• Applied Chemistry for Engineering
• /
• v.33 no.3
• /
• pp.289-295
• /
• 2022

In this study, we intend to fabricate an all solid polymer battery with a reduced interfacial resistance between the solid electrolyte and the electrode by applying thiophene based polymers as both electrode and electrolyte materials. In order to minimize the interfacial resistance with the poly(3,4-ethylenedioxy thiophene) (PEDOT) based electrode, 3,4-ethylenedioxy thiophene (EDOT) oligomer was introduced into the solid electrolyte. Also, to improve the lithium salt dissociation ability of the EDOT oligomer [oligo(EDOT)] electrolyte, it was blended with poly(vinylidene fluoride) (PVdF). As a result, the ionic conductivity of the solid polymer electrolyte increased by introducing PVdF into the oligo (EDOT). From the result of evaluating the electrochemical properties of an all solid polymer battery, the interfacial resistance significantly decreased by introducing a thiophene based polymer to the electrode and electrolyte.

• Macromolecular Research
• /
• v.17 no.9
• /
• pp.714-717
• /
• 2009

Hole transport copolymers consisting of 3,4-ethylenedioxythiophene (EDOT) and N-4-butylphenyl-N,N-diphenylamine (BTPA) were synthesized by oxidative coupling reaction using $FeCl_3$ as an oxidant. These copolymers showed good solubility and their thin films showed sufficient morphological stability. The copolymers showed an absorption maximum around 320 nm. Copolymers had an oxidation peak at approximately $1.03{\sim}1.14V$ versus the Ag/AgCl electrode. The hole mobility increased with increasing portion of the EDOT unit. The hole mobility of the copolymer containing 57% of the EDOT unit showed the highest mobility of $3{\times}10^{-5}cm^2/V{\cdot}s$.

• Applied Chemistry for Engineering
• /
• v.27 no.1
• /
• pp.45-49
• /
• 2016

In the presence of poly(4-styrene sulfonate) (PSS) and excess amount of graphene oxide (GO), we conducted in-situ polymerization of 3,4-ethylenedioxythiophene (EDOT) without an oxidant. XPS and IR spectroscopies of the product (GO-P) showed that PEDOT/PSS was successfully synthesized by oxidative polymerization of EDOT and hybridized with GO. GO-P displayed a stable aqueous suspension, however, the high content (42%) of GO in GO-P diminished electrical conductivity down to $15S{\cdot}m^{-1}$. Annealing of GO-P films at $200^{\circ}C$ for 8 hr induced partial reduction of GO and finally enhanced electrical conductivity up to $212S{\cdot}m^{-1}$.

• Macromolecular Research
• /
• v.17 no.10
• /
• pp.791-796
• /
• 2009

An electrochemically and photochemically polymerizable monomer, 2-((2,3-dihydrothieno[3,4-b] [1,4]dioxin-2-yl)methoxy)ethyl methacrylate (EDOT-EMA), was explored for patterning of poly(3,4-ethylenedioxythiophene) (PEDOT) via side chain cross-linking. The polymer from EDOT-EMA was deposited electrochemically to produce polymeric EDOT (PEDOT-EMA), which was directly photo-patterned by UV light as the side EMA groups of PEDOT-EMA were polymerized to give cross-linked EMA (PEDOT-PEMA). Absorption and FTIR studies of the UV-exposed film (PEDOT-PEMA) indicated that the photo-patterning mainly originated from the photo cross-linking of the methacrylates in the side-chain. After irradiation of the film, the conductivity of the irradiated area decreased from $5.6{\times}10^{-3}$ S/cm to $7.2{\times}10^{-4}$ S/cm, possibly due to bending of the conductive PEDOT channel as a result of the side chain cross-linking. The patterned film was applied to a solid state electrochromic (EC) cell to obtain micro-patterned EC cells with lines up to 5 ${\mu}m$ wide.

