• Composites Research
• /
• v.23 no.2
• /
• pp.24-30
• /
• 2010

Interfacial evaluation and hydrophobicity of Ni-nanopowder/epoxy composites were investigated for self-sensing and actuation. Contact resistance and resistivity were measured using gradient micro-specimens. The actuation of the composites in the electromagnetic field was studied with three wave functions, i.e., sine, triangle and square functions. Due tothe presence of hydrophobic domains on the heterogeneous surface, the static contact angle of Ni-nanopowder/epoxy nanocomposite wasabout $100^{\circ}$, which was rather lower than that for super-hydrophobicity. The dynamic contact angle showed the similar trend of static contact angle. Ni-nanopowder/epoxy composite was responded wellfor both self-sensing and actuation in electromagnetic field due to the intrinsic metal property of Ni-nanopowder. Displacement of the actuator of Ni-nanopowder/epoxy composite was evaluated to obtain the maximum and the optimum performance using laser displacement sensor as functions of the wave type, frequency, and voltage. Actuation of Ni-nanopowder/epoxy composites also increased as functions of applied frequency and voltage. Actuated strain increased more rapidly at sine wave with increasing voltage compared to those of triangle or rectangular waves.

• Journal of Sensor Science and Technology
• /
• v.29 no.4
• /
• pp.266-269
• /
• 2020

In this study, we investigated the effect of a sulfur passivation (S-passivation) process step on the electrical properties of surface-channel In_0.7Ga_0.3As quantum-well (QW) metal-oxide-semiconductor field-effect transistors (MOSFETs) with S/D regrowth contacts. We fabricated long-channel In_0.7Ga_0.3As QW MOSFETs with and without (NH₄)₂S treatment and then deposited 1/4 nm of Al₂O₃/HfO₂ through atomic layer deposition. The devices with S-passivation exhibited lower values of subthreshold swing (74 mV/decade) and drain-induced barrier lowering (19 mV/V) than the devices without S-passivation. A conductance method was applied, and a low value of interface trap density D_it (2.83×10¹² cm^-2eV^-1) was obtained for the devices with S-passivation. Based on these results, interface traps between InGaAs and high-κ are other defect sources that need to be considered in future studies to improve III-V microsensor sensing platforms.

• Journal of Institute of Control, Robotics and Systems
• /
• v.3 no.6
• /
• pp.644-651
• /
• 1997

In the water purification plant, chemicals are injected for quick purification of raw water. It is clear that the amount of chemicals intrinsically depends on water quality such as turbidity, temperature, pH and alkalinity. However, the process of chemical reaction to improve water quality (e.g., turbidity) by chemicals is not yet fully clarified nor quantified. The feedback signal in the process of coagulant dosage, which should be measured (through the sensor of the plant) to compute the appropriate amount of chemicals, is also not available. Most traditional methods focus on judging the conditions of purifying reaction and determine the amounts of chemicals through manual operation of field experts using Jar-test data. In this paper, a systematic control strategy is proposed to derive the optimum dosage of coagulant, PAC(Polymerized Aluminium Chloride), using Jar-test results. A neural network model is developed for coagulant dosing and purifying process by means of six input variables (turbidity, temperature, pH, alkalinity of raw water, PAC feed rate, turbidity in flocculation) and one output variable, while considering the relationships to the reaction of coagulation and flocculation. The model is utilized to derive the optimum coagulant dosage (in the sense of minimizing turbidity of water in flocculator). The ability of the proposed control scheme validated through the field test has proved to be of considerable practical value.

