• Proceedings of the KIEE Conference
• /
• 2000.07b
• /
• pp.600-602
• /
• 2000

This paper deals with finite element analysis of 2GVA superconducting generator which has slitted electrothermal shield in d-axis. Open emf voltage is calculated and three phase fault is considered to Predict the generator parameters by F.E.M. Results show that quick response excitation could be applied to superconducting generator with slitted electrothermal shield.

• Journal of Biomedical Engineering Research
• /
• v.24 no.1
• /
• pp.23-29
• /
• 2003

The prevalence of discogenic pain among patients with chronic low back pain is estimated to be about 40%. Lumbar discectomy is being performed as a treatment according to the studies done so far. Recently IDET- Intradiscal electrothermal therapy which is minimally invasive technique is being introduced. This study will investigate important factors of this procedure such as the temperature of heat source, loading times, and the temperature distribution within the intervertebral disc. This study utilized finite element analysis and experiment. It was able to analyze the temperature range of inner intervertebral disc by two mechanisms which are known to alleviate pain clinically. As a result, verification of temperature distribution to 15.6mm($\geq$45$^{\circ}C$) (Mechanism 1-coagulation inner annulus by heat) and 9mm($\geq$6$0^{\circ}C$) (Mechanism 2- contraction inner nucleus by heat) from the heat source was done.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.2 no.4
• /
• pp.259-267
• /
• 2002

We present a novel 3D fabrication method with single X-ray process utilizing an X-ray mask in which a micro-actuator is integrated. An X-ray absorber is electroplated on the shuttle mass driven by the integrated micro-actuator during deep X-ray exposures. 3D microstructures are revealed by development kinetics and modulated in-depth dose distribution in resist, usually PMMA. Fabrication of X-ray masks with integrated electrothermal xy-stage and electrostatic actuator is presented along with discussions on PMMA development characteristics. Both devices use $20-\mu\textrm{m}$-thick overhanging single crystal Si as a structural material and fabricated using deep reactive ion etching of silicon-on-insulator wafer, phosphorous diffusion, gold electroplating, and bulk micromachining process. In electrostatic devices, $10-\mu\textrm{m}-thick$ gold absorber on $1mm{\times}1mm$ Si shuttle mass is supported by $10-\mu\textrm{m}-wide$, 1-mm-long suspension beams and oscillated by comb electrodes during X-ray exposures. In electrothermal devices, gold absorber on 1.42 mm diameter shuttle mass is oscillated in x and y directions sequentially by thermal expansion caused by joule heating of the corresponding bent beam actuators. The fundamental frequency and amplitude of the electrostatic devices are around 3.6 kHz and $20\mu\textrm{m}$, respectively, for a dc bias of 100 V and an ac bias of 20 VP-P (peak-peak). Displacements in x and y directions of the electrothermal devices are both around $20{\;}\mu\textrm{m}$at 742 mW input power. S-shaped and conical shaped PMMA microstructures are demonstrated through X-ray experiments with the fabricated devices.

• The Journal of the Korea Contents Association
• /
• v.22 no.7
• /
• pp.652-662
• /
• 2022

Currently, in the field of spinal surgery around the world, various new technologies have been rapidly developed and applied to patients. The author believes that it is necessary to discuss whether these new technologies are being fully reviewed for efficacy and safety before being applied to patients. To consider this issue, the author analyzed the basic research data and clinical application process of the intradiscal electrothermal therapy, which was developed as a new technology for discogenic pain disease in the 2000s and has been widely used worldwide. As a result, it was found that this procedure has been performed on patients in a state where there is insufficient base research on efficacy and safety. The author judges that this case reveals an essential problem related to the clinical operation of new medical technologies in the field of spine surgery. Therefore, the author believes that in order to minimize the side effects that new medical technology in the field of spinal surgery may have on patients, more full-fledged basic research and higher clinical acceptance standards should be established.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.19 no.6
• /
• pp.1-9
• /
• 2015

