• Advances in aircraft and spacecraft science
• /
• v.4 no.6
• /
• pp.679-699
• /
• 2017

The aim of this study is to perform a finite element analysis of the Von Mises stresses distribution in the adhesive layer and of the J-Integral for a damaged plate repaired by a composite patch. Firstly, we study the effect of the fiber orientation, especially the position of the layers that have orientation angle different of $0^{\circ}$ from the first layer which is in all cases of our study oriented at ($0^{\circ}$) on the J-Integral. Secondly, we evaluate the effects of the mechanical properties of the patch and the use of a hybrid patch on the reduction of stresses distribution and J-Integral. The results show clearly that the stacking sequence for the composite patch must be selected to absorb optimally the stresses from the damaged area and to position the various layers of the composite under the first layer whose fibers orientation will remain in all cases equal to $0^{\circ}$. The use of a hybrid composite reduces significantly the J-Integral and the stresses in both damaged plate and the adhesive layer.

• 한국연소학회:학술대회논문집
• /
• 2014.11a
• /
• pp.101-102
• /
• 2014

Rising oil price and environmental problems are causing automotive industry to increase fuel efficiency. Improved fuel efficiency in gasoline engine was made possible by development of DISI gasoline engine. Since fuel is injected inside cylinder directly, in-cylinder temperature can be reduced than multi-port injection engine and this leads to increased compression ratio. However, engine performance is largely dependent on mixture formation process due to in-cylinder fuel injection. Especially for spray guided and air guided DISI gasoline engine, injection direction is important factor to mixture preparation. It is because interaction between intake flow and spray affect fuel-air mixture. Hence, in this study, mixture formation characteristics were analyzed by varying injection direction using KIVA 3V release2 code. Residual gas was considered for assuming combustion. Therefore, initial condition for in-cylinder temperature was set equal to the end state of exhaust stroke of combustion cycle. Since angle between intake air flow direction and spray direction affects fluid flow and evaporation field, mixture distribution was affected by fuel injection direction dominantly.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.9 no.2
• /
• pp.153-162
• /
• 1997

In this study, the wet surface heat transfer coefficients and friction factors of the heat exchanger with slit-wavy fin were measured. Four sample cores of two or three row with fins of 12 fpi or 16 fpi were tested. Tests were conducted in a closed loop wind tunnel, where the heat exchanger was mounted at 45 degree inclination angle. The wet surface heat transfer coefficient was reduced following the procedure given in ARI 420-81. During the course, new definitions of the $\varepsilon$-NTU applicable to enthalpy driving system were introduced. The wet surface heat transfer coefficients were approximately equal to the dry surface values. However, the friction factors were approximately 120% to 170% higher than those of the dry surface. Both the heat transfer coefficient and the friction factor of the wet surface increased as the relative humidity increased, fin pitch decreased, and the number of row decreased, although the difference was not large.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.16 no.1
• /
• pp.112-121
• /
• 1992

A numerical analysis was carried out to study two-dimensional turbulent natural convection in a square enclosure containing fluid of Prandtl number 6.05 within internal energy sources. The square enclosure was bounded by four rigid planes of constant equal temperature. Inclination angles of 0, 15, 30 and 45 deg. from the horizon for Rayleigh numbers from 1 * 10$^{6}$ to 1 * 10$^{9}$ were studied. Local and average Nusselts numbers are obtained on all four walls. If inclination angle exists, the average Nusselt number appears in increasing order at bottom, left, right and top wall.

• Proceedings of the KSRS Conference
• /
• 2002.10a
• /
• pp.663-663
• /
• 2002

The National Oceanographic Research Institute of KOREA started to survey for the basic data necessary to territorial sea and EEZ identification and marine development with Multi-Beam Echo Sounder(L3 SeaBeam 2112) since 1996. The Multi-Beam surveys has provided a very new and precise way of describing the morphology and nature of the underwater seabed. Multi-Beam Echo Sounder systems employ sound waves propagating at angles which vary from vertical to nearly horizontal. The locations on the bottom where echoes are generated cover a swath whose port to starboard width may be equal to many times the water depth. Newer Multi-beam bathymetric sonars provide both a beam by beam depth and backscatter amplitude of the bottom. But The backscattered amplitude didn't use for identification of bottom properties because backscatter amplitude effects by the many environmental variables of underwater and seabed. We investigates the utilization of geo-referenced backscatter amplitude and analysis of relationship between The Backscattered Amplitude and Sidescan Sonar imagery from Sea Beam 2112. For the backscattered amplitude imagery mainly represents the properties of sediment, we computed the beam geometry, time-varied amplifier gain, and mainly incidence angle to the topography using bathymetric model at each ping. In this paper, those issues are illustrated, and the angular independent imagery based on swath topographic model is described.