• Journal of Environmental Science International
• /
• v.17 no.1
• /
• pp.85-95
• /
• 2008

Temporal and spatial variabilities of chlorophyll a (Chl-a) in the northern East China Sea (ECS) are described, using both 8-day composite images of the SeaWiFS (Sea-viewing Wide Field-of-view Sensor) and in-situ data investigated in August and September during 2000-2005. Ocean color imagery showed that Chl-a concentrations on the continental shelf within the 50 m depth in the ECS were above 10 times higher than those of the Kuroshio area throughout the year. Higher concentrations (above $5mg/m^3$) of yearly mean Chl-a were observed along the western part of the shelf near the coast of China. The standard deviation also showed the characteristics of the spatial variability near $122-124^{\circ}E$, where the western region of the East China Sea was grater than that of the eastern region. Particularly the significant concentration of Chl-a, up to $9mg/m^3$, was found at the western part of $125^{\circ}E$ in the in-situ data of 2002. The higher Chl-a concentrations of in-situ data were consistent with low salinity waters of below 30 psu. It means that there were the close relationship between the horizontal distribution of Chl-a and low salinity water.

• Journal of Sensor Science and Technology
• /
• v.4 no.4
• /
• pp.75-80
• /
• 1995

In order to fabricate the piezoelectric thin film of the PZT-PNN ternary compound, the metal alkoxides were used as starting materials. The electrical and crystalline properties of the thin film were evaluated. The X- RD study shows that the crystallization of the film is optimized at $550^{\circ}C$ of sintering temperature. According to the D-E hysterisis curve, the coercive field is 28.8 kV /cm, and the remanent polariztion is $18.3\;{\mu}C/cm^{2}$. The break down voltages of the thin films are $76.0\;{\sim}\;27.0\;MV/m$. When the sintering temperature is raised, the break down voltage is lowered. As a result of measuring the C-V characteristic curve of the ternary compound piezoelectric thin film, the relative dielectric constants are 406 for the composition (50:40:10), 1084 for the composition (50:30:20), 723 for the composition (45:35:20) and 316 for the composition (40:40:20).

• Journal of Sensor Science and Technology
• /
• v.4 no.2
• /
• pp.58-63
• /
• 1995

The effects of substrate temperature, RF power, and $NH_{3}/SiH_{4}$ gas flow ratio on the dielectric constant and optical bandgap of amorphous silicon nitride (a-SiNx:H) thin films prepared by PECVD method using RF glow discharge decomposition of $SiH_{4}$ and $NH_{3}$ gas mixtures have been studied. The dielectric constant and optical bandgap of a-SiNx:H thin films were greatly exchanged as by increasing substrate temperature, RF power, and $NH_{3}/SiH_{4}$ gas flow ratio. The dielectric constant of a-SiNx:H films was increased and optical bandgap of a-SiNx:H films was decreased as the substrate temperature was increased. When the substrate temperature, RF power, gas pressure, $NH_{3}/SiH_{4}$ gas flow ratio, and thickness were $250^{\circ}C$, 20 W, 500 mTorr, 10 and $1500\;{\AA}$, respectively, the dielectric constant, breakdown field and optical bandgap of a-SiNx:H film were 4.3, 1 MV/cm, and 2.9 eV, respectively.

• Korean Journal of Agricultural and Forest Meteorology
• /
• v.24 no.1
• /
• pp.13-34
• /
• 2022

Soil moisture data have been collected at 11 agrometeorological stations operated by The Korea Meteorological Administration (KMA). This study aimed to verify the accuracy of soil moisture data of KMA and develop a correction formula to be applied to improve their quality. The soil of the observation field was sampled to analyze its physical properties that affect soil water content. Soil texture was classified to be sandy loam and loamy sand at most sites. The bulk density of the soil samples was about 1.5 g/cm³ on average. The content of silt and clay was also closely related to bulk density and water holding capacity. The EnviroSCAN model, which was used as a reference sensor, was calibrated using the self-manufactured "reference soil moisture observation system". Comparison between the calibrated reference sensor and the field sensor of KMA was conducted at least three times at each of the 11 sites. Overall, the trend of fluctuations over time in the measured values of the two sensors appeared similar. Still, there were sites where the latter had relatively lower soil moisture values than the former. A linear correction formula was derived for each site and depth using the range and average of the observed data for the given period. This correction formula resulted in an improvement in agreement between sensor values at the Suwon site. In addition, the detailed approach was developed to estimate the correction value for the period in which a correction formula was not calculated. In summary, the correction of soil moisture data at a regular time interval, e.g., twice a year, would be recommended for all observation sites to improve the quality of soil moisture observation data.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.6
• /
• pp.472-482
• /
• 2019

