• International Journal of Naval Architecture and Ocean Engineering
• /
• 제10권4호
• /
• pp.458-467
• /
• 2018

Efforts have been made in this paper to develop the measuring device for the insulation performance of full scale NO96 LNG CCS. The facility was designed to maintain environmental conditions which are similar to operation conditions of full scale LNG CCS. In the facility, the heat sink boundary was kept cryogenic temperature by cold chamber which contains liquefied nitrogen and heat source boundary was made by external case heated by natural convection. Heat Flow Meter method (HFM) was applied to this facility, hence Heat Flux Sensors (HFS) were attached to specimen. The equivalent thermal conductivity of full scale NO96 unit box was targeted to measure and PUF of same size was used for the calibration test. Additionally, the finite element analysis was carried out to check the performance of the developed test facility and experimental results were also compared with those predicted by the numerical method.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2001년도 봄 학술발표회 논문집
• /
• pp.167-174
• /
• 2001

Reflection method using ultrasonic source has been attempted to obtain the information about tunnel lining structures composed of lining, shotcrete, water barrier and voids at the back of lining. In this work, two different types of sources, i.e. single-pulse source and sweep source, can be used. Single-pulse source with short time duration has the frequency content whose amplitudes tend to be concentrated around the dominant frequency, whereas sweep source with long time duration denotes a flat distribution of relatively larger amplitude over a broad frequency band, although the peak to peak amplitude of single-pulse source wavelet is equivalent to that of sweep source one. In traditional seismic application, a single-pulse source(weight drop, dynamite) is typically used. However, to investigate the fine structure, as it is the case in the tunnel lining structure, the sweep wavelet can be also a desirable source waveform primarily due to the higher energy over a broad frequency band. For the investigation purposes of sweep source, a physical modeling is a useful tool, especially to study problems of wave propagation in the fine layered media. The main purpose of this work was using a physical modeling technique to explore the applicability of sweep source to the delineation of inner layer boundaries. To this end, a two-dimensional physical model analogous to the lining structure was built and a special ultrasonic sweep source was devised. The measurements were carried out in the sweep frequency range 10 ∼ 60 KHz, as peformed in the regular reflection survey(e.g. roll-along technique). The measured data were further rearranged with a proper software (cross-correlation). The resulting seismograms(raw data) showed quitely similar features to those from a single-pulse source, in which high frequency content of reflection events could be considerably emphasized, as expected. The data were further processed by using a regular data processing system "FOCUS" and the results(stack section) were well associated with the known model structure. In this context, it is worthy to note that in view of measuring condition the sweep source would be applied to benefit the penetration of high frequency energy into the media and to enhance the resolution of reflection events.

• 전기학회논문지
• /
• 제63권1호
• /
• pp.42-47
• /
• 2014

The use of BLDC motor in Vehicle and industrial field, it is operated by continuous and intermittent driving. When the intermittent driving is occurred by the rise and fall of temperature repeatedly, it was represented by different characteristics in case of continuous driving. So, it is very important that heat source estimation according to the duty ratio. In this paper, temperature characteristics according to the operating method of BLDCM was calculated by using the thermal equivalent circuit, and the validity of the study was demonstrated as compared to the calculated and experimental results.

• ETRI Journal
• /
• 제22권1호
• /
• pp.38-46
• /
• 2000

The extraction of model parameters for embedded passive components is crucial for designing and characterizing the performance of multichip module (MCM) substrates. In this paper, a method for optimizing the extraction of these parameters using genetic algorithms is presented. The results of this method are compared with optimization using the Levenberg-Marquardt (LM) algorithm used in the HSPICE circuit modeling tool. A set of integrated resistor structures are fabricated, and their scattering parameters are measured for a range of frequencies from 45 MHz to 5 GHz. Optimal equivalent circuit models for these structures are derived from the s-parameter measurements using each algorithm. Predicted s-parameters for the optimized equivalent circuit are then obtained from HSPICE. The difference between the measured and predicted s-parameters in the frequency range of interest is used as a measure of the accuracy of the two optimization algorithms. It is determined that the LM method is extremely dependent upon the initial starting point of the parameter search and is thus prone to become trapped in local minima. This drawback is alleviated and the accuracy of the parameter values obtained is improved using genetic algorithms.

