• Transactions of the KSME C: Technology and Education
• /
• v.3 no.1
• /
• pp.23-28
• /
• 2015

In this paper, we performed the design optimization dual-shell and tube heat exchanger on exhaust waste heat recovery for gas heat pump using CFD and RSM. CFD analysis is useful to design the complex structure such as double shell and tube heat exchanger. By computer simulation, engineers can assess the feasibility of the given design factors and change them to get a better design. But if one wishes to perform complex analysis on the simulation, such dual-shell and tube heat exchanger for GHP, the computational time can become overwhelming. CFD is powerful but it takes a lot of time for complex structure. Therefore, the CFD analysis is minimized by the optimization using the RSM method. As a result, the number of baffle and tube are optimized by 6 baffles and 25 tubes for heat transfer and flow friction. And then pressure drop and heat transfer is improved about 12.2%. We confirm the design optimization using CFD and RSM is useful on complex structure of heat exchanger.

• Korean Journal of Microbiology
• /
• v.42 no.3
• /
• pp.223-229
• /
• 2006

To develop multifunctional microbial inoculant, an insluble phosphate-solubilizing bacterium with antifungal activity was isolated from plant rhizospheric soil. On the basis of its morphological, cultural and physiological characteristics and Biolog analysis, this bacterium was identified as Pseudomonas fluorescens RAF15. P. fluorescens RAF15 showed antifungal activities against phytopathogenic fungi Botrytis cinerea and Rhizoctonia solani. The optimal medium composition and cultural conditions for the solubilization of insoluble phosphate by P. fluorescens RAF15 were 1.5% of glucose, 0.005% of urea, 0.3% $MgCl_2{\cdot}6H_2\;0.01%\;of\;MgSO_4{\cdot}7H_2O\;0.01%,\;of\;CaCl_2{\cdot}2H_2O$, and 0.05% of NaCl along with initial pH 7.0 at $30^{\circ}C$. The soluble phosphate production under optimum condition was 863 mg/L after 5 days of cultivation. The solubilization of insoluble phosphates was associated with a drop in the pH of the culture medium. P. fluorescens RAF15 showed resistance against different environmental stresses like $10-35^{\circ}C$ temperature, 1-4% salt concentration and pH 2-11 range. The strain produced soluble phosphate to the culture broth with the concentrations of 971-1121 mg/L against $CaHPO_4$, 791-908 mg/L against $Ca_3(PO_4){_2}$, and 844 mg/L against hydroxyapatite, respectively. However, the strain produced soluble phosphate to the culture broth with the concentrations of 15 mg/L against $FePO_4$, and 5 mg/L against $AlPO_4$, respectively.

• KSBB Journal
• /
• v.19 no.6 s.89
• /
• pp.446-450
• /
• 2004

We investigated the effective culture conditions of anaerobic bacteria, Enterobacter cloacae YJ-1 on hydrogen production. It was cultured with 60 mL of working volume at $35^{\circ}C$, 120 rpm for 40 h. With culture time, hydrogen production and cell growth increased, but residual glucose and pH decreased. When the $2\%$ of glucose was used as single carbon source, hydrogen production was 975.1 mL/L. To enhance hydrogen productivity, mixed carbon sources of glucose and sucrose were added. The maximum hydrogen production was earned at the mixing ratio of 25:75, and it was 1319.5 mL/L. When we added 50 mM of phosphate to protect the pH drop in culture broth, hydrogen production increased 1.3 times more than that of initial concentration. The organic nitrogen sources were more effective than inorganic nitrogen for hydrogen production. Among organic nitrogen, yeast extract was the most effective and its hydrogen production was 1691.3 mL/L. Among 9 of mineral sources, Ferric citrate and $NaMoO_4$ were especially effective, and their productions were 1782.3 mL/L and 1784.8 mL/L, respectively.

