• Journal of information and communication convergence engineering
• /
• v.8 no.4
• /
• pp.365-369
• /
• 2010

In this paper, a novel notch resonator is proposed based on Rectangular Split Ring Resonator (RRSS) element. We represented the electrical characteristics for R-SRR elements coupled with microstrip line, and measured result is compared with electromagnetic simulation (HFSS) result. We also solved equivalent circuit for R-SRR element, and also discussed influences of change structural parameters of R-SRR. The size of R-SRR is the most important parameters for frequency tuning. Also we can make tunable resonator form the basic structure. This novel resonator can apply to design of tunable bandpass filter and voltage control oscillator.

• Journal of the Korean institute of surface engineering
• /
• v.31 no.5
• /
• pp.245-250
• /
• 1998

There is clear pressing need to reduce bias field(Ha,) used on linear magenetomechanical resonator tag by at least a factor of two to allow low-bias operation near the frequency minimum since reducing Ha causes a dramatic increase in well depth, which implies increased stability. However, this makes it more difficult to maintain tight frequncy specs. It can be solved by a reduction of magnetomechanical coupling(k). We determined from an equivalent circuit model that optimal reduced, k, is near 0.3 Also, We determiend the material properties($lambda_s$, :saturated magenetostriction, $M_s$, and,$H_a$) that give k=0.3. From these evaluations, we suggested that on optimal comosition with adequate mathrial properties is $Fe_{55}Co_{15}Cr_6Nb_2B_{18}Si_4$.

• Korean Journal of Optics and Photonics
• /
• v.16 no.3
• /
• pp.266-274
• /
• 2005

We have designed photonic crystal based bandpass filters whose characteristics are suitable for WDM communication system. The filters consist of coupled point defect resonators in two-dimensional photonic crystal. The frequency response of coupled resonators has been analyzed by the coupling of modes in time, from which the design parameters for the coupled resonator filters have been extracted. For the appropriate choice of the design parameters, each resonator is treated as a lumped L-C resonance circuit, and from the analogy between the equivalent circuit and the standard L-C filter circuits, the design parameters are simply determined from the table for general filter circuit design. Based on the determined design parameters, a photonic crystal based filter has been designed and its performance has been calculated using the finite-difference time-domain method. The designed filter shows a pass band of 50GHz and 0.5 dB in-band ripple, which is suitable for typical WDM communication systems with 100GHz channel spacing.

• Transactions on Electrical and Electronic Materials
• /
• v.7 no.4
• /
• pp.196-203
• /
• 2006

An air-gap type FBAR was designed using Leach equivalent model for analyzing a vertical structure of the FBAR. For the top electrode, Pt, and the bottom electrode, Au, of $1.2{\mu}m$ thickness and the piezoelectric of 0.8,urn thickness, the resonance and anti-resonance occurred at 2.401 GHz and 2.460 GHz, respectively. $S_{11}$ was increased and $S_{21}$ was decreased as the resonance area of FBAR was widened. We observed the characteristics of insertion loss, bandwidth and out-of-band rejection of ladder-type FBAR BPF by changing resonance areas of series and shunt resonators and by adding stages. As the resonance area of series resonator was increased, insertion loss was improved but out-of-band rejection was degraded. And as the resonance area of shunt resonator was increased, insertion loss was degraded a little but out-of-band rejection was improved even without adding stages. We, also, changed the shape of the resonance area from square shape to rectangle shape to examine the effects of the resonator shape on the characteristics of the BPF. The best performances were observed when the sizes of series and shunt resonator are $150{\mu}m{\times}l50{\mu}m\;and\;5{\mu}m{\times}50{\mu}m$, respectively. Out-of-band rejection was improved about 10dB and bandwidth was broadened from 30MHz to 100MHz utilizing inductor tuning on $2{\times}2\;and\; 4{\times}2$ ladder-type BPFs.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.25 no.11
• /
• pp.1128-1134
• /
• 2014

In this paper, the effects of a metamaterial slab with negative permeability in a magnetically coupled wireless power transfer system (WPT) in the overall performance are analyzed quantitatively in terms of the effective quality factors of the loop resonators and coupling coefficient considering the slab losses, based on an equivalent circuit. Using the ideal metamaterial slab(lossless slab), the WPT efficiency is improved considerably by the magnetic flux focusing. However, the practical lossy slab made of RRs or SRRs limits the significant enhancement of WPT efficiency due to the relatively high losses in the slab consisting of RRs or SRRs near the resonant frequency. For the practical loop resonator, other than a point magnetic charge, using the practical lossy metamaterial slab in order to improve the transfer efficiency, the width of the slab needs to be optimized somewhat less than the half of the distance between two loop resonators. For the low-loss slab with its loss tangent of 0.001, the WPT efficiency is maximized at 93 % when the ratio of the slab width and the distance between the two resonators is approximately 0.35, compared with 53 % for the case without the slab. The efficiency in case of employing the high-low slab(loss tangent: 0.2) is maximized at 61 % when the slab ratio is 0.25.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.28 no.8A
• /
• pp.620-625
• /
• 2003

