• 소성∙가공
• /
• 제10권7호
• /
• pp.573-578
• /
• 2001

The flow stress of 304 stainless steel during hot forming process were determined by conducting hot compression tests at the range of 1273 K∼1423 K and 0.05 /s∼2.0 /s as these are typical temperature and strain rate in hot forging operation. In this material, Dynamic recrystallization was found to be the major softening mechanism with this conditions as Previous studies. Based on the observed phenomena, a constitutive model of flow stress was assumed as a function of strain, strain rate, temperature. In the constitutive model, the effects of strain hardening and dynamic recrystallization were taken into consideration. A finite element method connected to constitutive model was performed to predict the dynamic recrystallization behaviors and also stress-strain curves in hot compression of 304 stainless steel.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2006년도 춘계학술대회 논문집
• /
• pp.59-62
• /
• 2006

Mg alloys have drawn a huge attention in the field of transportation and consumer electronics industries since it is the lightest alloy which could be industrially applicable. Most Mg alloy components have been fabricated by casting method. However, there have been a lot of research activities on the wrought alloys and their plastic forming process recently. The deformation behavior of an AZ31 Mg alloy at the elevated temperature was examined firstly to find out the optimum plastic forming range in terms of temperature and strain rate. During high temperature deformation, AZ31 alloy is usually undergone the dynamic recrystallization which influence the deformation behavior in turn. In the present study, the effect of deformation on dynamic recrystallization of an AZ31 alloy was investigated to clarify the relation between the deformation and recrystallization. In an AZ31 alloy system, the dynamic recrystallization was found to occur continuously. Recrystallized grain size was dependent on the stress level.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 1999년도 추계학술발표대회 논문집
• /
• pp.1-4
• /
• 1999

The attenuation coefficients of SiC particle reinforced low-density polyethylene (LDPE) matrix composites were measured by pulse echo method and dynamic elastic measure method with varying the volume fraction of SiC particle ranged from 0% to 40% and the size of SiC particles ranged from 0.8$\mu$m to 48$\mu$m. The SiCp/LDPE composites were fabricated with the melt injection process and the fabricated composites showed almost full density above 99% up to 40vo1% SiCp reinforcements. The attenuation constant of LDPE measured by dynamic elastic constant had same result with that measured by pulse echo method, but the attenuation constant of SiCp/LDPE measured by dynamic elastic constant did not have same result with that measured by pulse echo method.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 추계학술대회 논문집
• /
• pp.812-815
• /
• 1997

A dynamic model of air circuit breaker with a spring-actuated linkage is derived, and its validation for analysis and design, particularly appropriateness for an analysis of high-speed motion behavior are checked through experiments. The dynamic model is developed through the modeling process based on ADAMS and Pro/Engineer. The simulation results of derived dynamic models for the rapid closing and opening operations are compared with actual responses using a high-speed camera and investigated to validate their usefulness.

• 한국정밀공학회지
• /
• 제19권12호
• /
• pp.64-69
• /
• 2002

In this study, the optimal dynamic isolation system for gas operated combat weapon has been investigated. For this purpose, firstly, the dynamic behavior of human induced by firing operations has been analyzed through a series of experimental works using the devised test setup. The characteristics of linear impulse has been compared under some conditions of support system. In order to design the optimal dynamic isolation system, parameter optimization process has been performed based on the simplified isolation system under constraints of moving displacement and transmitted force. Finally, the performance of the designed dynamic absorbing system has been evaluated by simulation.

• 한국정밀공학회지
• /
• 제21권10호
• /
• pp.115-126
• /
• 2004

In the present work a finite element formulation using dynamic-explicit time integration scheme is used for numerical analysis of auto-body panel stamping processes. The lumping scheme is employed for the diagonal mass matrix and dynamic explicit formulation. Analyzed auto-body panel stomping process correction of forming using software called Dynaform using dynamic extensive method. Further, the simulated results for the auto-body panel stamping processes are shown and discussed. Its application is being increased especially in the automotive industrial area for the cost reduction, weight saving, and improvement of strength.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2003년도 춘계학술대회 논문집
• /
• pp.1418-1421
• /
• 2003

The Vacuum circuit breaker is a kind of power circuit breaker and protect electric devices from over-current. In this paper we built a dynamic model of VCB driving mechanism using ADAMS. The development of the new circuit breaker with less energy and more compactable mechanism is focused. Through the dynamic model, the concept design of the new circuit breaker with less energy and more compactable mechanism is proposed, and then the detailed design is carried out through the design process based on the dynamic model.

• 한국생산제조학회지
• /
• 제21권5호
• /
• pp.691-696
• /
• 2012

In this study, a rigid multi-body dynamic model has been developed for mechatronic analysis to evaluate dynamic behavior of a machine tool. The development environment was the commercialized analysis tool, ADAMS, for rigid multi-body dynamic analysis. A simplified servo control logic was implemented in the tool using its functions in order to negate any external tool of control definition. The advantage of the internal implementation includes convenience of the analysis process by saving time and efforts. Application of this development to a machine tool helps to evaluate its dynamic behavior against feeding its component, to calculate the motor torque, and to optimize parameters of the control logic.

• 소음진동
• /
• 제8권1호
• /
• pp.87-98
• /
• 1998

A Precise actuator in the pick-up of a DVDR/P(Digital Video Disk Recorder/Player) is required to control position accurately. Therefore, in order to develop a reliable actuator, dynamic characteristics of each part in an actuator should be examined closely. This paper presents systematic design process of an actuator using various analysis methods to confirm fundamental capability and solve performance problems related to dynamic characteristics of an actuator beforehand. Particularly, sensitivity analysis is presented through the program using mass moment of inertia and general equations of rigid body. Through the result of sensitivity analysis, important inferiority causes of actuator are selected and reduced. In the end, dynamic characteristics of manufactured actuators are improved considerably.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2006년도 정기 학술대회 논문집
• /
• pp.341-346
• /
• 2006

This paper provides the resuIts on the evaluation of dynamic characteristics of the optimized shells. Five fundamental technologies such as computer-aided geometric design, automatic mesh generation, shell finite element, design sensitivity analysis and shell optimization process, are used for shell optimization maximizing the fundamental natural frequency. A dome shell is adopted for the shell shape optimization and the dynamic characteristic of the optimized shell such as the variation of natural frequencies is then investigated. From the investigation, more constraint functions related to shell natural frequencies is necessarily required to effectively control dynamic characteristics of the optimized shells.