• 한국전자파학회논문지
• /
• 제9권5호
• /
• pp.567-577
• /
• 1998

유한차분 시간영역 방법을 이용하여 연속 및 불연속 마이크로스트립올 해석할 때 홉수 경계조건은 Berenger의 완전 접합충(Perfectly Matched Layer:PML)올 3차원으로 적용하고, 전원의 인가는 기존의 마이크로스트립 전면(front face)에 인가하는 방법 대신 내부전원(Inner Source Technique:IST)을 이용하였다. 이 방법을 이용하면 de성분의 왜곡이 개선되고, 에베네센트(evanescent) 및 복사 전자계가 존재하는 측면과 윗면의 계산 영역올 줄이더라도 해석된 특성은 신뢰할 수 있는 결과를 얻올 수 있었다. 또한 내부전원의 위치를 조정함으로서 불완전한 경계조건에 의해서 발생되는 반사파의 영향올 효과적으로 제거할 수 있었다. 본 연구에서는 이러한 방법을 이용하여 마이크로스트립의 분산특성 및 특성임피던스를 계산하였다. 그리고 종단개방 마이크로스트립의 산란계수의 크기와 위상올 구하고 그 동가회로를 계산하였다.

• 전기학회논문지
• /
• 제68권2호
• /
• pp.262-268
• /
• 2019

Previous dynamic models of hysteresis motor use an extended induction machine equivalent circuit or somewhat different equivalent circuit with conventional one, which makes unsatisfiable results. In this paper, the hysteresis dynamic characteristics of the motor rotor are analyzed using the inverse Preisach model and the hysteresis motor equivalent circuit considering eddy current effect. The hysteresis loop for the rotor ring is analyzed under full-load voltage source static state. The calculated hysteresis loop is then approximated to an ellipse for simplicity of dynamic computation. The permeability and delay angle of the elliptic loop apply to the dynamic analysis model. As a result, it is possible to dynamically analyze the hysteresis motor according to the applied voltage and the rotor material. With this method, the motor speed, generated torque, load angle, rotor current as well as synchronous entry time, hunting effect can be calculated.

• Journal of electromagnetic engineering and science
• /
• 제2권2호
• /
• pp.81-86
• /
• 2002

This paper presents the full wave analysis of microwave circuits with nonlinear device using the finite difference time domain method. The equivalent current source is used to model nonlinear device and all the electric field components at the nonlinear device are updated by FDTD algorithm. The currents and voltages of nonlinear device are calculated by the state equations and iteration method. To validate the proposed method, the S-parameters of NEC NE72089 MESFET in various conditions are analyzed and the results are compared with those of the ADS. The proposed method is applied to the analysis of a microwave amplifier, which includes NEC NE72089 MESFET. The analysis results obtained by the present method show good agreement with those of the ADS.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2005년도 ICCAS
• /
• pp.1482-1485
• /
• 2005

An equivalent schema matching among several different source schemas is very important for information integration or mining on the XML based World Wide Web. Finding most similar source schema corresponding mediated schema is a major bottleneck because of the arbitrary nesting property and hierarchical structures of XML DTD schemas. It is complex and both very labor intensive and error prune job. In this paper, we present the first complex matching of XML schema, i.e. XML DTD, inlining two dimensional DTD graph into flat feature values. The proposed method captures not only schematic information but also integrity constraints information of DTD to match different structured DTD. We show the integrity constraints based hierarchical schema matching is more semantic than the schema matching only to use schematic information and stored data.

• 대한기계학회논문집
• /
• 제18권7호
• /
• pp.1789-1798
• /
• 1994

This paper aimed for numerical simulation of complicated gas turbine combustor with swirler. For the convenience of numerical analysis, fuel nozzle and air linear hole areas of secondary and dilution zone, which are issued to jet stream, were simplified to equivalent areas of annular type. In other to solve these problems, imaginary source terms which are corresponded to supplied fuel amount were added to those of governing equation. Chemical equilibrium model of infinite reaction rate and $k-{\epsilon}-g$ model with the consideration of density fluctuation were applied. As the result, swirl intensity contributed to mixing of supplied fuel and air, and to speed up the flame velocity than no swirl condition. Temperature profiles were higher than experimental results at the upstream and lower at the downstream, but total energy balance was accomplished. As these properties showed the similar trend qualitatively, simplified simulation method was worth to apply to complicated combustor for predicting combustion characteristics.

• 한국공작기계학회논문집
• /
• 제17권3호
• /
• pp.122-127
• /
• 2008

The source of wayside noise for the train are the aerodynamic noise, wheel/rail noise, and power unit noise. The major source of railway noise is the wheel/rail noise caused by the interaction between the wheels and rails. The Structure borne noise is mainly a low frequency problem. The train noise and vibration nearby the elevated railway make one specific issue. The microphone array method is used to search sound radiation characteristics of elevated structure to predict the noise propagation from an elevated railway. In this paper, the train noise and structure borne noise by train are measured. From the results, we investigated the effect on the sound absorption tunnel for elevated railway.