• 한국전기전자재료학회논문지
• /
• 제20권9호
• /
• pp.802-807
• /
• 2007

We have developed red phosphorescent top emission organic light-emitting diodes with transparent metal cathodes deposited by using thermal evaporation technique. Phosphorescent guest molecule, BtpIr(acac), was doped in host CBP for the red phosphorescent emission, Ca/Ag, Ba/Ag, and Mg/Ag double layers were used as cathode materials of top emission devices, which were composed of glass/Ni/2TNATA(15 nm)/${\alpha}$-NPD(35 nm)/CBP:BtpIr(acac)(40 nm, 10%)/BCP(5 nm)/$Alq_3$(5 nm)/cathodes. The optical transparencies of these metal cathodes strongly depend on underlying Ca, Ba, and Mg layers. These layers also strongly affect the electrical conduction and emission properties of the red phosphorescent top emission devices.

• 한국전기전자재료학회논문지
• /
• 제30권1호
• /
• pp.59-62
• /
• 2017

CNT (carbon nanotube) resistors with low resistance and negative TCR (temperature coefficient of resistance) were fabricated with yarned CNT (carbon nanotube) fibers. The CNT fibers were prepared by yarning CNTs grown on the silicone substrate by CVD (chemical vapor deposition) method. The CNT resistors were fabricated by winding CNT fibers on the surface of ceramic rod. Both metal terminals were connected with the CNT fiber wound on the ceramic rod. We measured electrical resistance and thermal stability with the number of CNT fibers wound. The CNT resistor system shows linearly decreased resistance with the number of CNTs wound on the ceramic rod and saturated at 20 strands. The CNT resistor system has negative TCR between $-1,000{\sim}-2,000ppm/^{\circ}C$ and stable frequency properties under 100 kHz.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 추계학술대회 논문집 Vol.14 No.1
• /
• pp.112-116
• /
• 2001

Organic Electroluminescence device, which have the single-layer structure of ITO(indium-tin-oxide)/MEH-PPV (Poly[2-(2'-ethylhexyloxy )-5-methoxy-1,4-pheny lenevinylene])/Al(aluminium) and ITO/MEH-PPV/$Alq_3$(tris-8-hydroxyquinolinato aluminium)/Al were fabricated and electrical properties were investigated. Experimental results, in single-layer structure, shown that turn on voltage is about 12 V, and current density increases as a function of increasing temperature. It was explained by thermionic emission. In double-layer structure, thickness $200\AA$ of $Alq_3$ is shown electrical properties that turn on voltage is about 11 V, and current density decreases as a function of increasing temperature.ࠀȀ 耀Ѐ€

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1999년도 추계학술대회 논문집
• /
• pp.354-357
• /
• 1999

This paper describes on the electrical and physical charateristics thin-film type Pt-RTD\\`s on Si wafers, in which MgO thin-films were used as medium layer in order to improve adhesion of Pt thin-films to SiO$_2$ layer. The MgO medium layer had the properties of improving Pt adhesion to SiO$_2$ and insulation without chemical reaction to Pt thin-films and the resistivity of Pt thin-films was improved. In the analysis of properties of Pt-RTD, TCR value had 3927 ppm/$^{\circ}C$ and liner in the temperature range of room temperature to 40$0^{\circ}C$

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 추계학술대회 논문집
• /
• pp.112-116
• /
• 2001

Organic Electroluminescence device, which have the single-layer structure of ITO(indium-tin-oxide)/MEH-PPV (Poly [2-(2'-ethylhexyloxy)-5-methoxy-1, 4-phenylenevinylene])/Al(aluminium) and ITO/MEH-PPV/Alq$_3$(tris-8-hydroxyquinolinato aluminium)/Al were fabricated and electrical properties were investigated. Experimental results, in single-layer structure, shown that alum on voltage is about 12 V, and current density increases as a function of increasing temperature. It was explained by thermionic emission. In double-layer structure, thickness 200 $\AA$ of Alq$_3$ is shown electrical properties that turn on voltage is about 11V, and current density decreases as a function of increasing temperature.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 춘계학술대회 논문집 센서 박막재료 반도체 세라믹
• /
• pp.95-98
• /
• 2003

Tin doped indium oxide(ITO) films, which is widely used as a transparent conductor in optoelectronic devices such as solar cell, liquid crystal display, plasma display panel, thermal heater, and other sensors, were prepared by using the capacitively coupled DC magnetron sputtering method. The influence of the substrate temperature, working gas pressure and deposition time on the electrical, optical and morphological properties were investigated experimentally. ITO films with the optimum growth conditions showed resistivity of $2.36{\times}10^{-4}(\Omega}-cm$ and transmittance of 86.28% for a film 680nm thick in the wavelength range of the visible spectrum.

