• Journal of Korean Society of Forest Science
• /
• v.9 no.1
• /
• pp.1-44
• /
• 1969

The important results which have been obtained in the investigation can be recapitulated as follows. 1. As demostrated by the experimental results and analyses concerning their effects in the on-ground type mushroom house, the constructions in relation to the side wall and ceiling of the experimental houses showed a sufficient heat insulation on effect to protect insides of the houses from outside climatic conditions. 2. As the effect on the solar type experimental mushroom house which was constructed in a half basement has been shown by the experimental results and analyses, it has been proved to be effective for making use of solar heat. However there were found two problems to be improved for putting solar houses to practical use in the farm mushroom growing: (1) the construction of the roof and ceiling should be the same as for the on-ground type house, and (2) the solar heat generating system should be reconstructed properly. A trial solar heat generating system is shown in Fig. 40. 3. Among several ventilation systems which have been studied in the experiments, the underground earthen pipe and ceiling ventilation, and vertical side wall and ceiling ventilation systems have been proved to be most effective for natural ventilation. 4. The experimental results have shown that ventilation systems such as the vertical side wall and underground ventilation systems are suitable to put to practical use as natural ventilation systems for farm mushroom houses. These ventilation systems can remarkably improve the temperature of fresh air which is introduced into the house by heat transfers within the ventilation passages, so as to approach to the desired temperature of the house without any cooling or heating operation. For example, if it is assuming that x is the outside temperature and y is the amount of temperature adjustment made by the influence of the ventilation system, the relationships that exist between x and y can be expressed by the following regression lines. Underground iron pipe ventilation system ${\cdots}{\cdots}$ y=0.9x-12.8 Underground earthen pipe ventilation system ${\cdots}{\cdots}$y=0.96x-15.11 Vertical side wall ventilation system${\cdots}{\cdots}$ y=0.94x-17.57 5. The experimental results have shown that the relationships existing between the admitted and expelled air and the $Co_2$ concentration can be described with experimental regression lines or an exponent equation as follows: 1) If it is assumed that x is an air speed cm/sec. and y is an expelled air speed in cm/sec. in a natural ventilation system, since the y is a function of the x, the relationships that exist between x and y can be expressed by the regression lines shown below: 2) If it is assumed that x is an admitted volume of air in $m^3/hr$ and y is an expelled volume of air in $m^3/hr$ in a natural ventilation system, since the y is a function of the x, the relationships that exist between x and y can be expressed by the regression lines shown below. 3) If it is assumed that the expelled air speed in cm/sec and replacement air speed in cm/sec. at the bed surface in a natural ventilation system are shown as x and y, respectively, since the y is a function of the x, the relationships that exist between x and y can be expressed by the following regression line: G.E. (100%)- C.V. (50%) ventilation system${\cdots}$ y=0.54X+0.84 4) If it is assumed that the replacement air speed in cm/sec. at the bed surface is shown as x, and $CO_2$ concentration which is expressed by multiplying 1000 times the actual value of $CO_2$ % is shown as y, in a natural ventilation system, since the y is a function of the x the relationships that exist between x and y can be expressed by the following regression line: G.E. (100%)- C.V. (50%) ventilation system${\cdots}{\cdots}$ y=114.53-6.42x 5) If it is assumed that the expelled volume of air is shown as x and the $CO_2$ concentration which is expressed by multiplying 1000 times the actual of $CO_2$ % is shown as y in a natural ventilation system, since the y is a function of of the x, the relationships that exist between x and y can be expressed by the following exponent equation: G.E. (100%)-C.V. (50%) ventilation system${\cdots}{\cdots}$ $$y=127.18{\times}1.0093^{-X}$$ 6. The experimental results have shown that the ratios of the crass sectional area of the G.E. and C.V. vent to the total cubic capacity of the house, required for providing an adequate amount of air in a natural ventilation system, can be estimated as follows: G.E. (admitting vent of the underground ventilation)${\cdots}{\cdots}$ 0.30-0.5% (controllable) C.V. (expelling vent of the ceiling ventilation)${\cdots}{\cdots}$ 0.8-1.0% (controllable) 7. Among several heating devices which were studied in the experiments, the hot-water boilor which was modified to be fitted both as hot-water toiler and as a pressureless steam-water was found most suitable for farm mushroom growing.

