axis rate gyros, 3-antenna GPS receiver and star-sensor. To obtain global attitude estimation after an information fusion process, a feedback-involved Federated Kalman Filter (FKF), consisting of two subsystem Kalman filters (Gyros/GPS and Gyros/Star-sensor), is established. In these filters, the state equation is implemented according to the spacecraft's kinematic attitude model, while the residual error models of GPS and star-sensor observed attitude are utilized, to establish two observation equations, respectively. Taking the sensors' different update rates into account, these two subsystem filters are conducted under a variable step size state prediction method. To improve the fault tolerant capacity of the attitude determination system, this paper designs malfunction warning factors, based on the principle of ${\chi}^2$ residual verification. Mathematical simulation indicates that the information fusion strategy overwhelms the disadvantages of each sensor, acquiring global attitude estimation with precision at a 2-arcsecs level. Although a subsystem encounters malfunction, FKF still reaches precise and stable accuracy. In this process, malfunction warning factors advice malfunctions correctly and effectively.

• Smart Structures and Systems
• /
• v.3 no.2
• /
• pp.201-217
• /
• 2007

An active damage detection technique is introduced to locate damage in an isotropic plate using Lamb waves. This technique uses a time-domain energy model of Lamb waves in plates that the wave amplitude inversely decays with the propagation distance along a ray direction. Accordingly the damage localization is formulated as a least-squares problem to minimize an error function between the model and the measured data. An active sensing system with integrated actuators/sensors is controlled to excite/receive $A_0$ mode of Lamb waves in the plate. Scattered wave signals from the damage can be obtained by subtracting the baseline signal of the undamaged plate from the recorded signal of the damaged plate. In the experimental study, after collecting the scattered wave signals, a discrete wavelet transform (DWT) is employed to extract the first scattered wave pack from the damage, then an iterative method is derived to solve the least-squares problem for locating the damage. Since this method does not rely on time-of-flight but wave energy measurement, it is more robust, reliable, and noise-tolerant. Both numerical and experimental examples are performed to verify the efficiency and accuracy of the method, and the results demonstrate that the estimated damage position stably converges to the targeted damage.