• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.2
• /
• pp.207-211
• /
• 2004

We have performed computer simulation to obtain a globa1 optimization of power consumption and viewing angle characteristic of reflective twisted nematic (R-TN) mode liquid crystal display (LCD) with sin81e polarizer and λ/4 plate. Our studies shout that with increasing the twist angle, a steepness of reflectance-voltage curve increase, operation voltages decreases, the region where contrast ratio (CR) greater than 10 increases but the reflectance of the white state starts to decrease at above the twist angle of 75$^{\circ}$. Above the twist angle of 90$^{\circ}$, the R-TN mode LCD shows the most favorable combination of low consumption and good viewing angle characteristic.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.11 no.8
• /
• pp.3823-3840
• /
• 2017

This paper analyzes the nodes deployment optimization problem in energy constrained wireless sensor networks, which multi-hop cooperative beamforming (CB) based cooperative-multi-input-single-output (CMISO) transmission is adopted to reduce the energy consumption. Firstly, we establish the energy consumption models for multi-hop SISO, multi-hop DSTBC based CMISO, multi-hop CB based CMISO transmissions under random nodes deployment. Then, we minimize the energy consumption by searching the optimal nodes deployment for the three transmissions. Furthermore, numerical results present the optimal nodes deployment parameters for the three transmissions. Energy consumption of the three transmissions are compared under optimal nodes deployment, which shows that CB based CMISO transmission consumes less energy than SISO and DSTBC based CMISO transmissions. Meanwhile, under optimal nodes deployment, the superiorities of CB based CMISO transmission over SISO and DSTBC based CMISO transmissions can be more obvious when path-loss-factor becomes low.

• Journal of Sensor Science and Technology
• /
• v.27 no.1
• /
• pp.21-24
• /
• 2018

A temperature sensor with a binary output was implemented using switched-capacitor circuits in a $0.35-{\mu}m$ CMOS(com-plementary metal-oxide semiconductor) process. The measured temperature exhibited good agreement with the oven temperature after calibration. The measured power consumption was 5.61 mW, slightly lower than the simulated power consumption of 6.63 mW.

• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.1335-1336
• /
• 2007

Among the emerging non-volatile memory technologies, phase change memories are the most attractive in terms of both performance and scalability perspectives. Phase-change random access memory(PRAM), compare with flash memory technologies, has advantages of high density, low cost, low consumption energy and fast response speed. However, PRAM device has disadvantages of set operation speed and reset operation power consumption. In this paper, we investigated scalability of $Ge_{1}Se_{1}Te_{2}$ chalcogenide material to improve its properties. As a result, reduction of phase change region have improved electrical properties of PRAM device.

• IEIE Transactions on Smart Processing and Computing
• /
• v.1 no.2
• /
• pp.117-124
• /
• 2012

A client collaboration (CC) system is proposed for a user relay system. The proposed scheme focuses on the management of transmit power and leakage interference. In the proposed CC system, edge users transmit signals to the masters considered as user relays. The masters relay the signals of the edge users to the base station using the resource blocks (RBs) that are assigned to the edge users. The leakage interference and power consumption were analyzed in the CC system. In addition, an optimal master location problem was formulated based on the signal-to-leakage-plus-noise ratio (SLNR). Because the optimal master location problem is quite complex, a sub-optimal master location problem was proposed and a closed-form sub-optimal master location was obtained. The edge users generate smaller leakage interference and power consumption in the proposed CC system compared to the system without the CC. The numerical results showed that the edge users generate smaller leakage interference and power consumption in the proposed CC system compared to the system without the CC, and the average throughput increases.

• Proceedings of the IEEK Conference
• /
• 2008.06a
• /
• pp.545-546
• /
• 2008

This paper presents a low power CMOS low noise amplifier for UWB applications. To reduce the power consumption, two cascode amplifiers was stacked in DC. Designed with $0.18-{\mu}m$ CMOS technology, the proposed LNA achieves 20dB flat gain, below 3dB noise figure, and the power consumption of 5.2mW from a 1.8 V supply voltage.

• ETRI Journal
• /
• v.37 no.1
• /
• pp.118-127
• /
• 2015

The power consumption of 3D many-core processors can be reduced, and the power delivery of such processors can be improved by introducing voltage island (VI) design using on-chip voltage regulators. With the dramatic growth in the number of cores that are integrated in a processor, however, it is infeasible to adopt per-core VI design. We propose a 3D many-core processor architecture that consists of multiple voltage clusters, where each has a set of cores that share an on-chip voltage regulator. Based on the architecture, the steady state temperature is analyzed so that the thermal characteristic of each voltage cluster is known. In the voltage scaling and task scheduling stages, the thermal characteristics and communication between cores is considered. The consideration of the thermal characteristics enables the proposed VI formation to reduce the total energy consumption, peak temperature, and temperature gradients in 3D many-core processors.

• Transactions on Electrical and Electronic Materials
• /
• v.6 no.4
• /
• pp.173-176
• /
• 2005

A new $MoO_3$ based microsensor with low power consumption was presented. Typical size of sensor was 5mm in width and 8mm in length. As a sensitive electrode, $MoO_3$ was successfully fabricated by IC technology on pyrex glass of $250{\mu}m$ in thickness. After annealing at $550^{\circ}C$ for 3hrs, the film was fully crystallized and demonstrated as pure $MoO_3$ structure. The grain size of $MoO_3$ was plat like and typical size was about $1{\mu}m$. Based on the results of sensitivity measurement, $MoO_3$ microsensor shows especially high selectivity to $H_2$ reducing gas atmosphere. The applied heater power was lower than 0.5 Watt.

• Proceedings of the IEEK Conference
• /
• 2000.07a
• /
• pp.351-354
• /
• 2000

In the past, we proposed an IDDQ testable design method for static CMOS PLA circuits. All bridging faults can be detected in NOR planes of our testable designed PLA circuits by IDDQ testing with 4 kinds of test input vectors which are independent of the logical functions to be realized. However, the testable designed PLA circuits consume large power in the normal operation. In this paper, a new IDDQ testable design method is proposed and evaluated by some experiments. The experimental results show that the PLA circuit designed with our method can work with low power consumption than the previous one.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.29 no.11
• /
• pp.605-611
• /
• 2017

The purpose of this study is to calculate the energy consumption rate based on data regarding energy use in office buildings, and to confirm the general characteristics of energy consumption. The energy consumption rate of the building is calculated by dividing the energy consumption by the floor area. The energy consumption rate of small-sized office buildings was calculated as $101.48{\sim}201.55kWh/m^2{\cdot}year$ and in the case of medium-sized buildings, the range was $92.77{\sim}177.89kWh/m^2{\cdot}year$. In the case of small buildings, it was found that the energy consumption was $73.24kWh/m^2{\cdot}year$ in electronic device, $34.31kWh/m^2{\cdot}year$ in hot water supply, and $18.37kWh/m^2{\cdot}year$ in heating. In the case of medium-sized buildings, electronic devices was $73.08kWh/m^2{\cdot}year$, lighting was $18.35kWh/m^2{\cdot}year$ and heating, $15.37kWh/m^2{\cdot}year$. In all of the study buildings, the peak heating energy use was observed from 8:00 a.m. to 10:00 a.m during the winter, and the peak power management was required. Energy use at and around the midnight hour is confirmed to be 40~60% of weekly working hours, so it is necessary to manage power use at night time as well as during the day. In order to improve the accuracy of future studies, it is necessary to make efforts to secure the data with standardized energy measuring units for the various type of buildings.