• Korean Journal of Materials Research
• /
• v.27 no.11
• /
• pp.617-623
• /
• 2017

Mesoporous carbon nanofibers as electrode material for electrical double-layer capacitors(EDLCs) are fabricated using the electrospinning method and carbonization. Their morphologies, structures, chemical bonding states, porous structure, and electrochemical performance are investigated. The optimized mesoporous carbon nanofiber has a high sepecific surface area of $667m^2\;g^{-1}$, high average pore size of 6.3 nm, and high mesopore volume fraction of 80 %, as well as a unifom network structure consiting of a 1-D nanofiber stucture. The optimized mesoporous carbon nanofiber shows outstanding electrochemical performance with high specific capacitance of $87F\;g^{-1}$ at a current density of $0.1A\;g^{-1}$, high-rate performance ($72F\;g^{-1}$ at a current density of $20.0A\;g^{-1}$), and good cycling stability ($92F\;g^{-1}$ after 100 cycles). The improvement of the electrochemical performance via the combined effects of high specific surface area are due to the high mesopore volume fraction of the carbon nanofibers.

• Journal of the Korean Chemical Society
• /
• v.40 no.1
• /
• pp.37-43
• /
• 1996

The electrochemical impedance spectra of polyaniline film coated on tungsten electrodes by cyclic voltammetry have been measured in 0.1 M aqueous sulfuric acid solution. An electrochemical cell composed of large redox capacitance and low resistance of PANI-film in series was in agreement with the conductive behavior reported at these potentials. When the PANI was coated on bare tungsten, the electrolytic resistance was only observed. However, on the oxidized tungsten instead of bare tungsten, the resistance of tungsten oxide and the contact resistance between PANI and tungsten oxide were additionally observed. Equivalent electrical circuits have been deduced from the impedance data. It was therfore possible to obtain the parameters of the ionic mass transport within the film.

• Journal of the Korean Electrochemical Society
• /
• v.15 no.3
• /
• pp.160-164
• /
• 2012

The lead-acid batteries are the most often used in human life, because of their low cost, good reversibility and high potential but they have limit cycle ability with low capacitance. The main causes of this problem are forming recrystallization of $PbSO_4$ on electrodes surface during cycles which the recrystallization of $PbSO_4$ is known as sulfation. In this study, formation process of sulfation was investigated depending on charge and discharge cycle numbers. And we decomposed sulfation to renew cycle ability of lead-acid batteries. The renewed lead-acid batteries recovered to 84% compared to first capacity after 600 cycles.

• Journal of Electrochemical Science and Technology
• /
• v.3 no.2
• /
• pp.80-84
• /
• 2012

The polyaniline (PANI) electrodes are prepared by chemical synthesis and electrodeposition methods and their supercapacitive properties are characterized and compared by morphology observation, cyclic voltammetry as a function of scan rate, and impedance spectra analysis. In particular, the supercapacitive properties obtained in the range of higher potential scan rates (e.g., over $200mV\;s^{-1}$) are emphasized to be capable of utilizing adequately the high power capability of supercapacitor. As a result, the PANI electrode by the electrodeposition shows superior specific capacitance (max. $474F\;g^{-1}$ at $10mV\;s^{-1}$ and about $390F\;g^{-1}$ at $500mV\;s^{-1}$) than those by the chemical synthesis method. This is mainly due to highly porous structure obtained by the electrodeposition to yield higher specific surface area.

• Journal of Electrochemical Science and Technology
• /
• v.9 no.2
• /
• pp.93-98
• /
• 2018

$MnO_2$, a metal oxide used as an electrode material in electrochemical capacitors (EDLCs), has been applied in binary oxide and conducting polymer hybrid electrodes to increase their stability and capacitance. We developed a method for electrodepositing Mn-Ni oxide/PANI, Mn-Ni oxide/PEDOT, and Mn-Ni-Ru oxide/PEDOT films on carbon paper in a single step using a mixed bath. Mn-Ni oxide/PEDOT and Mn-Ni-Ru oxide/PEDOT electrodes used in an electro-osmotic pump (EOP) have shown better efficiency compared to Mn-Ni oxide and Mn-Ni oxide/PANI electrodes through testing in water as a pumping solution. EOP using a Mn-Ni-Ru oxide/PEDOT electrode was also tested in a 0.5 mM $Li_2SO_4$ solution as a pumping solution to confirm the effect of the $Li^+$ insertion/de-insertion reaction of Ruthenium oxide on the EOP. Experimental results show that the flow rate increases with the increase in current in a 0.5 mM $Li_2SO_4$ solution compared to that obtained when water was used as a pumping solution.

