• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.7
• /
• pp.4871-4877
• /
• 2015

This article presents a circuit and a system for IEEE 1588 based clock synchronization to generate a very accurate frequency signal required in femtocell devices. A prototype board and the experimental environment to verify the functions and to evaluate the performance are explained to verify the feasibility of the proposed synchronization system. To make low-cost femtocells without constraints on the place of installation, it is very important to study on the practical implementation of synchronization system based on IEEE 1588. The experimental result shows that the synchronization errors between -16 ns and 9 ns are guaranteed over the network of femtocell devices with the proposed synchronization circuits, thus the synchronization criteria of the 3GPP HNB are met.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.2
• /
• pp.840-845
• /
• 2013

In this paper, the broadband frequency double down-converter based on LC filter technologies has been designed and implemented, and its performances are introduced. The Designed frequency double down-converter is consisted with a low-noise amplifier, mixer, IF amplifier, LC filter, DC-block capacitor and RF-bypass capacitor. Especially, instead of active devices of a typical converter, the suggested converter designed using passive devices to provide both low-power consumption and low-cost model. As results of the measurement, the implemented frequency double down-converter realizes the broadband performance with the bandwidth of 100MHz (13~113MHz) at the center frequency of 63MHz, and its gain is approximately 40dB.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.17 no.6
• /
• pp.66-71
• /
• 2003

Electronic equipments made from integrated circuits and small-sized semiconductors is protected by surge protective devices(SPDs) such as ZnO varistors, Zener diode and gas discharge tube from lightning overvoltages. However the clamping voltage of SPDs is greatly influenced by the method of installing the SPDs. In this paper, the protective effects of SPDs according to types of system groundings were experimentally investigated. The separate grounding is a particularly undesirable way to install SPDs. The effectiveness of the common grounding point for ZnO varistors is more pronounced than that for gas discharge tubes. The common grounding at the terminal of SPDs is recommended as a best method of installing SPDs.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.27 no.2
• /
• pp.213-220
• /
• 2017

Pyroshock produced by the pyrotechnic devices can induce failures in nearby electronic devices. To handle and mitigate pyroshock inducing problems, appropriate measurement of pyroshock is essential. In this study, pyroshock measurement technique is established using laser Dopper vibrometers (LDVs) and shock accelerometers. Pyroshock produced by the explosive bolts and the pyrotechnic initiators under various environments is measured. The characteristics of pyroshock including the effects of supporting structures, propagation form on thin plate, sensor (contact and non-contact) types are discussed.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.28 no.10
• /
• pp.9-15
• /
• 2014

Standby power, so called an electric vampire, is a power which is consumed by appliances and office equipments connected to power sources while the devices are not performing. Sensor luminaires consist of PIR(Pyroelectric Infrared Ray) sensor, illuminance sensor(CdS), and light source. The sensor luminaires are one of the devices that consume a huge amount of standby power; it stands by for an average sum of 23 hours a day and performs only when moving subjects are detected under it, which barely takes up an hour per day. The purpose of this study is to provide basic materials to the selection of standby power items and to enable to explore a way to decrease the standby power by measuring and analyzing the power consumption of sensor luminaires. According to the results, the average standby power of LED sensor luminaires is 1.1W which is significantly higher than other products, and decrease in the standby power consumption of SMPS is important through the measurement.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.36 no.3
• /
• pp.285-290
• /
• 2008

Pyrotechnic shock or pyroshock is characterized as a transient vibration phenomena which shows large acceleration and high frequency range up to 10kHz during the operation of separation devices where explosives are used. During the flight of a launch vehicle, pyro-shock is mainly generated at several events such as satellite separation, fairing separation and stage separation. In this paper, characteristics of pyroshock are introduced briefly, and PEEK washer shock absorber is applied for the reduction of pyroshock in the high frequency range. With some electronic devices, reduction characteristic of pyroshock using washer type shock absorber are studied. Random vibration tests are also performed for the verification of vibrational characteristics.

• Journal of the Korean Applied Science and Technology
• /
• v.17 no.3
• /
• pp.174-177
• /
• 2000

The effect of a-sexithiophene(${\alpha}-6T$) layers on the light emitting diode (LED) were studied. The ${\alpha}-6T$ was used for a buffer layer in electroluminescent (EL) devices. Enhanced carrier (hole) injection and improved emission efficiency were observed. Carrier injection characteristics were investigated as a function of ${\alpha}-6T$ later thickness. The efficiency of the electroluminescence was proportional to the thickness of ${\alpha}-6T$ layer. The highest efficiency was observed 600A of ${\alpha}-6T$ later, which was about 1.5 times higher than that of device without ${\alpha}-6T$ later. The device with a-6T showed an operation voltage lowered by 2V. The ${\alpha}-6T$ layer can substitute hole blocking layer, and control charge injection properties.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.21 no.8
• /
• pp.20-26
• /
• 2007

A high ignition voltage is required to turn on the metal halide discharge(MHD) lamp. The igniter with high frequency resonance circuit needs more devices, such as sidac, arc-gab, SCR(silicon control rectifier), DIAC and so of which increase the complexity and decrease the reliability of the ignitor. This paper analyzes and designs a simple LC resonance type igniter without any extra switch devices. Moreover, the igniter will not influence the steady-state operation of the lamp. Through the mathematical analysis, the computer simulation and experiment results of a prototype ballast for 1[kW] metal halide lamp(MHL) lamp, the proposed igniter was verified to be effective.

• Journal of Korea Multimedia Society
• /
• v.19 no.3
• /
• pp.612-619
• /
• 2016

Applying evolved IT technology to increase the satisfaction of the consumer is a typical feature of the rapidly transformed service industry. Smart devices have taken a place as the mainstream of major media, moreover, IT service strategies utilizing smart devices have been constantly developed. Location recognition method of users has been proposed as one of the significant features to the IT service industry. The long-term care home services can be one example of user location recognition methods that real time computerization of service record utilize an attached tag to home of pensioners with RFID reader or an NFC function of mobile when a home carer provides service. And, the Homecare Electronics Management System (HEMS) and the various location recognition methods will be discussed to improve effectiveness of services. In this paper, we propose a home applicable electronic management system which insurer, home care service facilities, home cares, pensioners and guardians which enables to simultaneously check service records based on the improved system by use of iBeacon.

• Progress in Superconductivity
• /
• v.6 no.1
• /
• pp.7-12
• /
• 2004

Due to the very fast switching speed of Josephson junctions, superconductive digital circuit has been a very good candidate fur future electronic devices. High-speed and Low-power microprocessor can be developed with Josephson junctions. As a part of an effort to develop superconductive microprocessor, we have designed an RSFQ 4-bit ALU (Arithmetic Logic Unit) in a pipelined structure. To make the circuit work faster, we used a forward clocking scheme. This required a careful design of timing between clock and data pulses in ALU. The RSFQ 1-bit block of ALU used in this work consisted of three DC current driven SFQ switches and a half-adder. We successfully tested the half adder cell at clock frequency up to 20 GHz. The switches were commutating output ports of the half adder to produce AND, OR, XOR, or ADD functions. For a high-speed test, we attached switches at the input ports to control the high-speed input data by low-frequency pattern generators. The output in this measurement was an eye-diagram. Using this setup, 1-bit block of ALU was successfully tested up to 40 GHz. An RSFQ 4-bit ALU was fabricated and tested. The circuit worked at 5 GHz. The circuit size of the 4-bit ALU was 3 mm ${\times}$ 1.5 mm, fitting in a 5 mm ${\times}$ 5 mm chip.