• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.42 no.10
• /
• pp.878-883
• /
• 2014

This paper presents the test result of system level EMC of LEO satellite Deimos-2 FM that has been launched in June 20, 2014. The Deimos-2 satellite was designed considering the EMC of unit modules level in addition to the structure aspects. The Auto-Compatibility, Radiated Emission and Radiated Susceptibility test was conducted. The test result has meet the standard of system EMC of Deimos-2 program.

• Journal of Korean Society of Environmental Engineers
• /
• v.34 no.8
• /
• pp.557-565
• /
• 2012

In this research, it was analyzed that the effect of the non-point source pollution that occurs in the lower reaches of the livestock area. The analysis on the hydro- and polluto-graphs showed that the concentration of pollution gradually increased as the flow rate increased and, after reaching the peak flow rate, the flow rate dropped drastically. For Event Mean Concentration (EMC), in the lower reaches of livestock area, TSS EMC was 146.80~424.95 mg/L, COD EMC 11.64~55.66 mg/L, BOD EMC 6.66~49.88 mg/L, T-N EMC 7.650~43.825 mg/L and T-P EMC 0.711~3.855 mg/L. According to the results of the analysis on the correlations between pollutants, TSS and BOD, COD, T-N and T-P had correlations at a 0.53~0.95 confidence level. In addition, according to the result of the analysis on the correlations between EMC (mg/L) and storm runoff ($m^3$), the correlation was well explained by a Cubic regression. In addition, among the determination coefficients, TSS and T-N were relatively high, at 0.767~0.835 and 0.773~0.901 respectively, which indicates that EMC goes up as the storm runoff increases. Therefore, it is expected that EMC can be forecasted according to the amount of runoff ($m^3$). The results of this research will be a practical information for the assessment of the non-point source pollution that occurs in the lower reaches of the livestock area.

• Korean Journal of Materials Research
• /
• v.9 no.10
• /
• pp.992-999
• /
• 1999

Due to the inherently poor adhesion strength of Cu-based leadframe/EMC(Epoxy Molding Compound) interface, popcorn-cracking phenomena of thin plastic packages frequently occur during the solder reflow process. In this study, in order to enhance the adhesion strength of Cu-based leadframe/EMC interface, brown-oxide layer was formed on the leadframe surface by immersing of leadframe sheets in hot alkaline solution, and the adhesion strength of leadframe/EMC interface was measured by using SDCB(Sandwiched Double Cantilever Beam) and SBN(Sandwiched Brazil-Nut) specimens. Results showed that brown oxide treatment of leadframe introduced fine acicular CuO crystals on the leadframe surface and improved the adhesion strength of leadframe/EMC interface. Enhancement of adhesion strength was directly related to the thickening kinetics of oxide layer. This might be due to the mechanical interlocking of fine acicular CuO crystals into EMC.

• BMB Reports
• /
• v.50 no.8
• /
• pp.411-416
• /
• 2017

The endoplasmic reticulum (ER) membrane protein complex subunit 6 (EMC6) is a novel human autophagy-related molecule. Here, using tissue microarray and immunohistochemistry, we report that EMC6 protein is lost or reduced in glandular cells of patients with gastric adenocarcinoma, compared to normal stomach mucosa. Overexpression of EMC6 in gastric cancer cells inhibited cell growth, migration, invasion, and induced apoptosis and cell cycle arrest at S-phase. Further investigation suggested that EMC6 overexpression in BGC823 human adenocarcinoma gastric cancer cells reduced tumorigenicity in a xenograft model, demonstrating that EMC6 has the characteristics of a tumor suppressor. This is the first study to show that EMC6 induces cell death in gastric cancer cells. The molecular mechanism of how EMC6 functions as a tumor suppressor needs to be further explored.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.11
• /
• pp.6419-6424
• /
• 2014

The use of the PMP (Protection Module Package) was proposed as a solution for the shorter battery lifetime. The PMP means that a protection circuit consists of a semiconductor single. In this study, basic research was carried out to select a suitable epoxy material of the EMC module through finite element analysis. First, the stress on the external force was compared by the flexural strength analysis. In the following thermal analysis, the temperature change of the EMC module and the internal part was compared using the calculated heating value. Finally, the filling ratio was compared with the injection of the melting epoxy in the EMC module.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.22 no.3
• /
• pp.143-147
• /
• 2014

