• Journal of Power Electronics
• /
• v.14 no.6
• /
• pp.1217-1223
• /
• 2014

A novel half load-cycle worked dual input single output (DISO) DC/AC inverter is presented. The basic circuit consists of a dual buck regulator, which works in continuous current mode. The working principle of DISO DC/AC inverter has been used. The control method applied for half load-cycle worked DISO DC/AC inverter has been studied. The control effects of the open-loop proportional control and closed-loop proportional-integral control are compared by using PSIM software. The parameters are adopted in the realistic simulation and experiment test. Moreover, the waveforms, such as voltage of modulation reference signal and output voltage, were given. The simulation and experiment results proved that the half load-cycle worked DISO DC/AC inverter could achieve good performance, gain a line frequency of 50 Hz, and verify the correctness of theoretical analysis.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.16 no.5 s.110
• /
• pp.479-484
• /
• 2006

This paper presents an active control of the aperture type near-field storage head. In order to achieve a fast and accurate control, a dual servo control algorithm is applied. Based on the big difference in time constants of two actuators, they are used independently. With the combination fine and coarse actuator, the disk is rotated up to 10 rpm speed until the gap is controlled within 100 nm. From the experimental results, the feasibility and the performance of active dual servo gap control is proved.

• Proceedings of the KIPE Conference
• /
• 1998.07a
• /
• pp.405-408
• /
• 1998

In this paper, a predictive current control of 12-pulse parallel connected dual converter system with interphase transfromer(IPT) is presented. Firstly, 12-pulse parallel connected dual converter system and the predictive current control of this system is discussed. And the validity of the presented system and the excellence of the predictive current control response is proved through the simyulation and experiment result.

• Proceedings of the KIEE Conference
• /
• 1994.11a
• /
• pp.83-85
• /
• 1994

This paper describes the dual mode control of the LDM(Linear DC motor) for carrier. The dual mode control consists of seek and analogue control. In seek mode, LDM is moved in the shortest time by switching line, and in analogue mode keeps at origion with high accuracy. We proposed different switching line method according to driving direction.

• Proceedings of the KIEE Conference
• /
• 2001.07d
• /
• pp.2277-2279
• /
• 2001

This paper describes a vision-based steering control method for AGV which use dual motor drive. We suggest an algorithm which can be detect the guideline quickly and exactly for real time vision processing, and control the steering through an assign the CP (Control - Point) of input image. This method is tested via a IAGV which dual motor drive with a single camera in laboratory environment.

• Journal of Institute of Control, Robotics and Systems
• /
• v.9 no.4
• /
• pp.277-283
• /
• 2003

Recently, near-field recording (NFR) disk drive schemes have been proposed with a view to increasing recording densities of hard disk drives. Compared with hard disk drives. NFR disk drives have narrower track pitches and are exposed to more severe periodic disturbances resulting from eccentric rotation of the disk. It is difficult to meet servo system design specifications for NFR disk drives with conventional VCM actuators in that the servo system for an NFR disk drive generally requires a feater gain and higher bandwidth. To tackle the problem various dual-stage actuator systems composed of a microactuator mounted on top of a conventional VCM actuator have been proposed. This article deals with the problem of designing a tracking servo system far an NFR disk drive adopting a dual-stage actuator. We summarize design constraints pertaining to the dual-stage servo system and present a new servo scheme using iterative teaming control. We design feedback compensators and an iterative teaming controller for a target plant and verify the validity of the proposed control scheme through a computer simulation.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.11 no.11
• /
• pp.5338-5359
• /
• 2017

In-band full-duplex (IBFD) wireless communication supports symmetric dual transmission between two nodes and asymmetric dual transmission among three nodes, which allows improved throughput for distributed IBFD wireless networks. However, inter-node interference (INI) can affect desired packet reception in the downlink of three-node topology. The current Half-duplex (HD) medium access control (MAC) mechanism RTS/CTS is unable to establish an asymmetric dual link and consequently to suppress INI. In this paper, we propose a medium access control mechanism for use in distributed IBFD wireless networks, FD-DMAC (Full-Duplex Distributed MAC). In this approach, communication nodes only require single channel access to establish symmetric or asymmetric dual link, and we fully consider the two transmission modes of asymmetric dual link. Through FD-DMAC medium access, the neighbors of communication nodes can clearly know network transmission status, which will provide other opportunities of asymmetric IBFD dual communication and solve hidden node problem. Additionally, we leverage FD-DMAC to transmit received power information. This approach can assist communication nodes to adjust transmit powers and suppress INI. Finally, we give a theoretical analysis of network performance using a discrete-time Markov model. The numerical results show that FD-DMAC achieves a significant improvement over RTS/CTS in terms of throughput and delay.

• Journal of Electrical Engineering and Technology
• /
• v.12 no.2
• /
• pp.674-682
• /
• 2017

This paper presents an optimal initial firing angle control based on the energy consumption and regenerative energy of a parallel multi-pulse thyristor dual converter for urban railway power substations. To prevent short circuiting the thyristor dual converter, a hysteresis band for maintaining a zero-current discontinuous section (ZCDS) is essential during mode changes. During conversion from the ZCDS to forward or reverse mode, the DC trolley voltage can be stabilized by selecting the optimal initial firing angle without an overshoot and slow response. However, the optimal initial firing angle is different depending on the line impedance of each converter. Therefore, the control algorithm for tracking the optimal initial firing angle is proposed to eliminate the overshoot and slow response of DC trolley voltage. Simulations and experiments show that the proposed algorithm yields the fastest DC voltage control performance in the transient state by tracking the optimal firing angle.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.664-669
• /
• 2003

This paper proposes a swing-arm type dual-stage actuator, which consists of a PZT actuator for fine motion and a VCM(Voice Coil Motor) for coarse motion, for SFF ODD(Small Form Factor Optical Disk Drive), in order to achieve fast access speed and precise track following control. We focus our attention on the design and control of the PZT actuator, because there have been a lot of previous researches related to the VCM and dual-stage actuators. Due to the dual cantilever structure, the PZT actuator can generate precise translational tracking motion at its tip where optical pickup is attached at, and the effect of hysteric behavior of the PZT element is reduced. The dynamic model of the PZT actuator is derived by using the Hamilton's principle, and verified by comparing with the experimental frequency response. The sliding mode control is designed in order to be robust against modeling uncertainties. Simulations and experimental results confirm the effectiveness of the suggested control scheme.

• 제어로봇시스템학회:학술대회논문집
• /
• 1990.10b
• /
• pp.1156-1161
• /
• 1990

The concept of the manipulability measure of the robotic mechanism is extended to the dual arm holding a single object. This is a measure of manipulating ability of the dual arm forming a closed kinematic chain in positioning and orienting the object. Dual arm manipulability measure is defined and compared to the single arm manipulability measure, and some properties are investigated.