• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.12 no.6
• /
• pp.97-103
• /
• 2003

Currently, due to serious increase of pollution scones, lots of technology has been involved to reduce exhaust gas in diesel engine. But the amounts of exhaust gas can not be decreased somehow due to the increase of diesel vehicles. Moreover, emission standards of each counties are being stringent in advanced countries such as USA and Europe. In the near future, sulfur contents in fuel must be essentially reduced f3r health and environment because sulfur can basically reduce exhaust gas. Therefore, when will be applied to Bio-diesel and ULSD, they could reduce sulfur contents of fuel without aftertreatment and might conform the influence of engine performance, emission, smoke and fuel consumption.

• Journal of Advanced Marine Engineering and Technology
• /
• v.24 no.5
• /
• pp.16-24
• /
• 2000

In this study, using frying oil, performance of engine and emission concentration were compared with the case of using diesel oil. And results are as follows. 1. Engine torque and brake horse power indicate nearly same value as the case of using diesel fuel. 2. Temperature of exhaust gas was increased with as high engine speed and load. 3. To reduce concentration of hydrocarbon, it is effective to operate using used frying oil in low engine speed and load, and adding LPG in high engine speed and load. 4. Concerning with concentration of carbon mono oxide and smoke emission, it was assured, that as engine load increased, lower concentration emitted in case of utilizing mixed fuel than that of utilizing pure diesel fuel.

• Journal of the Korean Society of Industry Convergence
• /
• v.18 no.4
• /
• pp.197-206
• /
• 2015

Recently the automobile engine has been developed in achieving the high performance, fuel economy, and emission reduction. In a conventional spark ignition engine the fuel and air are mixed together in the intake system, inducted through the intake valve into the cylinder, and then compressed. Under normal operating conditions, the combustion is initiated towards the end of the compression stroke at the spark plug by an electric discharge. Following inflammation, a flame develops and propagates through this premixed fuel-air mixture. Therefore the state of mixture is very important in the combustion and emission characteristics. In this study the combustion and emission characteristics were tested and analyzed with changing the mixture composition and engine operating parameters in order to improve the combustion and performance in engine.

• Proceedings of the Korean Society of Agricultural Engineers Conference
• /
• 1999.10c
• /
• pp.405-410
• /
• 1999

This study was performed to find the recycling performance and to provide design data during recycle solid composting system to reduce bulking agent cost, Dairy manure amended with rice hulls and recycled compost was composted in a laboratory -scale vessel by continuous aeration for 10 days. The temperature and ammonia emission variations according to the ratios of bulking agents during the primary aeration stage were surveyed. Also, the influence of fresh compost quality on the recycling performance were anlayzed. While recycled composting system were operatured. The temperature in compost was maintained in the range of 40∼60$^{\circ}C$ needed for biodegradation and death of pathogenic organisms, but the ammonia emission was different by the ratios of recycled compost. The ammonia emission increased due to the low C/N ratio(17.6), high pH value(8.1) of the recycled compost.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.1 no.2
• /
• pp.34-41
• /
• 1993

In order to reduce harmful substances such as particulates and nitric oxides emitted from diesel engine, man kinds of methodology like high pressure spray of diesel fuel oil, exhaust gas recirculation, emulsified fuel usage and dual fuelling have been studied. Dual fuelling of a diesel engine with hydrogen which is well-known as the clean fuel and has excellent combustibility is expected to be effective in reducing harmful substances from diesel engine. This experimental study was conducted to investigate the effect of premixed hydrogen with intake air on the performance and particulate emission characteristics using a single cylinder, prechamber type diesel engine. As a result, it was clarified that a hydrogen-premixed diesel engine can be operated in the state of lower particulate emission and slightly aggravated fuel economy, compared with the conventional diesel engine.

• Journal of Power System Engineering
• /
• v.9 no.3
• /
• pp.5-9
• /
• 2005

A study on the performance and exhaust emissions of diesel engine with reducing exhaust gas temperature is performed experimentally. In this paper, experiments are performed at engine speed 2200rpm, 2600rpm and load 0%, 25%, 50%, 75% and 100% by test engine with F.W. cooler passing through exhaust gas. Main measured & analyzed parameters are exhaust gas temperature, specific fuel consumption, NOx and soot emissions etc. The obtained conclusions are as follows. (1) Specific fuel consumption is the least value at load 75% and it is decreased 1.5% after remodeling F.W. cooler. (2) NOx emission is the most value at load 100% and it is increased 30.1% after remodeling F.W. cooler. (3) Soot emission is the most value at load 100% and it is decreased 20.0% after remodeling F.W. cooler.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1995.11a
• /
• pp.257-260
• /
• 1995

The Field Emission Display promises to improve upon the performance of the traditional CRT, while overcoming the CRTs disadvantages in size and weight which limit its use in portable applications. The technical feasibility of the FED has been reviewed and expeceted to move toward the product development.

• Proceedings of the KSME Conference
• /
• 2007.05b
• /
• pp.3294-3299
• /
• 2007

These days the exhaustion of petroleum resources and environmental problems are getting serious. Many researchers are focused on low emission and high performance vehicles. Therefore, we should concern about emission regulation when we design a new car. In this study, we investigated the characteristics of the traditional mechanical engine cooling systems which control the engine temperature using engine speed and wax type thermostat. This experiment used three components which are Radiator fan, water pump and water valve controlled by an electronic system based on the engine status (load, speed). We elucidated how different between traditional mechanical cooling system and electronic cooling system which control coolant temperature and coolant flow rate in a DI diesel engine in this paper. The results revealed a fuel saving and an emission (CO, HC) reduction on NEDC cycle.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.9 no.5
• /
• pp.23-29
• /
• 2001

This paper is the second of companion papers, which investigate port-masking effects on emission and fuel economy. Port-masking was applied to commercial SOHC 3-valve engine by inserting masking plates between manifold and port. To induce various conditions of stratification, six types of masking plates were applied. In this paper, main interest is focused on the influence of injection timing on emission and fuel economy. Various injection timing was applied to the six cases, under the stoichiometric and lean-limit air-fuel ratio. Under the stoichiometric condition, an explanation about the reason of the change in emission level due to injection timing change is given. It is observed that NOx emission under the LML condition varies significantly when the injection timing changes.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.03a
• /
• pp.43-43
• /
• 2003

Carbon nanotubes(CNTs) have many application points, which are field emission devices, composites, hydrogen storage, nanodevices, supercapacitor and secondary battery. The most promising application point is emitter tip mays of field emission devices. Furthermore, it may be also useful as a vacuum device for high frequency and high power. But, there are some obstacles to fabricate carbon nanotube field emission device. One is that CNTs grown by CVD method has weak adhesion with substrate and the other is non-uniform length of them. These problems are very crucial in aging property and reliability of device in the field emission.