• 한국세라믹학회지
• /
• 제36권4호
• /
• pp.451-458
• /
• 1999

TiC-Mo2C composites were prepared from Ti-C-Mo system by HPCS which has a great advantage of simulataneous synthesis and sintering In this study physical properties and microstructures of the com-posites were measured and observed to compare the sintering effects of Ni and Co each other : The results showed that the role of 5 wt% Ni in the sintering of the carbide composites was superior to that of 5wt% Co and the optimum content of Mo in the Ti-C-Mo system was 20wt% The carbide composites prepared under these two conditions had the best properties with 1.0% in apparent porosity 97.6% in relative density 19.1GPa in Vickers hardness and 5.3MPa$.$m1/2 in fracture toughness.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 추계학술대회 논문집 Vol.15
• /
• pp.300-304
• /
• 2002

We fabricated thick film monopole antennas using Mo-doped $BiNbO_{4}$ ceramics and investigated their electrical properties as a function of the Mo-doping concentration. Compared with undoped $BiNbO_{4}$ ceramics, 10 at.% Mo-doping improved microwave dielectric properties of ceramics by increased sintered density as well as decreased space charge density. Further increase in the Mo-doping concentration caused formation of $Bi_{2}MoO_{6}$ phases, resulting in deterioration of the microwave characteristics. The gain and bandwidth of the ceramic monopole antenna were also greatly affected by the Mo-doping concentration. When Mo-doping concentration was 10 at%, highest gain of ~0.7dBi with lowest bandwidth of 30% at 2.3GHz was obtained.

• 열처리공학회지
• /
• 제4권3호
• /
• pp.7-12
• /
• 1991

Effects of Mo content and aging conditions on the amount of retained austenite and mechanical properties of 18 Ni maraging steels were investigated. Maraging steels were fabricated with variation of Mo content. 3, 5, 7, 9% and heat treated by austenitizing at $840^{\circ}C$ for 1 hour and then aged at $480^{\circ}C$ for 0.5~100 hours. It was found that the amount of retained austenite after aolution treatment was negligible up to 5% Mo. 8 and 11 volume percents of retained austenite were obtained with 7 and 9% Mo respectively. The maximum hardness and yield strength without great loss of impact toughness were attained in the range of 4~8 hours of aging time at $480^{\circ}C$ with 5% Mo. It was concluded, as a result, that the optimum Mo content for the good combination of strength and toughness is to be 5% Mo.

• 한국주조공학회지
• /
• 제33권1호
• /
• pp.1-7
• /
• 2013

The effect of the Mo addition on the high temperature creep properties of the 9Cr-3W steel was also evaluated. Two experimental steels, (9Cr-3W and 9Cr-3W-0.5Mo), were prepared using a vacuum induction melting process, followed by hot rolling and heat treatment processes. Three types of precipitates, ($M_{23}C_6$, Nb-rich MX and V-rich MX) were observed in a typical tempered martensitic matrix. Significant effects of the Mo addition on the tensile properties were not observed. However, the creep properties at $650^{\circ}C$ under applied stresses of 140 and 150 MPa were considerably enhanced by the Mo addition. The microstructural observation after the creep test indicated that the addition of Mo could function to retain the recovery of the martensitic matrix, thus resulting in the enhanced creep properties of the 9Cr-3W-0.5Mo steel. Furthermore coarsening of the $M_{23}C_6$ carbides and formation of Laves phases were observed in both samples after the creep tests.

• 한국주조공학회지
• /
• 제29권6호
• /
• pp.257-264
• /
• 2009

The effects of silicon and molybdenum on the temperature-dependent properties of high silicon and high molybdenum ductile cast iron were investigated. Microstructure was composed of ferrite, cell boundary complex carbide, carbide precipitated in the grain and graphite. The number and size of carbide decreased with the increase of silicon content and increased with the increase of molybdenum content, however, the size of cell boundary carbide increased above 0.81wt%Mo. The room temperature tensile strength increased with the increase of silicon and molybdenum contents. That did not increase with the latter with more than 0.8wt%. Meanwhile the high temperature tensile strength showed the similar trend to that of room temperature one, that of the specimen with 0.55wt%Mo was the highest. The $A_1$ transformation temperature increased with the silicon and molybdenum contents, and showed similar tendency with the variation of strength. It was discussed due to the solubility limit of Molybdenum in ferrite, of which value was assumed to be in the vicinity of 0.81wt%Mo. The weight after oxidation at 1,173K showed the result caused by the difference in solubility of molybdenum in the matrix. That and the thickness change after oxidation did not show any consistent trend with the silicon and molybdenum contents.