• Journal of Information Display
• /
• v.5 no.4
• /
• pp.12-17
• /
• 2004

A series of statistical random copolymers of dioctylfluorene (DOF) and 3,4-ethylenedioxythiophene (EDOT) were synthesized by Ni (0) mediated polymerization and their light-emitting properties were compared with poly (9,9-di-n-octylfluorene) (PDOF). The synthesized polymers were characterized using UV-vis spectroscopy, TGA, photoluminescence (PL) & electroluminescence (EL) spectroscopy and by conducting molecular weight studies. The resulting polymers were found to be thermally stable and readily soluble in organic solvents. The UV-visible absorption and PL emission spectra of the copolymers were gradually red-shifted as the fraction of EDOT in copolymers increased. Light-emitting devices were fabricated in an ITO (indium-tin oxide)/PEDOT/polymer/Ca/Al configuration. Interestingly, the EL spectra of these devices were similar to the PL spectra of the corresponding polymer film. However, the EL devices constructed from the copolymer showed more than 10 times higher efficiency level than the devices constructed from the PDOF homopolymer. This higher efficiency is possibly the result of better charge carrier balance in the copolymer systems due to the lower HOMO levels of the copolymers in comparison to that of PDOF homopolymer.

• Bulletin of the Korean Chemical Society
• /
• v.30 no.5
• /
• pp.1207-1210
• /
• 2009

• Polymer(Korea)
• /
• v.33 no.5
• /
• pp.452-457
• /
• 2009

Hybrid nanomaterials consisting of multi-walled carbon nanotube(MWNT) and/or PEDOT of conductive polymer were prepared in this study. In the presence of catalyst and ligand, the MWNT-Br compound prepared by the successive surface treatment reaction was mixed with MMA to initiate the atom transfer radical polymerization process. PMMA was covalently linked to the surface of MWNT for the formation of MWNT/PMMA nanocomposites. The EDOT and oxidant were added in the aqueous emulsion of PS produced via a miniemulsion polymerization process and then it proceeded to carry out the oxidative chemical polymerization of EDOT for the preparation of PEDOT/PS nanoparticles with the core-shell structure. The aqueous dispersion of PEDOT:poly(styrene sulfonate) (PSS) was mixed with the silica particles treated with a silane compound and thus PEDOT:PSS-clad silica nanoparticles were prepared by the surface chemistry reaction. The hybrid nanomaterials were analyzed by using TEM, FE-SEM, TGA, EDX, UV, and FT-IR.

• Polymer(Korea)
• /
• v.38 no.6
• /
• pp.809-814
• /
• 2014

An array structure of conducting polymer microtubule was fabricated for an amperometric biosensor. 3,4-Ethylenedioxythiophene (EDOT) was electropolymerized in the microporous template membrane with poly(3,4-ethylenedioxythiophene)/poly(4-styrenesulfonic acid) (PEDOT/PSS) composite as a binder. The array structure can provide enhanced current collecting capability due to large active surface area compared to the macroscopic area of the electrode itself. For a biosensor application, the array electrode was tested for $H_2O_2$ detection and showed very sluggish electrochemical response to $H_2O_2$. To enhance the detection efficiency to the oxidation of $H_2O_2$, gold was treated on the electrode by two different approaches: sputtering and electrochemical deposition. Gold treatment with either method greatly enhanced the sensitivity of the electrode to $H_2O_2$. So, conducting polymer microtubule array with gold treatment was expected to be a sensitive amperometric biosensor system based on the detection of $H_2O_2$.

• Bulletin of the Korean Chemical Society
• /
• v.32 no.7
• /
• pp.2446-2448
• /
• 2011

• Bulletin of the Korean Chemical Society
• /
• v.33 no.8
• /
• pp.2529-2534
• /
• 2012

Poly(3,4-ethylenedioxythiophene) coated Manganese Dioxide (PEDOT/$MnO_2$) composite electrode was fabricated by simply immersing the $MnO_2$ electrode in an acidic aqueous solution containing 3,4-ethylenedioxythiophene (EDOT) monomers. Analysis of open-circuit potential of the $MnO_2$ electrode in the solution indicates the reduction of outer surface of $MnO_2$ to dissolved $Mn^{2+}$ ions and simultaneously oxidation of EDOT monomer to PEDOT on the $MnO_2$ surface to form a PEDOT shell via a galvanic displacement reaction. Analysis of cyclic voltammograms and specific capacitance of the PEDOT/$MnO_2$, conductive carbon added $MnO_2$ and conductive carbon added PEDOT/$MnO_2$ electrodes suggests that the conductive carbon acted mainly to provide a continuous conducting path in the electrode to improve the rate capability and the PEDOT layer on $MnO_2$ acts to increase the active reaction site of $MnO_2$.