This paper introduces a zero-dimensional modeling on the plasma generation in electrothermal gun operation. The plasma generator consists of alumina bore and aluminum electrodes which is electrically powered by outer pulse forming network and, traditionally, its numerical simulations have employed time-dependent one-dimensional governing equations. However, by assuming isothermal approximation along the bore and choked bore exit condition, present analysis simplifies the mass and energy equations into zero-dimensional approximation of plasma conditions coupled with mass ablation model and plasma property evaluation. The numerical results show good agreement with the corresponding one-dimensional computations and thus verify the present modeling approach.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.12 no.3
• /
• pp.76-86
• /
• 2008

The EP(electric propulsion) is unique in that several energy sources can be utilized to produce the electric energy and that high exhaust velocity can be achieved compared to the conventional chemical propulsion. Though a lot of variety of non chemical propulsion are under study, the fact that the EP's specific impulse ranges widely from 200s to 5000s led most research to concentrate on the electric propulsion research. This paper, therefore, is aimed to introduce the up-todate existing EP family such as electrothermal, electrostatic and electromagnetic thrusters where its operating concepts, characteristics and possible variants are presented for future applications.

• Bulletin of the Korean Chemical Society
• /
• v.28 no.4
• /
• pp.553-556
• /
• 2007

We previously reported a 27.12 MHz inductively coupled plasma source at atmospheric pressure for atomic emission spectrometry based on polymer microchip plasma technology. For the PDMS polymer microchip plasma, molecular emission was observed, but no metallic detection was done. In this experiment, a lab-made electrothermal vaporizer (ETV) with tantalum coil was connected to the microchip plasma for aqueous sample introduction to detect metal ions. The electrode geometry of this microchip plasma was redesigned for better stability and easy monitoring of emission. The plasma was operated at an rf power of 30-70 W using argon gas at 300 mL/min. Gas kinetic temperatures between 800-3200 K were obtained by measuring OH emission band. Limits of detection of about 20 ng/mL, 96.1 ng/mL, and 1.01 μ g/mL were obtained for alkali metals, Zn, and Pb, respectively, when 10 μ L samples in 0.1% nitric acid were injected into the ETV.

• Journal of Environmental Health Sciences
• /
• v.26 no.4
• /
• pp.75-81
• /
• 2000

A matrix modification was studied for the determination of trace manganese in several seaweeds by electrothermal atomic absorption spectrophotometry(ETAAS). The type and quantity of modifiers were investigated to realize the efficient modification. Palladium was chosen as a single modifier. By the addition of palladium(5$\mu\textrm{g}$/$m\ell$) to 2ng/$m\ell$ manganese solution, the temperatures were raised from 1,00$0^{\circ}C$ to 1,20$0^{\circ}C$ for the charring and from 2,10$0^{\circ}C$ to 2,20$0^{\circ}C$ for the atomization as well as the sensitivity and reproducibility were improved. With such optimum conditions, the trace amount of manganese in several seaweeds(laver, tangle and brown seaweed) could be determined by a calibration curve method, and good recoveries of more than 965 were also obtained in the samples in which a given amount of manganese was spiked. The detection limit of this method was about 0.048ng/$m\ell$.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.28 no.12
• /
• pp.1997-2003
• /
• 2004

This paper presents a new method and an associated device, capable of detecting protein presence and size from the shift of the mechanical stiffness changing points due to the presence and size of proteins in a nano-gap actuator. Compared to the conventional resonant detection method, the present nanomechanical stiffness detection method shows higher precision for protein detection. The present method also offers simple and inexpensive protein detection devices by removing labeling process and optical components. We design and fabricate the nanomechanical protein detector using an electrothermal actuator with a nano-gap. In the experimental study, we measure the stiffness changing points and their coordinate shift from the devices with and without target proteins. The fabricated device detects the protein presence and the protein size of 14.0$\pm$7.4nm based on the coordinate shift of stiffness changing points. We experimentally verify the protein presence and size detection capability of the nanomechanical protein detector for applications to high-precision biomolecule detection.

• Journal of international Conference on Electrical Machines and Systems
• /
• v.2 no.4
• /
• pp.441-446
• /
• 2013

A thermal model of power modules based on the physical dimension and thermal properties is proposed in this paper. The heat path in the power module is considered as a one-dimensional heat transfer in the model. The method of the parameters extraction for the model is given in the paper. With high speed and accuracy, the thermal model is suit for electrothermal simulation. The proposed model is verified by experimental results.