• Journal of Korean Academy of Nursing
• /
• v.1 no.1
• /
• pp.27-43
• /
• 1970

This study is designed to find out proper nursing activities for the needs of the colostomy patients, i.e., mental and psychological as well as physical needs for rapid recovery, and to help them build up the follow-up care for proper social adjustment. The study is based on 268 cases out of 381 colostomy patient's records kept in Ewha Womans University Hospital, Yonsei Medical Center, and National Medical Center in between the period from Jan. 1953 to Jan. 1970. The items of study are mainly on etiology, sex, age, duration of hospitalization, mortality rate, seasonal frequency, time from the onset of illness to the admission of the hospital, signs and symptoms. 1. Frequency of onset by etiology: Neoplastic disease 112 cases (42%), Inflammatory disease 33 cases (12%), Congenital malformation 30 cases (11%), Intussusception 25 cases (9.3%), Trauma 24 cases (9%), Volvulus 17 cases (6.3%), and Crohn's disease 6 cases (2.2%). 2. By sex: male 167 cases (62.9%), and female 101 cases (37.1%). So the ratio of portion of male and female 2:1. 3. By age: under 1·year·old 27 cases (10.1%) highest, 41-50 yrs 54 cases (20.2%), 51-60 yrs 42 cases (15.5%), above 71 yrs 5 cases (1.9%). 4. Duration of hospitalization: the shortest is 2-days and the longest is 470 days. 1-20-days 52%, 40-60 days 14%. 5. Mortality rate: Under the 10-days-admission 19.5%, and the beyond 30-days-admission 3.9%. 6. Seasonal frequency: Higher in summer (32% ). 7. Signs and symptoms: abdominal pain (56%), abdominal distention (54%), vomiting (40%), bloody mucoid diarrhea (38%) , pain of anal region (18%), abdominal tenderness, anorexia, indigestion, constipation, disuria, tenesmus, high fever and chilling sensation, bile tingled vomiting. Nursing activities for the patient's physical needs are as follows: Skin care for colostomy region, Prevention of colostomy constriction and depression, Removal of an offensive odor, The use of colostomy bag-selection for, and demonstration of the use of inexpensive colostomy irrigation equipment, Personal hygiene, general skin care, care of hair, finger nails and toe-nails, Oral hygiene, sleep and rest, aquate, Daily activities, etc. Measures for regulation of bowl movement. Keeping the instruction of taking food, Preparing the meal and help for anorexia, Constipation and it's solution, Prevention of diarrhea, helping the removal of mucous, and stretch constricted steam as needed. Nursing activities for pt's socio-psychological needs are as follows; Help the patient to make decision for the operation, Remove pt's anxiety toward operation and anesthesia, To meet the pt's spiritual needs at his death bed, Help to establish family and friends cooperation, Help to reduce anxiety at the time of admission and it's solution, Help to meet religious need, Help to remove pt's anxiety for loosing his job and family maintenance, Follow-up studies for 7 cases have been done to implement the present thesis. The items of the personal interviews with the patients are as follows: Acceptability for artificial anus, The most anxious thing they had in mind at the time of discharge, The most anxious thing they hat·e in mind at present, Their friends and family's attitudes toward the patient after operation, Relations with other colostomy patients, Emotional damage from the operation, Physical problem of enema, irrigation, Control of diet, Skin care, Control of offensive odor, Patient's suggestions to nurses during hospital stay and after discharge. In conclusion, the follow-up care for colostomy patients shares equal weight or perhaps more than the post-operative care. The follow-up care should include the spiritual care for moral support of the patient, to drag him out of isolation and estrangement, and make him fully participate in social activities. It is suggested that the following measures would help to rehabilitate the colostomy patients (1) mutual acquaintance with other colostomy patients if possible form a sort of club for the colostomy patient to exchange their experiences in care (2) through the team work of doctor, nurse and rehabilitation specialists, to have a sort of concerted effort for betterment of the patient.

