• The Proceeding of the Korean Institute of Electromagnetic Engineering and Science
• /
• v.7 no.2
• /
• pp.38-45
• /
• 1996

우리의 일상 생활에 있어 가정용 전기기기는 우리 삶의 일부분이라고 말할 수 있을 정도로 그 존재 가치가 절대적이다. 최근 반도체 기술의 발달은 이러한 기기의 제어를 기계적인 방법에서 digital 방식의 전자자적인 방법으로 바꾸어 놓고 있다. 이러한 전자적인 제어장치를 갖는 기기로 의 발전은 사용상의 편리함을 갖고 있는 반면 EMC(Electromagnetic Compactibility)부분에 취약한 단점을 가지고 있다. 특히 가정용 전기기기는 물론이고 전동공구류 또한 일반 가정에서 쉽게 사용 될 수 있는 기기이므로 전자파장해에 대한 문제는 기기의 오동작 문제를 떠나 사용자 신체의 손상 등 위해를 가할수 있는 가능성을 항상 갖고 있다. 가정용 전기기기 및 전동 공구류에 대한 EMC문 제는 장착된 Micro-Processor 구동을 위한 clock 신호, 모터 등 회전기 부분에서 발생하는 불연속 적인 전자파 noise, 전원선에서 발생하는 전도성 noise와 방사성 noise가 그 원인이 되고 있으며 이러한 전자파 noise는 주변에서 동작하고 있는 다른 기기의 동작을 방해하고 또한 주변에서 동작 하고 있는 다른 기기로부터의 전자파 noise에 의해 자신이 영향을 받아 불필요한 오동작을 유발하 기도 한다. 여기에서는 EMI 부분의 경우 금번 고시 내용과 기존의 전기용품 안전관리법의 내용을 비교하였 으며, EMS 부분은 가정용 전기기기 뿐만아니라 고시된 해당 제품 모두를 비교하여 관련 제조업체 및 관계자에게 도움이 되도록 하였다.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.66 no.4
• /
• pp.651-658
• /
• 2017

This paper proposes an analysis method of performance degradation of antenna due to radio frequency interference between an antenna and adjacent noise sources using active scattering parameters. The radio frequency interference can be analyzed by the measured or simulated scattering parameters and by excited noise sources in the circuit as well. In this paper, a planar inverted-F antenna and a noise source are designed and fabricated to analyze radio frequency interference between the planar inverted-F antenna and noise source. The proposed analysis method uses active scattering parameters, of which verification is experimentally verified, and in simulation as well.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.22 no.3
• /
• pp.143-147
• /
• 2014

The ECU which is operating inductive actuator like motor or solenoid should be designed with considering the heat removal performance and the EMC performance. In most cases, these two performances are trade-off. Especially, the metal cover with plastic housing for improving heat removal performance can affect EMC performance by coupling the noise source to harness cable and connector. Therefore, after analyzing the EMC effectiveness of the metal cover, countermeasures for EMC noise reduction should be established. In this paper, by simulating and testing of AHB Gen3 ECU, the influence of the metal cover to EMC performance is analyzed. And based on this result, we propose solutions for EMC noise reduction.

• Proceedings of the KIPE Conference
• /
• 2005.07a
• /
• pp.266-268
• /
• 2005

A new synchronous switch controlled transient current build-up zero voltage switching (TCB-ZVS) forward converter is proposed. The proposed converter is suitable for the low-voltage and high-current applications. The features of the proposed converter are low conduction loss of magnetizing current, no additional circuit for the ZVS operation, high efficiency, high power density and low EMI noise throughout all load conditions.