• 대한금속재료학회지
• /
• 제56권12호
• /
• pp.915-920
• /
• 2018

With the development of modern microelectronics technologies, the power density of electronic devices is rapidly increasing, due to the miniaturization or integration of device elements which operate at high frequency, high power conditions. Resulting thermal problems are known to cause power leakage, device failure and deteriorated performance. To relieve heat accumulation at the interface between chips and heat sinks, thermal interface materials (TIMs) must provide efficient heat transport in the through-plane direction. We report on the enhanced thermal conduction of $Al_2O_3-based$ polymer composites, fabricated by the surface wetting and texturing of thermally conductive hexagonal boron nitride(h-BN) nanoplatelets with large anisotropy in morphology and physical properties. The thermally conductive polymer composites were prepared with hybrid fillers of $Al_2O_3$ macro beads and surface modified h-BN nanoplatelets. Hexagonal boron nitride (h-BN) has high thermal conductivity and is one of the most suitable materials for thermally conductive polymer composites, which protect electronic devices by efficient heat dissipation. In this study, we synthesized hexagonal boron nitride nanoparticles by the pyrolysis of cost effective precursors, boric acid and melamine. Through pyrolysis at $900^{\circ}C$ and subsequent annealing at $1500^{\circ}C$, hexagonal boron nitride nanoparticles with diameters of ca. 50nm were synthesized. We demonstrate that the addition of a small amount of calcium fluoride ($CaF_2$) during the preparation of the melamine borate adduct significantly enhanced the crystallinity of the h-BN and assisted the growth of nanoplatelets up to 100nm in diameters. The addition of a small amount of h-BN enhanced the thermal conductivity of the $Al_2O_3-based$ polymer composites, from 1.45W/mK to 2.33 W/mK.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1998년도 추계학술대회 논문집
• /
• pp.121-124
• /
• 1998

The purpose of this study is to research and develop solid polymer electrolyte(SPE) for Li secondary battery. This paper describes temperature dependence of conductivity, impedance spectroscopy, electrochemical properties of PVDF electrolytes as a function of a mixed ratio. Polyvinylidene(PVDF) based polymer electrolyte films were prepared by thermal gellification method of preweighed PVDF, plasticizer and Li salt. The conductivity of PVDF electrolytes was 10$\^$-3/S/cm. 25PVDFPC$\_$10/EC$\_$10/LiClO$_4$ electrolyte shows the better conductivity of the others. 25PVDFPC$\_$10/EC$\_$10/LiClO$_4$electrolyte remains stable up to 4.7V vs. Li/Li$\^$+/. Steady state current method and ac impedance used for the determination of transference numbers in PVDFD electrolyte film. The transference number of 25PVDFPC$\_$10/EC$\_$10/LiClO$_4$electrolyte is 0.58.

• 한국전기전자재료학회논문지
• /
• 제27권3호
• /
• pp.184-188
• /
• 2014

The electro-optic properties in Langmuir Blodgett films of poly (vinylidene fluoride trifluoroethylene) are investigated in the crossover region between two and three dimensions. The absence of finite size effect is observed in the films thinner than 20 nm, which confirms that these films are two dimensional ferroelectrics. The copolymer LB film of P(VDF-TrFE) exhibits the largest electro-optic response(26 pm/V) at 10 layer thickness. The cross-over behavior of electro-optic effect around the 10 layer thickness was discussed with the formation of nanomesa after thermal annealing.

• 한국전기전자재료학회논문지
• /
• 제21권2호
• /
• pp.188-193
• /
• 2008

Epoxy/Organically Modified Layered Silicate Nanocomposites were prepared by dispersing synthetic layered silicate modified with alkyl ammonium ions. In the dispersing process, the organically modified layered silicate were mixed in epoxy resin with shearing, and aggregation of the silicate were removed by centrifugal separation after mixing epoxy resin and silicates. Micrographs taken by transmission electron microscopy(TEM) indicate that the nanocomposites have a mixed morphology including both parallel silicate layers and exfoliated silicate layers area, As the thermal properties, the glass transition temperature of the nanocomposites was shifted to a higher temperature($+6^{\circ}C$)than pure epoxy. Furthermore, dispersion of OMLS will prevented relative permittivity from increasing at a high temperature above the glass transition temperature.