• Nuclear Engineering and Technology
• /
• v.39 no.5
• /
• pp.603-616
• /
• 2007

Roy Huddle, having invented the coated particle in Harwell 1957, stated in the early 1970s that we know now everything about particles and coatings and should be going over to deal with other problems. This was on the occasion of the Dragon fuel performance information meeting London 1973: How wrong a genius be! It took until 1978 that really good particles were made in Germany, then during the Japanese HTTR production in the 1990s and finally the Chinese 2000-2001 campaign for HTR-10. Here, we present a review of history and present status. Today, good fuel is measured by different standards from the seventies: where $9*10^{-4}$ initial free heavy metal fraction was typical for early AVR carbide fuel and $3*10^{-4}$ initial free heavy metal fraction was acceptable for oxide fuel in THTR, we insist on values more than an order of magnitude below this value today. Half a percent of particle failure at the end-of-irradiation, another ancient standard, is not even acceptable today, even for the most severe accidents. While legislation and licensing has not changed, one of the reasons we insist on these improvements is the preference for passive systems rather than active controls of earlier times. After renewed HTGR interest, we are reporting about the start of new or reactivated coated particle work in several parts of the world, considering the aspects of designs/ traditional and new materials, manufacturing technologies/ quality control quality assurance, irradiation and accident performance, modeling and performance predictions, and fuel cycle aspects and spent fuel treatment. In very general terms, the coated particle should be strong, reliable, retentive, and affordable. These properties have to be quantified and will be eventually optimized for a specific application system. Results obtained so far indicate that the same particle can be used for steam cycle applications with $700-750^{\circ}C$ helium coolant gas exit, for gas turbine applications at $850-900^{\circ}C$ and for process heat/hydrogen generation applications with $950^{\circ}C$ outlet temperatures. There is a clear set of standards for modem high quality fuel in terms of low levels of heavy metal contamination, manufacture-induced particle defects during fuel body and fuel element making, irradiation/accident induced particle failures and limits on fission product release from intact particles. While gas-cooled reactor design is still open-ended with blocks for the prismatic and spherical fuel elements for the pebble-bed design, there is near worldwide agreement on high quality fuel: a $500{\mu}m$ diameter $UO_2$ kernel of 10% enrichment is surrounded by a $100{\mu}m$ thick sacrificial buffer layer to be followed by a dense inner pyrocarbon layer, a high quality silicon carbide layer of $35{\mu}m$ thickness and theoretical density and another outer pyrocarbon layer. Good performance has been demonstrated both under operational and under accident conditions, i.e. to 10% FIMA and maximum $1600^{\circ}C$ afterwards. And it is the wide-ranging demonstration experience that makes this particle superior. Recommendations are made for further work: 1. Generation of data for presently manufactured materials, e.g. SiC strength and strength distribution, PyC creep and shrinkage and many more material data sets. 2. Renewed start of irradiation and accident testing of modem coated particle fuel. 3. Analysis of existing and newly created data with a view to demonstrate satisfactory performance at burnups beyond 10% FIMA and complete fission product retention even in accidents that go beyond $1600^{\circ}C$ for a short period of time. This work should proceed at both national and international level.

• Korean Journal of Soil Science and Fertilizer
• /
• v.21 no.2
• /
• pp.183-193
• /
• 1988

The relationship between the sulfur fertilization, and the quality and yield of garlic was investigated. The garlic was grown in pot and field at the five fertilization levels of sulfur. The growth characteristics, yield and flavour components of the garlic were studied. The results were summarized as follows; 1. The sulfur applications contributed to a weight and yield of the bulb in SP-10 (10kg/10a) and SF-20 (20kg/10a) significantly, respectively. 2. From the volatile oil obtained by steam distillation of garlic, fourteen organie sulfur components were separated, identified and quantified by GC and GC/MASS and the SP-10 and SF-20 were higher in the concentration of the flavour components in the volatile oil than other treatments. 3. It is considered that the organic sulfur components were synthesized in the top and transported to the bulb of the garlic. 4. In conclusion, SF-20, 20kg/sulfur per 10a, could be recommended to get maximum yield and a good quality of garlic in view of evaluation through the contents of organic sulfur components in the volatile oil and the yield of the bulb.