The coplanar waveguide bandpass filter using folded-line stepped-impedance resonators(SIRs) is proposed. The folded-line SIR has about λ/8 length using the short-circuited end on coplanar waveguide. It make that the bandpass filter has the half size in comparison with general λ/4 SIR filter. In this paper, we derive the equivalent circuit and design the bandpass filter by using that. We design and fabricate the bandpass filter which has 5 GHz center frequency and 3 % fractional bandwidth. The measurement results fur 4-pole folded SIR bandpass filter agreed well with full-wave simulation and equivalent circuit results. The fabricated bandpass filter has a good spurious characteristic, which the harmonic frequency appeared at 2.5f$\_$0/). The proposed folded-line SIR bandpass filter are applicable for MMIC and High-Tc superconducting filters. bandwidth.

• Proceedings of the KIEE Conference
• /
• 2004.07c
• /
• pp.2014-2016
• /
• 2004

In order to obtain a low-loss ferroelectric phase shifter, the reflection-type phase shifter with ferroelectric defected ground structure (DGS) resonators has been designed in this paper. The proposed phase shifter is consist of a 3-dB $90^{\circ}$ branch-line hybrid coupler and terminated reflective circuit with tunable ferroelectric DGS resonator. The ferroelectric DGS unit structure can provide high Q resonator characteristic at high frequencies. The design parameters of equivalent circuit for the tunable DGS resonator are derived by using simple circuit analysis method and three-dimensional full wave finite element method. The fabricated phase shifter has an insertion loss of better than 3.4dB at 13.5GHz.

• Journal of the Korean Ceramic Society
• /
• v.40 no.10
• /
• pp.961-966
• /
• 2003

A Multi-Layer Ceramic (MLC) chip type Band-Pass Filter (BPF) using BiNb$\_$0.975/Sb$\_$0.025/ $O_4$ LTCC (Low Temperature Co-fired Ceramics) and MLC processing is presented. The MLC chip BPF has the benefits of low cost and small size. The BPF consists of coupled stripline resonators and coupling capacitors. The BPF is designed to have an attenuation pole at below the passband for a receiver band of IMT-2000 handset. The computer-aided design technology is applied for analysis of the BPF frequency characteristics. The attenuation pole depends on the coupling between resonators and the coupling capacitance. An equivalent circuit and structure of MLC chip BPF are proposed. The frequency characteristics of the manufactured BPF is well acceptable for IMT-2000 application.

• Journal of Astronomy and Space Sciences
• /
• v.24 no.4
• /
• pp.397-408
• /
• 2007

Diplexer is one of core devices needed to communicate with satellite using single ground antenna by separating uplink and downlink signal. This paper presents the design of the S-band diplexer for LEO TT&C application, especially for KOMPSAT (KOrea Multi-Purpose SATellite). To cope with requirements such as high handling power, low insertion loss, air-cavity resonator with high quality factor was considered as one of design drivers. Design was started with predicting unloaded Q and equivalent circuit from the structure of air-cavity resonator. For the convenience of adjustment, the coupling factor placed between resonators was estimated from COTSEM (Electro-Magnetic) simulator, EESOF $ADS^{TM}$, and expressed with 2-order polynomial regression. To improve the isolation between transmitting part (Tx) and receiving part (Rx), the inductive and capacitive attenuation poles were inserted between $4^{th}\;and\;6^{th}$ resonator respectively. The fabricated diplexer consists of two bandpass filters and each filter has eight resonants. From the measurement, it was shown that major requirements such as 0.5dB of insertion loss, 20dB of return loss and 100dB of isolation were fully satisfied within passband.

• Journal of Advanced Navigation Technology
• /
• v.25 no.1
• /
• pp.90-95
• /
• 2021

In this paper, the design method for a high-sensitivity compact resonator for chipless RFID tags is proposed. Proposed high-sensitivity compact resonator uses an interdigital-capacitor structure instead of a capacitor-shaped strip structure in a conventional ELC resonator. The length of the electrode plate of the IDC structure is longer than that of the conventional capacitor-shaped structure, resulting in a larger equivalent capacitance of the resonator. This can lower the resonant peak frequency of the RCS characteristic. Two resonators with the same length of the square loop and the width of the strip are fabricated on an RF-301 substrate with a thickness of 0.8 mm. The experiment results show that the resonant peak frequency and value of the bistatic RCS for the ELC resonator were 4.305 GHz and -30.39 dBsm, whereas those of the proposed IDC resonator were 3.295 GHz and -36.91 dBsm. Therefore, the size of the resonator is reduced by 23.5% based on the measured resonant peak frequency of the RCS characteristic.