• 한국지반공학회논문집
• /
• 제32권11호
• /
• pp.61-72
• /
• 2016

구조물의 고층화가 진행됨과 동시에 효율적인 기초 설계를 위해 대구경 PHC 말뚝의 사용이 증가하고 있으며, 특히 600mm PHC 말뚝의 사용량이 급증하고 있다. 본 연구에서는 현재 사용되고 있는 설계법의 적정성을 평가하기 위하여, 직경 600mm PHC 매입말뚝에 대하여 수행된 46본의 동재하시험 결과를 분석하였다. 선단지지력은 초기항타시험의 결과를 이용하였으며 주면마찰력은 재항타시험 결과를 이용하여 각각의 허용지지력을 산정하였다. 동재하시험으로부터 산정된 허용지지력을 현재 사용되는 설계법으로 평가된 허용지지력과 비교하였다. 분석결과, 동재하시험으로 산정된 허용선단지지력은 대부분의 말뚝에서 설계기준보다 컸지만, 허용주면마찰력은 많은 말뚝에서 설계기준보다 작게 산정되었다. 이와 같은 큰 선단지지력과 작은 주면마찰력은 천공장비의 성능 향상 및 굴착 깊이의 증가 때문이며 이로 인해 전체지지력에서 선단지지력이 차지하는 비율이 높아졌기 때문이다.

• 한국지반공학회논문집
• /
• 제29권1호
• /
• pp.61-70
• /
• 2013

본 연구에서는 2차원 유한차분 해석을 이용하여 절리암반에 시공된 말뚝기초의 선단지지력을 분석하였다. 이를 위해 암반의 절리상태를 고려할 수 있는 Hoek-Brown 항복규준을 이용하여 다양한 조건의 수치해석이 수행되었다. 넓은 범위의 절리상태를 고려하기 위하여 GSI를 주 매개변수로 설정하였고 말뚝 직경, 암반의 일축압축강도, Hoek-Brown 상수 $m_0$의 매개변수 영향을 살펴보았다. 본 연구결과 매개변수들의 변화에 따른 절리 암반에 설치된 말뚝기초의 선단지지력 변화 경향을 확인하였고 이러한 결과를 토대로 매개변수 분석에 따른 선단지지력 결과를 도출하였다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2009년도 세계 도시지반공학 심포지엄
• /
• pp.884-890
• /
• 2009

The bi-directional pile load test with variable end plate overcomes the shortcoming of the Osterberg cell test. It is possible that the ultimate bearing capacity of the bi-direction can be known by using the loading of the end plate and two step procedures. The first step is to confirming end bearing capacity with variable end plate and the second step is similar to the conventional O-cell test. In the study, To calculate ultimate capacity of bi-directional load test using model with the pile with variable end plate O-cell, operated with end plate of 3 type on sand layer according to the relative density, loose, medium and dense conditions.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2010년도 춘계 학술발표회
• /
• pp.415-426
• /
• 2010

Post-grouting for the drilled shaft is known to increase the end bearing capacity of pile 2~3 times higher by consolidating and reinforcing the disturbed ground containing slime around the pile end. However, the general design guideline for post-grouting has not been established yet in Korea. Especially in the domestic application, the post-grouting is employed just for repairing the pile with the unacceptable resistance rather than for increasing the design resistance of pile. Therefore, little is reported about the effect of post-grouting on the pile resistance itself. In this study, the effect of post-grouting on the resistance of drilled shafts installed in the weathered rock in Korea was estimated by performing the bi-directional load tests on the piles with and without the post-grouting. The test results presented that the initial slope of end bearing-base displacement curve in the pile with post-grouting was 4 times higher than that without post-grouting. At the acceptable settlement (1% of pile diameter), the end bearing capacities of piles with and without the post-grouting were estimated to be 12.0 MPa and 7.0 MPa, respectively, indicating that the post-grouting could increase the end bearing resistance of pile in weathered rock more than 70%.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2010년도 춘계 학술발표회
• /
• pp.1088-1093
• /
• 2010

The Smart bi-directional pile load test with variable end plate overcomes the shortcoming of the Osterberg cell test. It is possible that the ultimate bearing capacity of piles can be known by using two different end plates. The first step is to measure end bearing capacity with smaller end plate and the second step is similar to the conventional O-cell test. In this study, model test was performed to evaluate the smart bi-directional pile load test in sand. Vertical displacement of the model pile were messured at the axial loading condition.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2008년도 추계 학술발표회
• /
• pp.407-426
• /
• 2008

The bentonite slurry has been used as the stabilize suspension for wet process bored pile construction in Thailand. The bentonite suspension has benefit on filtration in the sand layer, but it creates thick cake film along pile shaft and loose sedimentation at pile toe. The base grouting technique was widely used to rectify the soft base or loose sedimentation problem of bored pile. The base grouting technique was not increased only end bearing capacity, but was also more increase in skin friction capacity of the bored piles. The comprehensive researches on base grouting was carried out by installing PVC casing inside the shaft to allow the drilling through the pile base in order to collect the soil sample below the pile tip. The polymer based slurry recently was used to replace the bentonite slurry to overcome the thick cake film along pile shaft as well as loose sedimentation at pile toe. The extent research on polymer slurry by physical model was performed to verify the real behavior of polymer. The appropriate mixing ratio of polymer was proposed. The design skin friction coefficient, $\beta$ and end bearing coefficient, Nq, for sand layer base on fully instrumented tested pile were proposed. The application on remedial of the lose capacity bored pile with large displacement in Bangladesh was proposed and discussed.

