• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.30 no.3
• /
• pp.239-248
• /
• 2017

According to the structure, solenoid valve can be categorized as spool valve or poppet valve. While various research on spool valve which has simple structure and fine susceptibility to contamination has been conducted, poppet valve which has less susceptibility to contamination and advantage in a long time operation still need much research because of its complicated structure. In order to design the poppet valve, various parameters such as the diameter of the poppet, the angle of the poppet, the diameter of the disk, the spring stiffness, the spring preload and flow path structure should be considered. Conventional studies on poppet valve usually take only one design parameters and did not much focused on the effect of the parameters on flow characteristics. In this paper, the change of the flow characteristics according to the design parameters of the poppet valve for 3/2Way solenoid valve is analyzed. The previous studies and the results of initial model analysis was referred for the selection of the design parameters. The effects of design parameters on maximum pressure, minimum pressure, and pressure drop was examined using analysis of means(ANOM).

• International Journal of Advanced Culture Technology
• /
• v.3 no.1
• /
• pp.21-30
• /
• 2015

Ceramic foams are prepared as positive images corresponding to a plastic foam structure which exhibits high porosities (85-90%). This structure makes the ceramic foams attractive as a catalyst in a dry reforming process, because it could reduce a high pressure drop problem. This problem causes low mass and heat transfers in the process. Furthermore, the reactants would shortly contact to catalyst surface, thus low conversion could occur. Therefore, this research addressed the preparation of dry reforming catalysts using a sol-gel catalyst preparation via a polymeric sponge method. The specific objectives of this work are to investigate the effects of polymer foam structure (such as porosity, pore sizes, and cell characteristics) on a catalyst performance and to observe the influences of catalyst preparation parameters to yield a replica of the original structure of polymeric foam. To accomplish these objectives industrial waste foams, polyurethane (PU) and polyvinyl alcohol (PVA) foams, were used as a polymeric template. Results indicated that the porosity of the polyurethane and polyvinyl alcohol foams were about 99% and 97%. Their average cell sizes were approximate 200 and 50 micrometres, respectively. The cell characteristics of polymer foams exhibited the character of a high permeability material that can be able to dip with ceramic slurry, which was synthesized with various viscosities, during a catalyst preparation step. Next, morphology of ceramic foams was explored using scanning electron microscopy (SEM), and catalyst properties, such as; temperature profile of catalyst reduction, metal dispersion, and surface area, were also characterized by $H_2-TPR$ and $H_2-TPD$ techniques, and BET, respectively. From the results, it was found that metal-particle dispersion was relatively high about 5.89%, whereas the surface area of ceramic foam catalysts was $64.52m^2/g$. Finally, the catalytic behaviour toward hydrogen production through the dry reforming of methane using a fixed-bed reactor was evaluated under certain operating conditions. The approaches from this research provide a direction for further improvement of marketable environmental friendly catalyst production.

• Korea journal of population studies
• /
• v.16 no.2
• /
• pp.1-23
• /
• 1993

Korea fertility level has dropped since the 1960's and speed of decline has accelerated in the 1980's. In the resuls, the growth rate reached to less then 1 percent in 1990 and will be $\ulcorner$0 $\lrcorner$ percent growth in 2021. The total population will increase to 50, 586 thousand persons in 2021 then will decrease. With the rapid fertility decline the age structure of Korean population has changed : while the proportion of child population aged 0-14 is decreasing sharply, that of old-age population aged 65 and over is increasing. Because of the recent increase of sex ratio at birth, the sex structure among the young generation has been destorted; the sex ratio at age 0-4 was as high as high as 112.0 in 1990. The effects of these population phenomena on Korean society are the followings: 1) Old age dependency ratio is increasing rapidly and continuously and will be about 40.0 from the 2050's. 2) Because of the rapid decline of the number of births, the absolute number of the major labour force at age 25-34 will decrease after around 2000 and then from the 2010's become less than that in 1990. 3) Since the large fertility defferentials by womens's educational level have continued and the relation between the educational levels of mothers and children are very strong, level has dropped among higher educated women first when the average fertility level has declined in Korea, the average educational level of the children is may be expected to be relatively low and then the future productivity is will be also low, which causes the decline of 'quality of population. 4) When the high sex ratio at birth (over 110 since 1986) continues, number of brides will be short by over 20 percent from the 2010s, which will bring various kinds of social prblems. Therefore, the counter measures in concrete to relieve the heavy problems are recommended as follows: 1) The extention of the birth intervals, which helps to drop the population growth rate at the same level of number of children per women. 2) The positive supports for out-migrants, which helps to reduce the population size without any destortion of age-sex structure. 3) The defferent supports of family planning for the higher and lower classes, which helps to reduce the gaps between different ferility levels of the classes and to keep and improve the quality of population. 4)population education for both students and adults, which helps to minimize the gap between the private and public requirements.