• Computational Structural Engineering
• /
• v.9 no.4
• /
• pp.135-140
• /
• 1996

Single angle or channel with thin-walled open section can be used as compression member for example as web member in truss. In this case the inevitable eccentricity due to fabrication is commonly neglected in structural design. However eccentricity effect should be considered in the member design, especially in case of compression member. The critical loads of compression members that buckle by twisting or by a combination of bending and twisting are to be determined by solving governing differential equations. In this paper, the investigations are limited to the rolled channels([), equal-leg angles(L), lipped channels(C) and the applied loads are assumed to have some eccentricities.

• Tunnel and Underground Space
• /
• v.11 no.4
• /
• pp.311-318
• /
• 2001

RQD is used to evaluate the degree of fracture in the rock mass and is also used as input into rock mass classification scheme, such as RMR and Q-system. However there are some drawbacks of the RQD caused by anisotropy and calculation length. Thus it is important to understand the variation of RQD in 3-D space in order to evaluate the properties of rock mass. The main purpose of this study is to reveal the distribution of RQD in the equal-angle stereo net, to investigate the effects of scanline length and joint frequency and to inquire the effect on the selection of rock mass strength parameters in the numerical analysis. Analysis has been extended to field joint survey data using same method. The results can be applied to contribute for more accurate interpretation of the results of engineering geological survey for better design and construction work.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.7 no.2
• /
• pp.161-167
• /
• 1983

In this study the phenomenon of cutting stress which arises on cutting tools and work pieces in cutting process is investigated by rake angle of cutting tools and feed for this measurement, P$_{s}$-1 (high modulus, photolastic Inc.) was used as a cutting tool, P$_{s}$-3 (medium modulus, photolastic Inc.) was used as work piece and reduction apparatus was attached to the head stock, and orthogonal cutting was adapted as a cutting method and transparent glass was used to block the strain in the orientation of thickness. The followings are the results of this study. (1) Photoelastic experimental equipments have made it possible to make dynamic measurement and analyze stress distribution in cutting tool and work piece surface which has hitherto been conducted only in static measurement and analyzing method. (2) The maximum stress arising at tools and work pieces in cutting process is on the tool edge tip, and the maximum stress arising on the tip of cutting tools is equal to that on the contacting area of work pieces in values. (3) The distributions of maximum shear stress on certain parts of the cutting tools and work pieces are as follows; for cutting tools, .alpha.=12.deg., .alpha.=0.deg., .alpha.=-12.deg. in order, and for work pieces, .alpha.=-12.deg., .alpha.=0.deg., .alpha.=12.deg. in opposite order.der.

• 한국전산유체공학회:학술대회논문집
• /
• 2004.10a
• /
• pp.47-51
• /
• 2004

Accurate Prediction of a supersonic missile base drag continues to defy even well-rounded CFD codes. In an effort to address the accuracy and predictability of the base drags, the influence of grid system and competitive turbulence models on the base drag is analyzed. Characteristics of some turbulence models is reviewed through incompressible turbulent flow over a flat plate, and performance for the base drag prediction of several turbulence models such as Baldwin-Lomax(B-L), Spalart-Allmaras(S-A), $\kappa-\epsilon$, $\kappa-\omega$ model is assessed. When compressibility correction is injected into the S-A model, prediction accuracy of the base drag is enhanced. The NSWC wind tunnel test data are utilized for comparison of CFD and semi-empirical codes on the accuracy of base drag predictability: they are about equal, but CFD tends to perform better. It is also found that, as angle of attack of a missile with control (ins increases, even the best CFD analysis tool we have lacks the accuracy needed for the base drag prediction.

• The Korean Journal of Zoology
• /
• v.6 no.1
• /
• pp.15-20
• /
• 1963

The characteristics of the pharyngeal bones and their teeth in Korean Cyprinids fishes, as a rule, are summarized as follow : 1. The materials 13 genera and 17 species from Nak Dong River. 2. Breadth of bone about 2.8(Cyprinus carpio) to 4.9(Culter brevicauda) in bone length. Length of bone about 8.5(Carassius carassius ) to 20.2 (Pseudogobio esocinus ) in body length. Breadth of pitted surface about 66%(Carassius carassius) to 85%(Acanthorhodeus asmussi ) of breadth of bone. 3. The position and distinct ratio of anterior angle correlated. 4. Posterior limb always longer than anteriro, but posterior edentulous process not shorter than anterior's or equal. 5. Zacco platypus with pitted surface on anterior limb , but Z.temmincki without it. 6. Teeth one to three rowed in accordance with the differences of each genus : a. one rowed genera ..... Carassius , Pseudorasbora, Sarcocheilichthys (Sakiyae), Pungtungia, Acheilognathus, Acanthorhodeus. b. two rowed genera ........ Pseudogobio, Gnathopogon, Tribolodon. c. Three rowed genera .... Cyprinus, Hemibarbus, Zacco , Culter 7. Teeth of main (primary ) row with four or five teeth is symmetrized exceptive three genera (Tribolodon, Zacco, Culter). 8. Grinding surface and bill type correlated. 9. In Acheilognathus, A.Yamatsutae have one or two indistinct serration but each individual is unlike.