• 소성∙가공
• /
• 제24권1호
• /
• pp.44-51
• /
• 2015

The current study seeks to examine the effects of V and C additions on the mechanical and low thermal expansion properties of a high strength invar base alloy. The base alloy (Fe-36%Ni-0.9%Co-2.75%Mo-0.7Cr-0.23Mn-0.17Si-0.3%C, wt.%) contains $Mo_2C$ carbides, which form as the main precipitate. In contrast, alloys with additions of 0.4%V+0.3%C (alloy A) or 0.4%V+0.45%C (alloy B) contain $Mo_2C$+[V, Mo]C carbides. The average thermal expansion coefficients of these high strength invar based alloys were measured in the range of $5.16{\sim}5.43{\mu}m/m{\cdot}^{\circ}C$ for temperatures of $15{\sim}230^{\circ}C$. Moreover, alloy B showed lower thermal expansion coefficient than the other alloys in this temperature range. For the mechanical properties, the [V, Mo]C improved hardness and strengths(Y.S. and T.S.) of the high strength invar base alloy. T.S.(tensile strength) and Y.S.(yield strength) of hot forged alloy B specimen were measured at 844.6MPa and 518.0MPa, respectively. The tensile fractography of alloy B exhibited a ductile transgranular fracture mode and voids were initiated between the [V, Mo]C particles and the matrix. Superior properties of high strength and low thermal expansion coefficient can be obtained by [V, Mo]C precipitation in alloy B with the addition of 0.4%V and 0.45%C.

• 공업화학
• /
• 제3권1호
• /
• pp.53-63
• /
• 1992

프로필렌을 선택산화시켜 아크로레인을 제조하는 반응을 Bi-molybdate 촉매상에서 고정층 반응기를 사용하여 연구하였다. ${\alpha}-Bi_2Mo_3O_{12}$위에 $MoO_3$를 담지시킨 M/BM-series 촉매는 함침법으로 제조되었고, 역으로 BM/M-series 촉매는 $MoO_3$위에 ${\alpha}-Bi_2Mo_3O_{12}$을 침전시켜 제조하였다. 또한 촉매의 특성분석을 위하여 질소흡착과 XRD, SEM을 이용하였다. M/BM-series 촉매에서는 $MoO_3$가 작은 입자로 분산되고 ${\alpha}-Bi_2Mo_3O_{12}$의 결정구조는 $MoO_3$상이 추가되어도 그 형상이 변하지 않는 채로 유지되었으나, BM/M-series 촉매의 표면형상 및 전체 구조는 촉매제조 중에 생기는 침전물인 $Bi(OH)_3$가 소성 도중 $MoO_3$와 반응하여 ${\alpha}-Bi_2Mo_3O_{12}$을 형성하는 관계로 그 조성에 따라 매우 불규칙적으로 변화하였다. 반응실험 결과, 두 종류의 촉매 모두에서 excess $MoO_3$가 포함되었을 때 활성이 크게 증가하였는데, 이는 선별산화반응이 주로 ${\alpha}-Bi_2Mo_3O_{12}$에서 일어나고 $MoO_3$는 ${\alpha}-Bi_2Mo_3O_{12}$에 산소 공급을 원활히 하여 활성을 증가시키기 때문으로 판명되었다. 또한 이러한 활성 증가는 ${\alpha}-Bi_2Mo_3O_{12}$와 기계적 혼합물 (mechanical mixture)에서도 관찰되었다.