• Korea journal of population studies
• /
• v.17 no.1
• /
• pp.1-16
• /
• 1994

Since 1962, the population growth control has been one of the most important aims in the 5-Year So-cioeconomic Development Plans of Korea. The annual population growth rate has dropped to tess than 1 percent in 1990 from about 3 percents in 1960s, and projected to reach to $\ulcorner$0$\urcorner$ percent in 2021. From 2021, Korean population will decrease and the age structure will be distorted because birth rate will drop suddenly and continuously. Thus, we can consider $\ulcorner$0$\urcorner$ growth population for minimizing the prob- lems on the decreasing population. To discuss the problems caused from the changes of population size and age- sex composition, we projected three kinds of population including two kinds of $\ulcorner$0$\urcorner$ growth population under different as- sumptions. The first is the population which extended the projection of National Statistical Office up to 2090. Because the TFR is assumed and fixed as low as 1.63 after 1990, the population growth rate will be under $\ulcorner$0$\urcorner$ in 2021 and drop by about 1 percent every year from around 2050. This population trend results to old age population : 38.1 of old- age dependency ratio and 46.5 years of median age. The second is the population which the size in 2021 projected by the NOS continues after 2021. To change over from the decreasing population after 2021 to the $\ulcorner$0$\urcorner$ growth one, the TFR should be in-creased up to over 3.0 in 2040-2050, which fertility level would be too high to be accepted. The third is the population which approaches to the $\ulcorner$0$\urcorner$ growth population under the assumptions that the TFR increases from 1.63 to 2.1 in the period of 2010-2030 and then the same level continues. Although the maximum population size reaches 51, 503 thousand persons, the population will approach to the stationary population with about 42.4 million persons around 2090. In this projected population there is no more serious problems on population composition, on the rapid decrease of population, and on the increase TFR level. When the $\ulcorner$0$\urcorner$ growth population continues the problems of over population caused by the populationincrease wou]d be minimized, and the problems of unusual age composition resulted from the popula-tion decrease would not be found any more. Furthermore, when the changes of population size and composition is continuing slowly, the factors of population would effect moderately to socioeconomic development and help social changes. Therefore, with the attention of the present population changes, we should adapt new and detailde population policy which is able to get the $\ulcorner$0$\urcorner$ growth population.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.23 no.5
• /
• pp.595-602
• /
• 2017

In Korea, much research and development have occurred to enhance the technological competitiveness of tuna purse seining fisheries. Due to these efforts, fishing efficiency has been improved with the development of radar, sonar and global positioning systems for fish detection and revisions to the hull forms of tuna purse seiners. However, for skiff boats, net boats and speed boats, which are auxiliary working boats mounted on tuna purse seiners, technology has lagged behind relative to the modernization of the main vessel. In this study, the hull of an existing propeller-based net boat with steel wire net to protect tuna was changed to the hull of a water jet propulsion vehicle to reduce resistance and improve maneuverability. As a result, a prototype of a water jet propulsion option was produced according to the aluminum structure strength standards specified by the Ministry of Oceans and Fisheries, and safety was confirmed by performing a drop test. Moreover, through a sea trial test, an existing net boat was shown to have a speed of 12.0knots and a towing force of 2,545 kgf at 2,500 RPM. The prototype had a speed of 26.7 knots and a towing force of 2,011 kgf at 3,200 RPM, which satisfied the towing capacity standards of auxiliary working boats mounted on tuna purse seiners.

• Polymer(Korea)
• /
• v.24 no.1
• /
• pp.97-104
• /
• 2000

PAN-based activated carbon fibers/phenolic resin matrix composites (ACFCs) were manufactured via molding process with oxidized carbon fabrics (plain-type) and phenolic resin (resole-type) compounded by 70 : 30 wt%. The green body (as molded) was submitted to carbonization (at 100$0^{\circ}C$) in an inert environment and activation (at 700, 800, 900 and 100$0^{\circ}C$) in a $CO_2$ environment. In this work, the influence of activation temperatures was investigated in surface properties, such as pH, acid- and base-values by titration method, and in adsorption properties, i.e., specific surface area and pore structures by BET-method of the composites. Also, the pressure drops of the specimens were calibrated by ASTM. As a result, the activation temperature influenced the surface property of ACFCs. When the activation temperature was higher than 90$0^{\circ}C$, the surface was gradually developed in basic nature. And, the evolutions of specific surface area, total pore volume and pore size distribution of ACFCs could be easily confirmed the dependence on the activation temperature. Among them, well-developed pore structure from adsorption characteristics was changed of the ACFCs activated at 90$0^{\circ}C$. Also, the pressure drop was slightly decreased with increasing the temperature due to increasing the burn-off with heat treatment temperature of ACFCs.

• Journal of KIISE:Software and Applications
• /
• v.32 no.10
• /
• pp.1003-1012
• /
• 2005

The most significant difference of embedded systems from general purpose systems is that embedded systems are allowed to use only limited resources including battery and memory. Especially, the number of applications increases which deal with multimedia data. In those systems with high data computations, the delay of memory access is one of the major bottlenecks hurting the system performance. As a result, many researchers have investigated various techniques to reduce the memory access cost. Most programs generally have locality in memory references. Temporal locality of references means that a resource accessed at one point will be used again in the near future. Spatial locality of references is that likelihood of using a resource gets higher if resources near it were just accessed. The latest embedded processors usually adapt cache memory to exploit these two types of localities. Processors access faster cache memory than off-chip memory, reducing the latency. In this paper we will propose the enhanced dynamic allocation technique for structure-type data in order to eliminate unused memory space and to reduce both the cache miss rate and the application execution time. The proposed approach aggregates fields from multiple records dynamically allocated and consecutively remaps them on the memory space. Experiments on Olden benchmarks show $13.9\%$ L1 cache miss rate drop and $15.9\%$ L2 cache miss drop on average, compared to the previously proposed techniques. We also find execution time reduced by $10.9\%$ on average, compared to the previous work.

