• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2001년도 토목섬유기술위원회 학술세미나 논문집
• /
• pp.13-19
• /
• 2001

The use of reinforced soil have been increased due to it's cost effectiveness, flexibility and so on. In this study, a full-scale reinforced soil with rigid facing were constructed to investigate the soil pressure variation of reinforcing system. The results of soil pressure during backfill construction are described. The influence of facing stiffness on soil pressure is addressed. The results show that lateral earth pressures on the wall are active state during backfill. It is obtained that the lateral soil pressure highly depends on the installation condition of pressure cell and construction condition. Long-term measurement will be followed to verify the design assumptions with respect to the distribution of lateral stress on the facing.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2000년도 봄 학술발표회 논문집
• /
• pp.435-440
• /
• 2000

It is important to pay careful attention to construction backfill for the structural integrity of concrete box culvert. The stability of the surrounding soil is important to the structural performance of most culverts. Good compaction by the dynamic compaction roller with big capacity is as effective as good backfill materials to increase the structural integrity of culvert. However structural distress of the culvert could be occur due to the excessive earth pressure by dynamic compaction load. In this study, 16 box culverts were constructed with various compaction materials and construction methods. Three types of on-site soils such as subbase, subgrade and roadbed materials were used as backfill materials in the test program. Compaction methods were adapted based on the site conditions. In most cases, dynamic compaction rollers with 10 to 16 ton weights were used and vibration speed were applied from 2400 to 2500 rpm for the great compaction energy. Some backfill compactions with good quality soils were carried out to examine the effect of EPS(Expanded Polystyrene) panels with changes of compaction thickness. This paper presents the main results of the research conducted to access the engineering performance of the backfill materials. The characteristics of earth pressures are discussed. It is observed that subgrade and roadbed materials are needed more careful compaction than subbase materials. It is shown that EPS panels are effective to mitigate dynamic lateral earth pressure on the culverts. It is also obtained that the dynamic pressure depends on the soil properties. In addition, the coefficient of dynamic earth pressure (K$\sub$dyn/=ΔP$\sub$H/ ΔP$\sub$V/) during compaction is discussed.

• 한국지반공학회지:지반
• /
• 제12권4호
• /
• pp.47-60
• /
• 1996

고전 토압이론 중에서 Coulomb 및 Rankine토압이론식을 실무에 주로 사용되고 있는데, 이 들에 의한 토압은 삼각형 분포로 간주하고 있다. 그러나 Terzaghi(1934), Tsagreli(1967), Fang & Ishibashi(1986) 등에 의한 실험결과에서 토압은 삼각형 분포가 아님이 밝혀졌다. 본 연구에서는 흙으로 뒤채움된 지표면이 경사지며, 강성옹벽의 뒷면이 경사진 일반적인 경우에 적용할 수 있는 토압이론식이 아취개념을 사용하여 새로이 제안되었다. 새로이 제안된 이론식에 의한 계산결과는 기존 이론들에 의한 것들과 비교되었으며, 이 이론식에 의하여 토압에 영향을 미치는 요소들을 분석하였다. 비교 및 분석결과를 보면, 전주동토압은 새로이 제안된 이론식에 의한 값이 기존이론에 의한 값들과 잘 일치하였다. 그러나 Rankine이론에 의한 전토압 은 비교된 기타 이론들에 의한 값과 상이하였다. 그리고 작용점 위치(h)는 삼각형 분포의 중심 위치인 0.33이 아니라 옹벽 뒷면의 경사각,뒤채움 지면의 경사각, 흙의 내부마찰각 및 부착력에 의하여 주로 지배되었다.

• 한국지반공학회지:지반
• /
• 제8권4호
• /
• pp.5-16
• /
• 1992

본 연구에서는 다짐 유발응력 (compaction induced stress)을 고려한 보강토 설계방법을 고안하였다. 현행 보강토 설계법은 다짐에 의해 유발되는 횡방향토압을 정량적으로 고려하지 라고 있으므로, 본 연구는 먼저 다짐 유발응력 산정방법을 검토하고 다음에 이를 보강토 설계에 통용 함으로써 새로운 설계방법을 제안하였다. 다짐 유발응력들 고려하면 벽체의 위쪽 부분에 토압이 산정되므로 이 부분에는 인장강도와 인발저항이 큰 보강재 사용이 바람직하다. 이를 위하여 새로이 개발한 보강재 GEOLOG를 소개하였다. 새로운 방법으로 보강토 옹벽을 설계하고 이를 종래의 방법과 비교 분석하여 보강토 공법에 관한 몇가지 결론을 제시하였다.

• 한국지반환경공학회 논문집
• /
• 제12권4호
• /
• pp.43-51
• /
• 2011

연약지반에 시공하는 많은 콘크리트전주가 외부하중으로 전도파괴가 발생하는데 본 연구에서는 실물인장실험을 실시하고 근가위치, 근가깊이, 근가개수, 전주근입깊이를 달리하면서 전주에 작용하는 수평토압을 분석하였다. 실물실험은 10가지 종류로 나누어 실험한 결과 수평토압은 전주 근입깊이가 클수록 커지고 하부수동영역이 길어지는 것으로 나타났다. 근가 설치위치가 깊을수록 하부수동영역 토압이 감소된다. 변위는 근가의 위치 및 수량, 전주기초의 근입깊이에 따라 뚜렷한 차이를 나타냈다. 초기하중 재하 시 상부에서 굴절된 양상을 보이다 점증하중에 따라 전주의 중앙부로 굴절의 양상이 전이되었다. 근가위치는 G.L(-) 0.5m인 상태에서 전주기초 깊이 1.3m를 추가로 근입 시 최대 수평변위는 약 1.6배의 감소를 보여 전주의 안정성이 증가하였다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 1999년도 가을 학술발표회 논문집
• /
• pp.161-168
• /
• 1999