The ECU which is operating inductive actuator like motor or solenoid should be designed with considering the heat removal performance and the EMC performance. In most cases, these two performances are trade-off. Especially, the metal cover with plastic housing for improving heat removal performance can affect EMC performance by coupling the noise source to harness cable and connector. Therefore, after analyzing the EMC effectiveness of the metal cover, countermeasures for EMC noise reduction should be established. In this paper, by simulating and testing of AHB Gen3 ECU, the influence of the metal cover to EMC performance is analyzed. And based on this result, we propose solutions for EMC noise reduction.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.32 no.3
• /
• pp.57-66
• /
• 2024

In this study, silicon sludge from a semiconductor packaging process is recycled to fabricate silica coated silicon-sludge and applied as a filler for an epoxy molding compound(EMC). Silicon-sludge powder(S-sludge) is treated with acid to remove metallic impurities and then coated using the sol-gel method to synthesize silica coated silicon-sludge powder(SS-sludge). The as-synthesized SS-sludge is subsequently mixed with epoxy resin, a curing agent, and carbon black to create an EMC(SS-sludge EMC). The heat dissipation properties of the EMC were examined using an IR camera. IR camera analysis confirmed that the SS-sludge EMC exhibited the highest surface temperature of 58.5℃ compared to SiO₂-based EMC. This enhancement in heat dissipation using SS-sludge EMC is attributed to the excellent thermal conductivity(150W/mK) of the silicon substrate and the presence of the silica layer on the SS-sludge surface which effectively enhances the thermal property of the EMC. Therefore, this study successfully demonstrates the recycling of silicon sludge from a semiconductor packaging process by synthesizing silica coated silicon-sludge and suggests a novel application of this material in semiconductor packaging.

• Korean Journal of Construction Engineering and Management
• /
• v.7 no.3 s.31
• /
• pp.149-158
• /
• 2006

For construction projects, it is required to estimate the Environmental Management Cost(EMC) for pollution prevention, using the calculation standards prescribed in the Construction Technology Management Law(CTML). However, the EMC standards are difficult to utilize without definite site information. Therefore, it is needed a new calculation method reflecting project site information. According to the definition of EMC in the CTML, this study identifies the EMC items and classifies them into the pollution types such as air, water, noise, waste and others. With this EMC classification, the stud:』 analyzes using the SPSS the EMC for the 78 new multi-housing projects, which were executed during the past three years, 2000-2002. And then an EMC estimating matrix is developed with simple information such as site location and size of area from historical data. The proposed matrix can be effectively used to check and control budgeting and estimating the EMC of the multi-housing projects. In addition, the proposed EMC matrix are validated through a case study.

• Journal of Navigation and Port Research
• /
• v.26 no.5
• /
• pp.525-528
• /
• 2002

The proposed EMC filter composed with feed-through capacitors and ferrite beads of high permeability was prepared which satisfy the EMC standard for a wide-band noise signal in the frequence of 10 MHz to 1.5 GHz in power supply line. The optimum structure of ferrite bead was found by calculating the load effect of ferrite beads. As a result, the filter showed excellent differential- and common-mode noises filtering characteristics above 30dB in the frequency band from 10 MHz to 1.5 GHz. The immunity characteristics are improved more than 10 to 30 dB over the frequency band from DC to 1.8GHz.

• Proceedings of the KIEE Conference
• /
• 2002.07a
• /
• pp.524-526
• /
• 2002

본 논문에서는 전력계통 관련 기기에서 문제가 되고 있는 전자기적합성(Electromagnetic Compatibility, 이하 EMC)을 다루고자 한다. 전력계통은 서지와 같은 많은 전자기 장해를 발생한다. 그래서 최근 제정 및 개정되고 있는 전자기기 회로가 포함되어 있는 IEC 규격에서는 대부분 EMC 시험을 포함하고 있다. 본 논문에서는 전력계통과 EMC 연관성을 검토하고자 한다. 또한 주요 중전기기의 EMC 규격 동향을 소개하고자 한다. 마지막으로 국내 전력계통 기기에서 발생한 실제 EMC 문제를 소개하고자 한다.