• Journal of Technologic Dentistry
• /
• v.34 no.3
• /
• pp.263-271
• /
• 2012

Purpose: The purpose of this research was to examine department satisfaction for improving the competitiveness of department of dental technology and providing basic data for students successful guidance. Methods: The study subject were 560 students from 4 colleges, and they were selected by the convenient sampling method. Data for this survey was obtain by self-administration method. This questionnaire consist of general characteristics, the awareness of before entering department of dental technology, the satisfaction of department of dental technology, an opinion about change of one's course and temporary absence. Results: About the time of selecting their major, 70.1% of students answered the most before highschool. Department of dental technology and the most common source of information in selecting a majors is the person oneself(52.6%). The person who answers because of knowing a little bit for the question asking the priori knowledge of department of dental technology showed up as 66.3%. About the motivation for selection their major, 37.4% of students answered the most it seemed to be a future prospect. As to the extend of department satisfaction, the satisfaction showed up as 63.3%, but the extend of satisfaction was exposed to reduce as the grade increased. The dissatisfaction factor is the difficulty of the theory(29.8%). Many students do not want to change their majors even if they are provided with the chance to do so(68.7%). From the survey related to the experience of thinking over temporary absence and drop out, 56.8% of students responded they had experienced thinking about that. Current feelings after department selection was found to be the most significant factor that affects satisfaction of department of dental technology(Adjusted $R^2$=48.3%). Conclusion: The extend of satisfaction of the women is low. The extend of satisfaction reduces as the grade increases. The school subject extend of satisfaction can know that ratio about of considering the leave of absence and voluntary withdrawal increases. Therefore, the plan of education that women can adapt the women o the school subject well and that it can be satisfied is sought for. It is considered that effort promoting the extend of satisfaction is needed as the grade increases.

• Journal of the Korean Ceramic Society
• /
• v.40 no.9
• /
• pp.874-880
• /
• 2003

The effect of h-BN content on microstructure, mechanical properties, and machinability of AlN-BN based machinable ceramics were investigated. The relative density of sintered compact decreased with increasing h-BN content. The four-point flexural strength also decreased from 238 MPa of monolith up to 182 MPa by the addition of 30 vol％ h-BN. Both low Young's modulus and residual tensile stress, formed by the thermal expansion coefficient difference between AIN and h-BN, might cause the strength drop in AlN-BN composite. The crack deflection, and pull-out phenomena increased by the plate-like h-BN. However, the fracture toughness decreased with h-BN content. The second phases, consisted of YAG and ${\gamma}$-Al$_2$O$_3$, were formed by the reaction between Al$_2$O$_3$ and Y$_2$O$_3$. During end-milling process, feed and thrust forces measured for AlN-(10～30) vol％ BN composites decreased with increasing h-BN particles, showing excellent machinability. Also, irrespective of h-BN content, relatively good surfaces with roughness less than 0.5 m (Ra) could be achieved within short lapping time.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.41 no.4
• /
• pp.263-270
• /
• 2017

The shipbuilding industry uses large stationary tanks to store low-pressure air, which is used to open and close large shut-off valves. However, when supplying air from the tank to a distant valve, there are problems related to the need for supplementary pipes and the pressure drop during transportation. In this study, a portable welded vessel for storing high-pressure nitrogen (11 kg, 10 L, and 50 bar) was designed to prevent air leakage and improve the convenience of workers. This pressure vessel was elliptical to reduce the number of welded parts, which are structurally weak. The thickness and ratio of the major and minor axes of the pressure vessel were calculated to verify its structure stability at the working pressure (50 bar), and that the proposed weight and capacity were satisfactory. The residual stress caused by the welding process was calculated by performing a transient thermal-structural coupled field analysis using the ANSYS parametric design language (APDL), and the fatigue life of the vessel was verified based on the Goodman criterion.

• Proceedings of the Korean Society of Dyers and Finishers Conference
• /
• 2011.11a
• /
• pp.47-47
• /
• 2011