A series of centrifuge model tests were performed in order to investigate the behaviors of various tunnel linings. A 1/100-scaled aluminum and hydrostone horseshoe tunnel linings with a radius km, height km were buried in a depth of C/D=3 with dry Joomunjin standard sand, the relative density of which was 86%. Bending moments and thrusts along the tunnel circumference were measured by 12 strain gages. Earth pressures in soil and on lining were estimated by pressure transducers, ground surface settlements at center and edges by using LVDTs. Average Ko(coefficient of earth pressure at rest) was 0.39 for the model sand. The structural behaviors of lining depended on its damaged conditions. But, as a rule, on the crown, the tensile circumferential strain of lining occurred at the inner surface, and the compressive at the outer surface, then positive bending moment was created at the crown. The circumferential strain of the inner surface on the springline was tensile, and the outer compressive, so negative bending moment was measured at the springline. For hydrostone linings, cracks initiated at the inner surface on the crown, and the outer on the springline over average 40g.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2001년도 The 6th International Symposium of East Asian Resources Recycling Technology
• /
• pp.699-704
• /
• 2001

Until recently, disposal to landfill has been the most convenient way to deal with the increasing amount of residues the shredding industries produce. But the shortage of such disposal sites and the risk that liquid drained from these waste dusts may pollute ground water have increased the environmental pressures to find more effective solutions. The present study is an alternative approach that suggests identifying waste dusts characteristics and selecting an appropriate binder for hazardous materials to reduce the amount of contaminants (mainly lead) that were leaking into the soil. Investigations on the characteristics of automobiles waste dusts show that these materials are composed mainly of cottons and sponge like substances, plastics, rubber, glasses and gravel, metals, and electric wires. Besides, the percentage in weight of organic (inflammable) materials is about 70% and the lead contamination, which has not a ionic but a particulate nature, is particularly remarkable in cottons and sponge like materials. Binding additives such as K-20 and sodium carbonate were not effective but the addition of 5 % of cement (in weight of the investigated sample) followed by a 3-minute stirring and a 4-hour storage could drastically reduce the run off of lead below the maximum authorized level. No addition of water was necessary in this method.

• 한국지반공학회지:지반
• /
• 제4권2호
• /
• pp.25-32
• /
• 1988

본 논문에서는 뒤채움이 사질토이고 수평면인 연직벽이 수평이동변위(ATRA)를 일으킬 때 토류벽에 작용하는 정적 주동토복을 Dubrova방법과 Dubrova방법에 Chang의 개념을 도입시킨 방법 각각으로 구하였다. 이 결과를 최근에 Fang and Ishibashi가 발표한 모형실험결과와 비교분석하였다. 또한 이미 발표한 바 있는 제(1985)의 벽체 정점과 저면을 중심으로 단전하는 정적 주동토압(AT, AB)의 경우도 상기모형실험결과와 비교분석하였다. 그 결과 다음과 같은 결론을 얻었다.

• 한국지반공학회지:지반
• /
• 제13권5호
• /
• pp.19-34
• /
• 1997

Classical earth pressure theories normally assume that ground condition remains uniform for considerable distance from the wall, and that the movement of the wall is enough to result in the development of an active pressure distribution. In the case of many low gravity walls in cut, constructed, for example, by using gabions or cribs, this is not commonly the case. In strong ground a steep temporary face will be excavated for reasons of economy, and a thin wedge of backfill will be placed behind the wall following its construetion. A designer then has the difficulty of selecting appropriate soil parameters and a reasonable method of calculating the earth pressure on the w리1. This paper starts by reviewing the existing solutions applicable to such geometry. A new silo and a wedge methods are developed for static and dynamic cases, and the results obtained from these are compared with two experimental results which more correctly mod el the geometry and strength of the wall, the fill, and the soil condition. Conclusions are drawn concerning both the magnitute and distribution of earth pressures to be supported by such walls.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2008년도 추계 학술발표회
• /
• pp.3-32
• /
• 2008

The potential deep geothermal resources span a wide range of heat sources from the earth, including not only the more easily developed, currently economic hydrothermal resources; but also the earth's deeper, stored thermal energy, which is present anywhere. At shallow depths of 3,000~10,000m, the coincidence of substantial amounts heat in hot rock, fluids that heat up while flowing through the rock and permeability of connected fractures can result in natural hot water reservoirs. Although conventional hydrothermal resources which contain sufficient fluids at high temperatures and geo-pressures are used effectively for both electric and nonelectric applications in the world, they are somewhat limited in their location and ultimate potential for supplying electricity. A large portion of the world's geothermal resource base consists of hot dry rock(HDR) with limited permeability and porosity, an inadquate recharge of fluids and/or insufficient water for heat transport. An alternative known as engineered or enhanced geothermal systems(EGS), to dependence on naturally occurring hydrothermal reservoirs involves human intervention to engineer hydrothermal reservoirs in hot rocks for commercial use. Therefore EGS resources are with enormous potential for primary energy recovery using an engineered heat mining technology, which is designed to extract and utilize the earth's stored inexthermal energy. Because EGS resources have a large potential for the long term, United States focused his effort to provide 100GW of 24-hour-a-day base load electric-generating capacity by 2050.