This paper describes the stabilization of underwater TAS winch system Deploy/Recover operation performance. TAS winch installed on the stern of submarine performs to deploy/recover sensor, towing cable and rope tail which is deployed from the stern and separated from submarine itself. Also TAS winch provides transmission path of power to the sensor and data transmitting/receiving path which data are acquired from underwater environment like sound, depth and temperature. At the step of TAS winch evaluation test, sporadic standstill and rotating speed oscillation phenomenon were occurred. Winch motor provides the available torque to deploy/recover TAS and root cause analysis to the winch motor was done to find exact reason to sporadic malfunction. When winch motor was disassembled, eccentricity of rotor, slip-ring and the other composition part for winch motor were found. These might cause magnetic field distortion. To make TAS winch system more stable and block magnetic field distortion, this paper suggests methods to enhance fixing status installed in winch motor. For reliable data acquisition for TAS winch operation, the deploy/recover function of the improved type of TAS winch was verified in LBTS making similar condition with sea status. At the end of stage, improved type of TAS winch was tested on some functions not only deploy/recover function, but sustainability of TAS operation on specific velocity, steering angle of submarine in the sea trial. Improved type of TAS winch was verified in accordance with design requirement. Also, validity of suggested methods were verified by the sea trial.

• Korean Journal of Remote Sensing
• /
• v.16 no.3
• /
• pp.211-220
• /
• 2000

Even though recurring eddies at the terminal end of the East Korean Warm Current have been identified in the thermal infrared imagery from the NOAA/AVHRR sensor and ocean color data from Orbview-2/SeaWiFS sensor, it is difficult to make observation in the field regarding recurring eddies located around the Wonsan coastal area in North Korea. But we could get in situ data related to an eddy from an ARGOS satellite tracking drifter trapped in the eddy on January 4th, 1999. An ARGOS drifter, a NOAA satellite tracked buoy was trapped by the eddy during January 4th.March 18, 1999. The ARGOS drifter rotated 10 times per 72 days on the edge of the eddy located at $39^{\circ}N$, $129^{\circ}E$. The diameter of the eddy was about 100 km. The horizontal rotation velocity of the recurring cold-core anti-cyclonic eddy was 1.53 km/h(42 cm/sec). The sea surface temperatures of the eddy varied from $14.7^{\circ}C$ on January 5, 1999 to $9.6^{\circ}C$ on March 18,1999. To study the mechanism of the recurring eddy. we tried to find out the relationship between the vector of the drifter moving in the eddy and the wind vector in Sokcho and Ulleung Island located near the eddy in southern Korea, and the difference in sea level between Ulleung Island and Mukho. We hope the results of this study would be useful for calibration and validation data of simulation and numerical modeling studies of the recurring eddy.

• Korean Journal of Optics and Photonics
• /
• v.17 no.5
• /
• pp.383-390
• /
• 2006

The SharkHartmann wavefront sensors are the most popular devices to measure wavefront in the field of adaptive optics. The Shack-Hartmann sensors measure the centroids of spot irradiance distribution formed by each corresponding micro-lens. The centroids are linearly proportional to the local mean slopes of the wavefront defined within the corresponding sub-aperture. The wavefront is then reconstructed from the evaluated local mean slopes. The uncertainty of the Shack-Hartmann sensor is caused by various factors including the detector noise, the limited size of the detector, the magnitude and profile of spot irradiance distribution, etc. This paper investigates the noise propagation in two major centroid evaluation algorithms through computer simulation; 1st order moments of the irradiance algorithms i.e. center of gravity algorithm, and correlation algorithm. First, the center of gravity algorithm is shown to have relatively large dependence on the magnitudes of noises and the shape & size of irradiance sidelobes, whose effects are also shown to be minimized by optimal thresholding. Second, the correlation algorithm is shown to be robust over those effects, while its measurement accuracy is vulnerable to the size variation of the reference spot. The investigation is finally confirmed by experimental measurements of defocus wavefront aberrations using a Shack-Hartmann sensor using those two algorithms.