• Journal of Fisheries and Marine Sciences Education
• /
• v.25 no.6
• /
• pp.1348-1359
• /
• 2013

Kwamaegi is made from the flesh of Pacific saury, Cololabis Saira, which is traditional Korean seafood. It is well-recognized as a valuable health food containing EPA(eicosapentaenoic acid) and DHA(docosahexaenoic acid) to be known ${\omega}$-3 fatty acid. This study was conducted to obtain basic data which can be applied to process of canned Kwamaegi using tomato paste sauce. Commercial Kwamaegi was cut into $2{\times}3cm$ lengths, filled 90 g into can (301-3), added with 60 g water and then precooked for 10 min. at $100^{\circ}C$. After precooking, water was drained. The precooked Kwamaegi was packed into the can, and added with 60 g of tomato paste sauce(tomato paste 42%, gum guar 1.0%, salt 2.0%, starch syrup 2.0%, cooking wine 1%, water 52%). The cans were seamed using a vacuum seamer, and then sterilized for various Fo values (Fo 8~12 min.) in a steam system retort at $121^{\circ}C$. pH, VBN, amino-N, total amino acid, free amino acid, color value (L, a, b), texture profile, TBA value, mineral, sensory evaluation and viable bacterial count of the canned Kwamaegi using tomato paste sauce produced at various sterilization condition(Fo 8~12 min.) were measured. There was no remarkable difference between sterilization conditions and sensual characteristics. The results showed that the product sterilized at Fo 8 min. was the most desirable because this condition is the most economical and tasty.

• Journal of Fisheries and Marine Sciences Education
• /
• v.23 no.3
• /
• pp.410-424
• /
• 2011

This study was investigated for the purpose of obtaining basic data which can be applied to processing of canned sea mussel using tomato paste. Shell were washed, and then steamed and shucked. Sea mussel meat was prepared with ratio of sea mussel 90g, tomato paste sauce 65g(tomato paste 42%, gum guar 1.0%, salt 2.0%, starch syrup 2.0%, cooking wine 1%, water 52%). The sea mussel meats were packed with vacuum seamer in 301-3 can, and then sterilized for various F0 value(F0 8-12 min.) in a steam system retort at $118^{\circ}C$. The factors such as pH, VBN, amino-N, total amino acid, free amino acid, chemical composition, color value (L, a, b), texture profile, TBA value, mineral, sensory evaluation and viable bacterial count of the canned sea mussel produced with various sterilization condition(F0 8-12 min.) were measured. The same element was also measured during preservation. The results showed that the product sterilized at F0 8 min. and preserved for 90 days were the most desirable.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.37 no.3
• /
• pp.199-210
• /
• 2011

This study was conducted to develop functional sources of herbal cosmetics for treatment of skin aging and inflammatory disorders using volatile flavor extracts of four different herbal medicinal prescriptions including Cnidium officinale Makino (COM), Angelica gigas Nakai (AGN), Mentha arvense L. (MAL), Artemisiae argyi Folium (AAF), Paeonia lactiflora Pall (PLP), Rehmanniae Radix Preparata (RRP), Scutellaria baicalensis Georgi (SBG), Panax ginseng C.A. Meyer (PGM), Glycyrrhiza uralensis Fisch (GUF). The volatile flavor extracts of four different herbal medicinal prescriptions (HH-1: COM, AGN, PLP, RRP, HH-2: COM, AGN, PLP, RRP, SBG, PGM, GUF, HH-3: COM, AGN, MAL, AAF, HH-4: COM, AGN, MAL, AAF, SBG, PGM, GUF) were extracted using SDE and their antioxidant and anti-inflammatory effects were measured by using DPPH radical and SLO, respectively. As a result, HH-2 showed moderate DPPH radical scavenging activity (68.24 %) and the strongest SLO inhibitory activity (83.96 %) at 100 ${\mu}g$/mL. Moreover, HH-2 of four different prescriptions significantly inhibited NO production on LPS-stimulated RAW 264.7 cells in a dose-dependent manner without considerable cell cytotoxicity at range of 2.0 ~ 50 ${\mu}g$/mL. Additionally, HH-2 also effectively suppressed the production of $PGE_2$ and IL-6, which are responsible for promoting the inflammatory process. Major volatile components of HH-2 were identified as eugenol, paeonol, butyl phthalide, ${\beta}$-eudesmol and butylidene dihydrophthalide by GC-MS analysis. Thus, these results suggest that HH-2 may be useful as a potential source of anti-inflammatory agents in herbal medicinal cosmetics.