• Particle and aerosol research
• /
• v.15 no.4
• /
• pp.183-190
• /
• 2019

Here, we introduce porous graphene balls (PGB) showing superior electrochemical properties as supercapacitor electrode materials. PGB was fabricated via activation of graphene oxides (GO) by H₂O₂ and aerosol spray drying in series. Effect of activation on the morphology, specific surface area, pore volume, and electrochemical properties were investigated. As-prepared PGB showed spherical morphology containing pores, which lead to the effective prevention of restacking in graphene sheets. It also exhibited a large surface area, unique porous structures, and high electrical conductivity. The electrochemical properties of the PGB as electrode materials of supercapacitor are investigated by using aqueous KOH under symmetric two-electrode system. The highest specific capacitance of PGB was 279 F/g at 0.1 A/g. In addition, the high rate capability (93.8% retention) and long-term cycling stability (92.2%) of the PGB were found due to the facilitated ion mobility between the porous graphene layers.

• Analytical Science and Technology
• /
• v.23 no.5
• /
• pp.505-510
• /
• 2010

When polybutadiene dissolved in toluene was a binder of carbon powder, the volatility of solvent just after electrode fabrication assured the mechanical solidity of the carbon paste electrode. This characteristic met the qualifications for practical use of carbon paste electrodes. A new enzyme electrode bound with butadiene rubber was constructed. In order to confirm whether it shows quantitative electrochemical behaviors or not, its electrochemical kinetic parameters, e.g. the symmetry factor, the exchange current density, the capacitance of double layer, the time constant, the maximum current, the Michaelis constant and other factors were investigated. These experimental facts showed that butadiene rubber is a recommendable binder for practical use of a carbon paste electrode.

• Journal of the Korean Chemical Society
• /
• v.40 no.5
• /
• pp.308-316
• /
• 1996

The electrochemical behavior of glassy carbon and PVDF synthesis graphite materials with compact surface have been characterized by impedance spectroscopy. The Faraday-impedance both carbon materials were depended highly on polarization and the difference of electrochemical behavior accord to structure of surface between glassy carbon and synthesis graphite was represented, in these evaluated equivalent circuits, PVDF synthesis graphite was indicated with form that is added resistance and capacitance by the hydrophobic binder to glassy carbon equivalent circuit.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.14 no.3
• /
• pp.188-196
• /
• 2009

Due to its high power density, long cycle life and clean nature supercapacitors are widely used for improving the dynamic characteristics of the new and renewable energy sources and extending the battery run-time and life. In this paper improved dynamic model of the supercapacitor is developed by the electrochemical impedance spectroscopy technique. The developed model can be used to accurately estimate the dynamic behaviour of the supercapacitor and calculate the exact capacitance value at a certain state of charges. The model of the supercapacitor in the frequency domain is equivalently transformed into that in the time domain for Matlab/Simulink simulaton. The simulation data shows fine agreements with experimental results, thereby proving the validity and the accuracy of the developed model.

• Bulletin of the Korean Chemical Society
• /
• v.34 no.8
• /
• pp.2343-2347
• /
• 2013

In this work, manganese dioxide ($Mn_3O_4$)/carbon black (CB) composites (Mn-CBs) were prepared by an in situ coating method as electrical fillers and the effect of the Mn-CBs on the electrical performance of activated carbon (AC)-based electrodes was investigated. Structural features of Mn-CBs produced via in situ coating using a $KMnO_4$ solution were confirmed by XRD and TEM images. The electrical performances, including cv curves, charge-discharge behaviors, and specific capacitance of the ACs/Mn-CBs, were determined by cyclic voltammograms. It was found that the composites of $Mn_3O_4$ and CBs were successfully formed by in situ coating method. ACs/Mn-CBs showed higher electrical performance than that of AC electrodes fabricated with conventional CBs due to the pesudocapacitance reaction of manganese oxides in the aqueous electrolyte. Consequently, it is anticipated that the incorporation of $Mn_3O_4$ into CBs could facilitate the utilization of CBs as electrical filler, leading to enhanced electrochemical performance of AC electrodes for supercapacitors.