• Journal of Sensor Science and Technology
• /
• v.6 no.2
• /
• pp.137-144
• /
• 1997

In this paper, the design of a 10-bit 40-MS/s pipelined A/D converter is implemented to achieve low static power dissipation of 70 mW at the ${\pm}2.5\;V$ or +5 V power supply environment for high speed applications. A 1.5 b/stage pipeline architecture in the proposed ADC is used to allow large correction range for comparator offset and perform the fast interstage signal processing. According to necessity of high-performance op amps for design of the ADC, the new op amp with gain boosting based on a typical folded-cascode architecture is designed by using SAPICE that is an automatic design tool of op amps based on circuit simulation. A dynamic comparator with a capacitive reference voltage divider that consumes nearly no static power for this low power ADC was adopted. The ADC implemented using a $1.0{\mu}m$ n-well CMOS technology exhibits a DNL of ${\pm}0.6$ LSB, INL of +1/-0.75 LSB and SNDR of 56.3 dB for 9.97 MHz input while sampling at 40 MHz.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.53 no.7
• /
• pp.39-46
• /
• 2016

This paper describes the third order feedforward delta-sigma modulator with inverter-based integrators and a 1.5bit comparator for the application of audio signal processing. The proposed 3rd-order delta-sigma modulator is multi-bit structure using 1.5 bit comparator instead of operational amplifier. This delta-sigma modulator has high SNR compared with single-bit 4th-order delta-sigma modulator in a low OSR. And it minimizes power consumes and simplified circuit structure using inverter-based integrator and using inverter-based integrator as analogue adder. The modulator was designed with 0.18um CMOS standard process and total chip area is $0.36mm^2$. The measured power cosumption is 28.8uW in a 0.8V analog supply and 66.6uW in a 1.8V digital supply. The measurement result shows that the peak SNDR of 80.7 dB, the ENOB of 13.1bit and the dynamic range of 86.1 dB with an input signal frequency of 2.5kHz, a sampling frequency of 2.56MHz and an oversampling rate of 64. The FOM (Walden) from the measurement result is 269 fJ/step, FOM (Schreier) was calculated as 169.3 dB.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.16 no.9
• /
• pp.1847-1855
• /
• 2012

A 1V 1.6-GS/s 6-bit flash analog-to-digital converter (ADC) with a clock calibration circuit is proposed. A single track/hold circuit with a bootstrapped analog switch is used as an input stage with a supply voltage of 1V for the high speed operation. Two preamplifier-arrays and each comparator composed of two-stage are implemented for the reduction of analog noises and high speed operation. The clock calibration circuit in the proposed flash ADC improves the dynamic performance of the entire flash ADC by optimizing the duty cycle and phase of the clock. It adjusts the reset and evaluation time of the clock for the comparator by controlling the duty cycle of the clock. The proposed 1.6-GS/s 6-bit flash ADC is fabricated in a 1V 90nm 1-poly 9-metal CMOS process. The measured SNDR is 32.8 dB for a 800 MHz analog input signal. The measured DNL and INL are +0.38/-0.37 LSB, +0.64/-0.64 LSB, respectively. The power consumption and chip area are $800{\times}500{\mu}m2$ and 193.02mW.

• Journal of IKEEE
• /
• v.11 no.1 s.20
• /
• pp.38-45
• /
• 2007

A new 8-bit single-slope ADC using analog RAMP generator with digitally controllable dynamic range has been proposed and simulated for column level or per-pixel CMOS image sensor application. The conversion gain of ADC can he controlled easily by using frequency divider with digitally controllable diviber ratio, coarse/fine RAMP with class-AB op-amp, resistor strings, decoder, comparator, and etc. The chip area and power consumption can be decreased by simplified analog circuits and passive components. Proposed frequency divider has been implemented and verified with 0.65um, 2-poly, 2-metal standard CMOS process. And the functional verification has been simulated and accomplished in a 0.35$\mu$m standard CMOS process.