• Asian-Australasian Journal of Animal Sciences
• /
• 제24권8호
• /
• pp.1031-1040
• /
• 2011

The objective of this study was to characterize factors influencing genetic improvement of dairy cattle for milk production at farm level. Data were accumulated from 305-day milk yields and pedigree information from 1,921 first-lactation dairy cows that calved from 1990 to 2007 on 161 farms in Central Thailand. Variance components were estimated using average information restricted maximum likelihood procedures. Animal breeding values were predicted by an animal model that contained herd-year-season, calving age, and regression additive genetic group as fixed effects, and cow and residual as random effects. Estimated breeding values from cows that calved in a particular month were used to estimate genetic trends for each individual farm. Within-farm genetic trends (b, regression coefficient of farm milk production per month) were used to classify farms into 3 groups: i) farms with negative genetic trend (b<-0.5 kg/mo), ii) farms with no genetic trend (-0.5 kg/$mo{\leq}b{\leq}0.5$ kg/mo), and iii) farms with positive genetic trend (b>0.5 kg/mo). Questionnaires were used to gather information from individual farmers on educational background, herd characteristics, farm management, decision making practices, and opinion on dairy farming. Farmer's responses to the questionnaire were used to test the association between these factors and farm groups using Fisher's exact test. Estimated genetic trend for the complete population was $0.29{\pm}1.02$ kg/year for cows. At farm level, most farms (40%) had positive genetic trend ($0.63{\pm}4.67$ to $230.79{\pm}166.63$ kg/mo) followed by farms with negative genetic trend (35%; $-173.68{\pm}39.63$ to $-0.62{\pm}2.57$ kg/mo) and those with no genetic trend (25%; $-0.52{\pm}3.52$ to $0.55{\pm}2.68$ kg/mo). Except for educational background (p<0.05), all other factors were not significantly associated with farm group.

• 한국분말재료학회지
• /
• 제6권1호
• /
• pp.62-68
• /
• 1999

The effects of the carbon content ranging from 17.5 to 21.0 wt.% in TiC-30vol.% $Ni_3Al$ cenmet and the $Mo_2C$ content raging from 0 to 30 wt.% in TiC-20 vol.% $Ni_3Al$ cermet were investigated in the relation to the microstures and harbness. The speciment were sintered at 140$0^{\circ}C$, 143$0^{\circ}C$ and 145$0^{\circ}C$ for 60minutes. The results were summarized as follows; 1) The shrinkages and relative densitites of the specimens were incrased up to 20.0 wt.% C and then decreased. 2) The grains of TiC were almost the same size with the different content of carbon. Free carbons were appeared on the microstrures when carbon was added over 20.5 wt.% while TiC and $Ni_3Al$l were formed when carbon was added below 20.0 wt.%; 3) The lattice parameters of the $Ni_3Al$ and TiC phases were increased up to 20.5 wt.% C, and then saturated. 4) The hardess was increased up to 20.0 wt.% C, and then decreased. 5) The $Mo_2C$ made the TiC grains fine and the surrounding structure around TiC gains. 6) The micropores were decreased with increasing the binder and the sintering temperature. 7) The lattice parameter of the $Ni_3Al$l ana TiC were almost the samp up to 10 wt.% $Mo_2C$ and then decreased. 8) The hatdness was increased up to 5wt.% $Mo_2C$ and then decreased owing to the micrpores. 9) The more the binder phase, the higher the relative density and the proper $Mo_2C$ amount of $TiC-Ni_3Al$ cermets were obtained.

• 한국표면공학회지
• /
• 제52권4호
• /
• pp.227-232
• /
• 2019

Mo-N based coatings have been studied for enhancing mechanical characteristics of thin films. In the case of Mo-X-N coatings, the microstructure and mechanical properties can be affected by the addition of the third element. In this work, Mo-Cu-N coatings were successfully fabricated with varying the Cu content from 4.5 at% to 31 at% by the co-sputtering method. Thus, properties of the coatings were analyzed by EDS, SEM, XRD, AFM, nano indentation and scratch test techniques. From observed results, MoxN bonds were made in a nitrogen atmosphere and Cu elements were present at grain boundaries. In addition, coatings with the Cu content above 14 at% had a Cu3N peak in the XRD results. Thus, it is suggested that the formation of Cu3N phase affected the microstructure and mechanical properties of Mo-Cu-N coatings. Mechanical properties of Mo-Cu-N coatings were found to be relatively better at Cu content of about 12 at%.