• Journal of Korea Water Resources Association
• /
• v.49 no.10
• /
• pp.809-821
• /
• 2016

The study area is local river of 671 (total length 3,741 km) in Gyeongnam prefecture, the results are as follows. Total number of river-crossing structures was investigated as 7,730, and it was found that structures were installed in 2.1 sites per 1 km (river length) on average. Diversion weirs for agriculture were 4006 (51.82%) and drop structures for channel bed maintenance were 3670 (47.48%), but the rest (riverbed road etc.) were 54 (0.70%). The number of high structures (height > 1.0 m) that affect many impact in upstream and downstream was investigated as 3,897 (51%), and the number of low structures (height < 0.5 m) that affect negligibly was 1109 (14%). Fish ladders have been installed on 640 (8%) structures in 153 (23%) rivers. In flood control and environment conservation, river-crossing structures brought about various impact that flood water level is raises and the eco-corridor is intercept. In order to improve these problems, we proposed a few engineering measures that can be realize with respect to river-crossing structures.

• Journal of Korea Water Resources Association
• /
• v.52 no.5
• /
• pp.313-323
• /
• 2019

Deep Tunnel system is a large-scale urban flood control facility installed underground in order to reinforce the lack of drainage systems in developed cities. In a structure like a deep tunnel system, the undular bore generated in the downstream causes a problem in the hydraulic stability of the tunnel. In this study, to investigate the influence of the undular bore on the hydraulic stability at the "Shinwol rainwater storage and drainage system", under construction for the first time in the country, a hydraulic model experiment was conducted on various flooding inflow scenarios. As a result of the hydraulic model experiment carried out in this study, the undular bore generated downstream is trapped in the pipe while moving to upstream, pushes the compressed air. It is judged that overflow occurred by choking the vertical drop shaft in the process when this compressed air is being exhaust through the upstream vertical drop shaft and blocking flood inflow. In addition, the analysis of velocity of undular bore shows that the undular bore transfers energy, and at this time, the pressure rose in the pipe and the velocity increment occurred of the undular bore. Further studies are needed to predict the size and velocity of undular bore, which plays an important role in the hydraulic stability of the tunnel in the deep tunnel system.

• The Journal of Korean Academy of Prosthodontics
• /
• v.46 no.3
• /
• pp.307-319
• /
• 2008

STATEMENT OF PROBLEM: It is known that an anodic oxidation technique, one of the methods for the implant surface treatment, remarkably increased surface area, enhanced wettability and accelerated the initial bone healing. Purpose: This study was performed to evaluate the wettability of anodized titanium surface which has a nanotubular structure, to assess osseointegration after the placement of implant with nano-size tubes on tibia of rats and to analyze quantitatively transferable rhBMP-2 on each surface. MATERIAL AND METHOD: Four different kinds of surface-treated titanium discs (polished (machined surface) group, micro (blasting surface) group, nano (anodizedmachined surface) group, and nano-micro (anodized-blasting surface) group) were fabricated (n=10). Three different media were chosen to measure the surface contact angles; distilled water, plasma and rhBMP-2 solution. After a single drop (0.025 $m{\ell}$) of solution, the picture was taken with the image camera, and contact angle was measured by using image analysis system. For the test of osseointegration, 2 kinds of anodized surface (anodized-machined surface, anodized-blasting surface) implants having 2.0 mm in diameter and 5.0 mm in length inserted into the tibia of Wistar rats. After 3 weeks, tibia were harvested and the specimens were stained with hematoxylin and eosin for histological analysis. To test the possibility of drug delivery, after soaking sample groups in the concentration of 250 ng/$m{\ell}$l of rhBMP-2 for 48 hours, the excess solution of rhBMP-2 were removed. After that, they were lyophilized for 24 hours, and then the rhBMP-2 on the surface of titanium was resolved for 72 hours in PBS. All the extracted solution was analyzed by ELISA. One-way analysis of variance (ANOVA) was performed on the data. RESULTS: The wettability is improved by anodic oxidation. The best wettability was shown on the nano-micro group, and it was followed by nano group, micro group, and polished group. In the histological findings, all implants showed good healing and the new bone formation were observed along the implant surface. After 3 days, nano-micro group delivered the most amount of rhBMP-2, followed by nano group, micro group, and polished group. CONCLUSION: It indicated that anodic oxidation on blasting surface produce functionally graded nano-micro porous structure and enhance hydrophilicity of the surface and osseointegration. The findings suggest that the nano-micro porous structure could be a useful carrier of osteogenic molecules like rhBMP-2.