• Proceedings of the IEEK Conference
• /
• 2001.06b
• /
• pp.253-256
• /
• 2001

This paper introduces the design of high-speed analog- to-digital converter for high-definition TV, camcorders, portable equipments and implemented in a 0.65${\mu}{\textrm}{m}$ CMOS technology. Key circuits developed for low power and high speed A/D converter are a dynamic comparator that consumes no static power, a source follower buffered op amp that achives wide bandwidth using large input devices. The converter achieves low power dissipation of 40-mW at 3.3-V power supply. Measured performance includes 0.53 LSB of INL and 0.48 LSB of DNL while sampling at 60MHz.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.14 no.6
• /
• pp.706-711
• /
• 2014

A low power 6-bit flash ADC that uses an input voltage range detection algorithm is described. An input voltage level detector circuit has been designed to overcome the disadvantages of the flash ADC which consume most of the dynamic power dissipation due to comparators array. In this work, four digital input voltage range detectors are employed and each input voltage range detector generates the specific clock signal only if the input voltage falls between two adjacent reference voltages applied to the detector. The specific clock signal generated by the detector is applied to turn the corresponding latched comparators on and the rest of the comparators off. This ADC consumes 68.82 mW with a single power supply of 1.2V and achieves 4.3 effective number of bits for input frequency up to 1 MHz at 500 MS/s. Therefore it results in 4.6 pJ/step of Figure of Merit (FoM). The chip is fabricated in 0.13-um CMOS process.

• The KIPS Transactions:PartA
• /
• v.14A no.2
• /
• pp.117-124
• /
• 2007

In this paper we present a translation lookaside buffer (TLB) system with low power consumption for embedded processors. The proposed TLB is constructed as multiple banks, each with an associated block buffer and a corresponding comparator. Either the block buffer or the main bank is selectively accessed on the basis of two bits in the block buffer (tag buffer). Dynamic power savings are achieved by reducing the number of entries accessed in parallel, as a result of using the tag buffer as a filtering mechanism. The performance overhead of the proposed TLB is negligible compared with other hierarchical TLB structures. For example, the two-cycle overhead of the proposed TLB is only about 1%, as compared with 5% overhead for a filter (micro) TLB and 14% overhead for a same structure without continuos accessing distinction algorithm. We show that the average hit ratios of the block buffers and the main banks of the proposed TLB are 95% and 5% respectively. Dynamic power is reduced by about 95% with respect to with a fully associative TLB, 90% with respect to a filter TLB, and 40% relative to a same structure without continuos accessing distinction algorithm.

• Journal of IKEEE
• /
• v.14 no.2
• /
• pp.90-97
• /
• 2010

The high efficiency power management IC(PMIC) with DTMOS(Dynamic Threshold voltage MOSFET) switching device and DTMOS Error Amplifier is presented in this paper. PMIC is controlled with PWM control method in order to have high power efficiency at high current level. Dynamic Threshold voltage CMOS(DT-CMOS) with low on-resistance is designed to decrease conduction loss. The control parts in Buck converter, that is, PWM control circuits consist of a saw-tooth generator, a band-gap reference circuit, an DT-CMOS error amplifier and a comparator circuit as a block. the proposed DT-CMOS Error Amplifier has 72dB DC gain and 83.5deg phase margin. also Error Amplifier that use DTMOS more than CMOS showed power consumption decrease of about 30%. DC-DC converter, based on Voltage-mode PWM control circuits and low on-resistance switching device is achieved the high efficiency near 96% at 100mA output current. And DC-DC converter is designed with Low Drop Out regulator(LDO regulator) in stand-by mode which fewer than 1mA for high efficiency.

• The Transactions of the Korea Information Processing Society
• /
• v.4 no.8
• /
• pp.2120-2132
• /
• 1997

A layout automation system for analog integrated circuits is proposed. The implemented system performs full-custom analog layout under the analog layout constraints. In order to overcome the demerits of conventional analog layout systems, parameterized module library is proposed. The system can support complex analog layout modules, resulting in a maximum expandability of the system. Moreover, modified dynamic multi-path algorithm is developed by enhancing the conventional Dijkstra algorithm. Several benchmark circuits such as comparator, op amp, and filter was tested by the system. Layout results compared to OPASYN show well-merging layout and interdigitized layout module.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.13 no.1
• /
• pp.8-16
• /
• 2020

In this paper, a single-bit 2nd-order delta-sigma modulator with the architecture of cascaded-of-integrator feedforward (CIFF) is proposed for column-parallel analog-to-digital converter (ADC) array used in a low noise CMOS image sensor. The proposed modulator implements two switched capacitor integrators and a single-bit comparator within only 10-㎛ column-pitch for column-parallel ADC array. Also, peripheral circuits for driving all column modulators include a non-overlapping clock generator and a bias circuit. The proposed delta-sigma modulator has been implemented in a 110-nm CMOS process. It achieves 88.1-dB signal-to-noise-and-distortion ratio (SNDR), 88.6-dB spurious-free dynamic range (SFDR), and 14.3-bit effective-number-of-bits (ENOB) with an oversampling ratio (OSR) of 418 for 12-kHz bandwidth. The area and power consumption of the delta-sigma modulator are 970×10 ㎛2 and 248 ㎼, respectively.