국내의 기능성 난연성 섬유 제조기술은 원사 자체에 난연제가 포함된 상태인 난연 PET 원사나, 일반 PET 원단에 후방염 처리한 원단이 사용되기에 난연 방염성능이 만족스럽지 못하고 친환경적이지 못한 실정이다. 오늘날 세계 난연섬유 시장 규모는 10조원에 이르고 있으며 국내에서도 화재에 대한 경각심이 높아지는 추세이므로 기능성을 갖춘 고부가가치 난연소재의 개발이 시급하다. 폴리페닐렌술피드(PPS)는 내열성 및 내화학약품성이 뛰어난 열가소성 고분자로 용융방사가 가능하다. 난연성이 높은 양모섬유 또는 아크릴계 난연섬유, 아라미드 섬유 등은 비용 문제로 범용화에 한계가 있으므로 비교적 저렴한 PPS 섬유가 개발될 경우 범용화를 기대할 수 있다. 현재는 PPS 섬유가 특수한 용도에 주로 사용되고 있으나 우수한 난연 특성을 이용하여 일반 용도로의 사용 및 수요가 급격히 늘어날 것으로 예상되며 우선적으로 인테리어용 원단, 특히 커튼이나 소파용 원단으로 용도 전개가 가능할 것으로 판단하였다. 본 연구에서는 소파용 PPS 원단의 후가공 조건의 선정 및 불소계 발수방오가공을 위한 최적의 조건을 선정하고자 하였다. Padding(wet pick up율 $80{\pm}3%$)-Drying($105^{\circ}C$, 2.5min)-Curing은 시간은 1분으로 고정시킨 후, 온도를 150, 160, 170, 180, 190, $200^{\circ}C$에서 처리하여 Yellowness값을 측정한 결과, 온도가 높아질수록 Yellowness값이 커지는 것으로 미루어 보아 PPS원단은 높은 열에 영향을 받아 황변 현상이 일어나는 것으로 사료된다. 특히 $180^{\circ}C$를 기점으로 값에 큰 변화를 보였으므로 최적의 열처리 온도는 $170^{\circ}C$로 선정하여 이후의 실험을 진행하였다. 또한 큐어링 시간이 황변에 미치는 영향을 분석한 결과 온도에 의한 영향에 비해 적은 편으로 사료되었으나, 1.5min을 기점으로 Yellowess값이 높아졌으므로 최적의 열처리 시간을 1분으로 선정하였다. 최종 가공조건인 $170^{\circ}C$, 1분에서 처리한 시험포는 처리전 원단과 비교하였을 때, ${\Delta}$Yellowness가 2.84 정도로 나타났다. 그 후, PPS 원단에 불소가공제 (TG-991N, 동인텍스켐)의 적정 농도를 선정하기 위해 1~7%까지 농도를 높이며 처리한 결과, 불소가공제의 농도가 높아짐에 따라 황변현상이 나타남을 알 수 있었다. 농도가 높아짐에 따라 Yellowness값은 증가하다가 4% 이후 완만해지는 것을 알 수 있었으므로 IPA/Water Drop test와 발수도시험 (KS K 0590;2008)을 통해 적정 농도를 선정하였다. PPS 원단은 불소가공제의 농도가 높아짐에 따라 발수도가 우수해졌으며, 가공제 농도 3% 처리만으로도 우수한 발수도를 나타내었으나 100% 발수를 위해서는 가공제 농도가 5% 이상 처리되어야 하는 것을 확인할 수 있었다.