• Journal of agriculture & life science
• /
• v.46 no.4
• /
• pp.129-139
• /
• 2012

This study was carried out to evaluate the chemical properties and functional characteristics, such as general composition and bioactivity compounds contents of fresh and blanched (at $95^{\circ}C$, for 5min) garlic shoot from Namhae. Also, evaluated antioxidant and antimicrobial activities of water and ethanol extract of fresh and blanched garlic shoot. The moisture content of fresh garlic steam was $ 85.14{\pm}0.35%$, crude protein and crude lipid were $0.79{\pm}0.26%$ and $2.96{\pm}0.03%$ respectively. Vitamin C content was higher in fresh garlic shoot ($7.07{\pm}0.84mg/100g$) than blanched. Total phenol and total chlorophyll contents were respectively $16.93{\pm}1.17mM/g$ and $6.70{\pm}0.46mg/g$ in fresh garlic shoot. Allicin content of blanched garlic shoot was $128.63{\pm}1.59mM/g$. This content was 1.82 times higher than the fresh garlic shoot. Total pyruvate content was higher in fresh garlic shoot ($24.63{\pm}1.59mM/g$), but thiosulfinate was higher in fresh garlic shoot. Total flavonoide was the highest in water extract of blanched garlic shoot ($3.67{\pm}0.00mM/g$). ABTS radical scavenging activity of water extract form blanched garlic shoot was $85.09{\pm}0.28%$, which was higher than the other extracts. NO radical scavenging activity of ethanol extract from blanched garlic shoot was significantly higher than the extracts from fresh garlic shoot. Antibacterial activity to S. aureus, S. enterica, B. cereus and E. coli was only indicated in water extract of fresh garlic shoot.

• Journal of the Korean Wood Science and Technology
• /
• v.13 no.1
• /
• pp.19-62
• /
• 1985