• Journal of Electrical Engineering and Technology
• /
• v.13 no.1
• /
• pp.532-532
• /
• 2018

This article has been retracted at the request of the authors and/or the Editor in Chief. Reason: After the paper published, the authors have found that the intellectual property for this paper was a company's own. As a result, the authors have elected to withdraw the complete article with apologies to the scientific community

• Journal of Electrical Engineering and Technology
• /
• v.9 no.5
• /
• pp.1724-1728
• /
• 2014

Heat sink has been used to help an electrical device operate in normal temperature condition. But heat sink radiates unwanted electromagnetic wave, which may cause electromagnetic interference problem. A resistance loaded grounding technique is proposed to reduce electromagnetic wave radiation by a heat sink. Numerical simulations are accomplished to find optimal loading resistance. Also electromagnetic fields radiated by from a heat sink are measured and compared with the simulation results. The test results verify the usefulness of the proposed technique.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.10 no.1
• /
• pp.27-32
• /
• 2015

In this paper, a mushroom typed electromagnetic band gap (EBG) structure to be inserted in the printed circuit board (PCB) inner layer in order to stabilize the PCB power line is proposed for global-navigation satellite service (GNSS). In designing the proposed EBG structure, the target stop-bandwidth was designed from 1.55GHz to 1.81GHz including GNSS and mobile communication-related frequency bandwidth. In this bandwidth, the insertion loss(S21) was observed below about -40dB. From the simulation results, it is expected that the stabilization of power delivery network (PDN) structure in the PCB circuit design should be improved and the effective correspondence to EMI will be helpful.

• KIEE International Transaction on Electrical Machinery and Energy Conversion Systems
• /
• v.3B no.3
• /
• pp.147-154
• /
• 2003

This paper presents a high-frequency boost type ZVS-PWM chopper-fed DC-DC power converter with a single active auxiliary edge-resonant snubber at the load stage which can be designed for power conditioners such as solar photovoltaic generation, fuel cell generation, battery and super capacitor energy storages. Its principle operation in steady-state is described in addition to a prototype setup. The experimental results of boost type ZVS-PWM chopper proposed here, are evaluated and verified with a practical design model in terms of its switching voltage and current waveforms, the switching v-i trajectory and the temperature performance of IGBT module, the actual power conversion efficiency, and the EMI of radiated and conducted emissions, and then discussed and compared with the hard switching scheme from an experimental point of view. Finally, this paper proposes a practical method to suppress parasitic oscillation due to the active auxiliary resonant switch at ZCS turn-off mode transition with the aid of an additional lossless clamping diode loop, and can be reduced the EMI conducted emission.

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.2152_2153
• /
• 2009

In this study, the dynamic characteristic of a contact wire and pantograph suppling electrical power to high-speed trains are investigated from an electrical response point of view. To analysis power line disturbance by induced contact loss phenomenon for high speed operation, a hardware Simulator which considered contact loss between contact wire and the pantograph as well as contact wire deviation is developed. It is confirmed that a contact wire and pantograph model are necessary for studying the dynamic behavior of the pantograph system. One of the most important needs accompanied by increasing the speed of high-speed train is reduced that an arc phenomenon by loss of contact brings out EMI. In case of a high-speed train using electrical power, as comparison with diesel rolling stock, PLD(Power Line Disturbance) such as harmonic, transient voltage and current, EMI, dummy signal injection etc usually occurs. Throughout experiment, it is verified that an arc phenomenon is brought out for simulator operation and consequently conducted noise is flowed in electric circuit by power line disturbance.

• Proceedings of the KIEE Conference
• /
• 2001.05a
• /
• pp.194-196
• /
• 2001

Light dimming is based on adjusting the voltage which gets to the lamp. Light dimming has been possible for many decades by using adjustable power resistors and adjustable transformers. The power electronics have proceeded quietly since 1960. Between 1960-1970 thyristors and triacs came to market. Using those components it was quite easy to make small and inexpensive light dimmers which have goof efficiency. This type of electronic light dimmers became available after 1970 and are nowadays used in very many locations like homes, restaurants, conference rooms and in stage lighting. But the problem of thyristor dimmer have been that it has poor efficiency and voltage drop. Recently IGBT(Insulated Gate Bipolar Transistor) control is a new way to do light dimming for improving this problems. IGBT dimmer has many other advantages over traditional thyristor dimmer there are no huge current spikes and EMI caused by turn on Using IGBT it is possible to make the turn-off rate relatively slot to achieve quite operations in terms of EMI and acoustical or incandescent lamp filament noise. For the development of IGBT dimmer. This paper shows the effects of IGBT dimmer compared with thyristor dimmer through a simulation using EMTDC.