• Proceedings of the KWS Conference
• /
• 2009.11a
• /
• pp.119-119
• /
• 2009

인버터 DC 저항용접의 적용성 증대 : 인버터 DC 저항용접 공법이 SPOT, PROJECTON, SEAM, BUTT 등의 공정에 다양하게 적용되어 저항용접 현장에서 고효율, 친환경적 용접 환경을 만드는데 일조 하고 있다. 특히 자동차의 경량화, 충돌내성 증대, 진동 및 내구성 증대, 공간활용 극대화, 새로운 Design 개념 적용 등의 산업전반에 걸쳐 나타나는 신 Trends로 고 장력 철재의 적용 범위가 확대되고 HSS(High Strength Steel), EHSS(Extra High Strength Steel), UHSS (Ultra High strength Steel ; Hot - Formed Steel )등 다양한 철판의 SPOT 저항용접이 필요하게 되었다. 기존의 AC 단상용접의 전력 특성 상 통전 중 무 통전 시간 과 높은 PEAK 전력, 단상 대 전력 소모로 인한 전력 DROP 등의 문제로 인하여 신소재의 용접 시 매우 많은 Spatter가 발생하고, 높은 용접품질의 확보가 어려워 지므로 이를 대체하기 위한 공법으로 MFDC ( 인버터 DC 저항용접공법 )이 적용되고 있다. 인버터 DC 저항용접의 적응제어 : MFDC라는 높은 효율의 용접 전력원이 확보 됨에도 불구하고 용접현장에서는 원 자재, 도금 등의 품질 산포, 프레스 물의 가공산포, 공기압 산포, 전극 과열 및 마모 등의 요인에 의하여 저항용접 산포가 발생하고 있다. 이는 인위적인 조작이 어렵고 불규칙적이며, 어디서나 산재하고 있는 문제이다. 이를 용접전력 제어 법으로 개선하여 일정한 용접성을 확보하기 위한 노력이 적응제어 기법이다. 정 전류, 정 전력 제어는 정량 제어로 용접 물을 비롯한 용접부의 변화와는 관계없이 설정된 일정량의 전력을 공급하기만 하는데 반하여 적응제어는 적절한 용접 작업 시의 용접 물의 상태, 전극의 가압, 표면 상태 등에 따른 변화 페턴을 기억하고 이후 진행되는 용접에 대하여 정상 페턴과의 차이를 감지 이를 보상하므로 고품질의 용접성을 보장하는 제어기법이다. 따라서 다양한 용접 산포 유발 요인에 의해 용접부의 변화가 발생한다 하여도 그 변화를 감지 하고 적절한 용접전력을 공급한다면 고품질의 용접성을 확보하는데 유용한 공법이 될 수 있다. 인버터 DC 저항용접의 SPC 관리 : SPOT 용접 시 획득할 수 있는 다양한 파라메터에 대하여 모니터링 하고 이 자료를 data 화 하여 품질 관리에 응용하게 되면 양산라인에서 반복적으로 발생되는 문제점을 확인 할 수 있고 이를 통계적 방법으로 추적 개선해 나간다면 용접 불량 감소 및 생산성 향상에 도움이 되며 작업자의 공정 능력 향상 및 기업의 기술축적에도 높은 기여를 할 수 있을 것이다. 용접 적응제어와 다양한 파라메터 모니터링이 한 system에서 이루어 질 때 높은 용접성 확보와 불량률 감소, 원가절감, 생산성 향상 등의 효과가 극대화 될 것이다.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.11 no.10
• /
• pp.1899-1909
• /
• 2007

A cross-coupled charge pump with internal pumping capacitor, witch is advantages from a point of minimizing TFT-LCD driver IC module, is newly proposed in this paper. By using a NMOS and a PMOS diode connected to boosting node from VIN node, the pumping node is precharged to the same value each pumping node at start pumping operation. Since the lust-stage charge pump is designed differently from the other stage pumps, a back current of pumped charge from charge pumping node to input stage is prevented. As a pumping clock driver is located the font side of pumping capacitor, the driving capacity is improved by reducing a voltage drop of the pumping clock line from parasitic resistor. Finally, a layout area is decreased more compared with conventional cross-coupled charge pump by using a stack-MIM capacitors. A proposed charge pump for TFT-LCD driver IC is designed with $0.13{\mu}m$ triple-well DDI process, fabricated, and tested.

• Journal of Marine Life Science
• /
• v.6 no.2
• /
• pp.97-105
• /
• 2021

Tegillarca granosa, is one of the most important fishery resources throughout Asia. However, due to industrialization factories, marine environmental pollution, and global warming, the marine fishery production has drop sharply. In order to understand the genetic factors of the blood clam, which is a major fishery resource on the southern coast of Korea, the whole genome of blood clam was studied. The assembled genome of T. granosa was 915.4 Mb, and 19 chromosomes were identified. 25,134 genes were identified, and 22,745 genes were functionally annotated. As a result of performing gene gain and loss analysis between the blood clam genome and eight other types of shellfish, it was confirmed that 725 gene groups were expanded, and 479 gene groups were contracted. The homeobox gene cluster of blood clam showed a well-preserved genetic structure within lophotrochozoan ancestor. T. granosa genome showed high similarity between three hemoglobin genes with Scarpharca broughtonii. The blood clam genome will provide information for the genetic and physiological characteristics of blood clam adaptation, evolution, and the development of aquaculture industry.