• 한국지반환경공학회 논문집
• /
• 제23권12호
• /
• pp.5-15
• /
• 2022

이중 강-콘크리트 합성말뚝의 설계를 위한 지지력 평가 방법이 정립되지 않아 기존 강관말뚝 설계 지지력식이 활용되고 있다. 그러나 이들 설계식 간 지지력 예측 결과가 상이할 뿐만 아니라 일반적으로 가장 보수적인 결과를 채택하게 된다. 이러한 말뚝 지지력 평가방법은 설계의 신뢰성 및 경제성을 낮추게 된다. 본 논문은 수직하중을 받는 이중 강관 내 콘크리트 채움된 신형식 합성단면(DSCT) 말뚝의 역학적 거동을 수치해석적으로 조사하고, 여러 DSCT 말뚝 조건변화에 따른 연직지지력을 분석하였다. DSCT 말뚝 및 인접지반에 대한 축대칭 유한요소모델을 생성하였고, 이를 활용해 근입깊이, 말뚝 선단 채움재 강성, 말뚝 선단 채움재 높이, 기반암층 종류 변화에 따른 영향을 분석하였다. 또한 해석결과를 말뚝 설계 실무에서 주로 사용하는 선단 지지력 평가식과 비교하여 합성말뚝에 대한 기존 강관말뚝 지지력 산정식의 활용 가능성을 검토하였다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2004년도 춘계학술발표회
• /
• pp.544-551
• /
• 2004

Piles are structural elements made of steel, concrete or timber, and utilize as pile foundation which is one of deep foundations. Driven pile among them, which drives pile into the ground, is fast-constructable, less expensive and it supplies much bearing capacity. For these reasons, its demand is steady. In this study, by selecting the cases which reached ultimate failure during in-situ static loading tests, bearing capacities acquired from these tests were compared with those computed by existing theories and formula. As the results of the analysis, ultimate bearing capacity computed by theoretic formula were less or similar to those of test results in most cases, but lower ground water level and more dense layer where end of piles were reached remarkably high bearing capacity in theoretical methods. ${\beta}-method$ and Korean structure foundation design standard were sensitive to ground physical properties. Meyerhof metbod and API code were relatively independent from site condition.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2009년도 세계 도시지반공학 심포지엄
• /
• pp.545-553
• /
• 2009

A lot of long-span marine bridge, which connects land to island or island to island, are being designed and constructed lately in south-west coast in South Korea. In the past, caisson foundations in marine were mainly adopted in construction and stability aspect, however, nowadays with development of pile construction technology, drilled shaft foundations are mainly adopted. As the long span cable stayed bridge and suspension bridge applied with lots of loads are being designed, the scale of pile foundations are getting larger. As the construction cost of substructure including foundation in marine bridges is too high, the appropriate evaluation of the axial bearing capacity of pile becomes a core factor to decide the construction cost of foundation if the drilled shaft is adopted as foundation type of bridge. The evaluation values of skin friction and end bearing capacity of drilled shaft in weathered rock suggested in south Korea are only to introduce the foreign specifications, and most of them are designed in a kind of hard soil layer. Also the allowable load of pile section is less than the expected bearing capacity of pile in the soil condition since the allowable capacity of pile is undervalued. Recently in order to improve this factor the bi-axial hydraulic load test of pile was taken, the data of load transfer analysis of pile, unit of skin friction and end bearing capacity are accumulated. In our country, the design of piles are made with ASD, however, LRFD considering service, strength and extreme state was adopted in Incheon Grand Bridge implemented with BTL, and the research to systematize the resistance coefficient appropriate at home country are being progressed.

• 한국지반공학회지:지반
• /
• 제9권1호
• /
• pp.31-44
• /
• 1993

말뚝이 설치되는 동안과 하중이 재하되는 동안에 유발되는 관내토의 거동과 관내토가 개단 말뚝의 지지력에 미치는 영향, 그리고 관내토의 하중전이 메카니즘 등을 알아보기 위하여, 개단말뚝의 단면부에 작용하는 지지력과 관내토에 의한 지지력 및 외주면마찰력을 분리하여 측정할 수 있도록 제작된 모형 개단강관말뚝과 압력조절이 가능한 토조를 이용하여 모래지반을 대상으로한 모형말뚝실험을 실시하였다. 실험결과로부터, 개단말뚝의 폐색정도는 폐색길이비(PLR)보다는 특정회수율(${\gamma}$)에 의하여 더 정화히 성의될 수 리음을 알 수 있으며, 내주면마찰력의 대부분은 말뚝 선단부로부터 말뚝내경의 3배까지의 영역에 존재하는 관내토에 의하여 발생되는 것으로 나타났다. 또한 전체 지지력에서 내주면마찰력이 차지하는 비율은 외주면마찰력이 차지하는 비율보다 상당히 크기 때문에, 개단말쪽의 지지력 산정시 내주면마찰력은 필수적으로 고려되어야 한다.