This study was performed to investigate: (i) the bending processing properties of silk worm oak (Quercus acutissima Carr.) and Korean red pine (Pinus densiflora S. et Z.) by boiling and steaming treatments; (ii) the effects of interrelated factors - sapwood and heartwood, annual ring placement, softening temperature and time, moisture content. and wood defects on bending processing properties; (iii) the changing rates of bending radii after release from a tension strap, and (iv) the improving methods of bending process by treatment with chemicals. The size of specimens tested was $15{\times}15{\times}350mm$ for boiling and steaming treatments and $5{\times}10{\times}200mm$ for treatments with chemicals. The specimens were green for boiling treatments and dried to 15 percent for steaming treatments. The specimens for treatments with chemicals were soaked in saturated urea solution, 35 percent formaldehyde solution, 25 percent polyethylene glycol -400 solution, and 25 percent ammonium hydroxide solution for 5 days and immediately followed the bending process, respectively. The results obtained were as follows: 1. The internal temperature of silk worm oak and Korean red pine by boiling and steaming time was raised slowly to $30^{\circ}C$ but rapidly from $30^{\circ}C$ to $80-90^{\circ}C$ and then slowly from $80-90^{\circ}C$ to $100^{\circ}C$. 2. The softening time required to the final temperature was directly proportional to the thickness of specimen. The time required from $25^{\circ}C$ to $100^{\circ}C$ for 15mm-squared specimen was 9.6-11.2 minutes in silk worm oak and 7.6-8.1 minutes in Korean red pine. 3. The moisture content (M.C.) of specimen by steaming time was increased rapidly first 4 minutes in the both species, and moderately from 4 to 20 minutes and then slowly and constantly in silk worm oak, and moderately from 4 to 15 minutes and then slowly and constantly in Korean red pine. The M.C. of 15mm-squared specimen in 50 minutes of steaming was increased to 18.0 percent in the oak and 22.4 percent in the pine from the initial conditioned M.C. of 15 percent The rate of moisture adsorption measured was therefore faster in the pine than in the oak. 4. The mechanical properties of the both species were decreased significantly with the increase of boiling rime. The decrement by the boiling treatment for 60 minutes was measured to 36.6-45.0 percent in compressive strength, 12.5-17.5 percent in tensile strength, 31.6-40.9 percent in modulus of rupture, and 23.3-34.6 percent in modulus of elasticity. 5. The minimum bending radius (M.B.R.) of sapwood and heartwood was 60-80 mm and 90 mm in silk worm oak, and 260 - 300 mm and 280 - 300 mm in Korean red pine, respectively. Therefore, the both species showed better bending processing properties in sapwood than in heartwood. 6. The M.B.R. of edge-grained and flat-grained specimen in suk worm oak was 60-80 mm, but the M.B.R. in Korean red pine was 240-280 mm and 260-360 mm, respectively. Comparing the M.B.R. of edge-grained with flat-grained specimen, in the pine the edge-grained showed better bending processing property than the flat-grained. 7. The bending processing properties of the both species were improved by the rising of softening temperature from $40^{\circ}C$ to $100^{\circ}C$. The minimum softening temperature for bending was $90^{\circ}C$ in silk worm oak and $80^{\circ}C$ in Korean red pine, and the dependency of softening temperature for bending was therefore higher in the oak than in the pine. 8. The bending processing properties of the both species were improved by the increase of softening time as well as temperature, but even after the internal temperature of specimen reaching to the final temperature, somewhat prolonged softening was required to obtain the best plastic conditions. The minimum softening time for bending of 15 mm-squared silk worm oak and Korean red pine specimen was 15 and 10 minutes in the boiling treatment, and 30 and 20 minutes in the steaming treatment, respectively. 9. The optimum M.C. for bending of silk worm oak was 20 percent, and the M.C. above fiber saturation point rather degraded the bending processing property, whereas the optimum M.C. of Korean red pine needed to be above 30 percent. 10. The bending works in the optimum conditions obtained as seen in Table 24 showed that the M.B.R. of silk worm oak and Korean red pine was 80 mm and 240 mm in the boiling treatment, and 50 mm and 280 mm in the steaming treatment, respectively. Therefore, the bending processing property of the oak was better in the steaming than in the boiling treatment, but that of the pine better in the boiling than in the steaming treatment. 11. In the bending without a tension strap, the radio r/t of the minimum bending radius t to the thickness t of silk worm oak and Korean red pine specimen amounted to 16.0 and 21.3 in the boiling treatment, and 17.3 and 24.0 in the steaming treatment, respectively. But in the bending with a tension strap, the r/t of the oak and the pine specimen decreased to 5.3 and 16.0 in t he boiling treatment, and 3.3 and 18.7 in the steaming treatment, respectively. Therefore, the bending processing properties of the both species were significantly improved by the strap. 12. The effect of pin knot on the degradation of bending processing property was very severe in silk worm oak by side, e.g. 90 percent of the oak specimens with pin knot on the concave side were ruptured when bent to a 100 mm radius but only 10 percent of the other specimens with pin knot on the convex side were ruptured. 13. The changing rate in the bending radius of specimen bent to a 300 mm radius after 30 days of exposure to room temperature conditions was measured to 4.0-10.3 percent in the boiling treatment and 13,0-15.0 percent in the steaming treatment. Therefore, the degree of spring back after release was higher in the steaming than in the boiling treatment. And the changing rate of moisture-proofing treated specimen by expoxy resin coating was only -1.0.0 percent. 14. Formaldehyde, 35 percent solution, and 25 percent polyethylene glycol-400 solution found no effect on the plasticization of the both species, but saturated urea solution and 25 percent ammonium hydroxide solution found significant effect in comparison to non-treated specimen. But the effect of the treatment with chemicals alone was inferior to that of the steaming treatment, and the steaming treatment after the treatment with chemicals improved 10-24 percent over the bending processing property of steam-bent specimen. 15. Three plasticity coefficients - load-strain coefficient, strain coefficient, and energy coefficient - were evaluated to be appropriate for the index of bending processing property because the coefficients had highly significant correlation with the bending radius. The fitness of the coefficients as the index was good at load-strain coefficient, energy coefficient, and strain coefficient, in order.