• Journal of Power Electronics
• /
• v.17 no.1
• /
• pp.222-231
• /
• 2017

In this paper, a new architecture for a cost-effective power conditioning systems (PCS) using a single-sourced asymmetric cascaded H-bridge multilevel inverter (MLI) for photovoltaic (PV) applications is proposed. The asymmetric MLI topology has a reduced number of parts compared to the symmetrical type for the same number of voltage level. However, the modulation index threshold related to the drop in the number of levels of the inverter output is higher than that of the symmetrical MLI. This problem results in a modulation index limitation which is relatively higher than that of the symmetrical MLI. Hence, an extra voltage pre-regulator becomes a necessary component in the PCS under a wide operating bias variation. In addition to pre-stage voltage regulation for the constant MLI dc-links, another auxiliary pre-regulator should provide isolation and voltage balance among the multiple H-bridge cells in the asymmetrical MLI as well as the symmetrical ones. The proposed PCS uses a single-ended DC-DC converter topology with a coupled inductor and charge-pump circuit to satisfy all of the aforementioned requirements. Since the proposed integrated-type voltage pre-regulator circuit uses only a single MOSFET switch and a single magnetic component, the size and cost of the PCS is an optimal trade-off. In addition, the voltage balance between the separate H-bridge cells is automatically maintained by the number of turns in the coupled inductor transformer regardless of the duty cycle, which eliminates the need for an extra voltage regulator for the auxiliary H-bridge in MLIs. The voltage balance is also maintained under the discontinuous conduction mode (DCM). Thus, the PCS is also operational during light load conditions. The proposed architecture can apply the module-integrated converter (MIC) concept to perform distributed MPPT. The proposed architecture is analyzed and verified for a 7-level asymmetric MLI, using simulation results and a hardware implementation.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.272-272
• /
• 2010

We have fabricated alumina thick films by inkjet printing technology. Two different types of ink system were formulated in order to understand their evaporation behaviors and their evaporation effects on the powder distribution on, the surface during inkjet-printed alumina thick films. Single solvent system was formulated with N,N-dimethylformamide(DMF), which led to coffee ring effects which non-uniformly distributed alumina particles on the substrate during the ink evaporation. However, Co-solvent system which consists of both Water and DMF produced relatively uniform distribution of the particles on the substrate. We believe that these two different distributions of alumina particles are attributed to the ink fluid flow directions in the ink droplets ejected from the different ceramic ink system. We have modulated inkjet parameters such as dot-to-dot distance, line-to-line distance, jetting velocity and jetting drop size in order to find out the optimum condition for the printing of alumina thick films from two different ink systems. The surface roughness, microstructures and dielectric properties of these inkjet-printed alumina thick films were investigated.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.35 no.4
• /
• pp.353-360
• /
• 2011

The prediction of binary droplet collisions is important in the formation of falling drops and the evolution of sprays. The droplet velocity, impact parameter, and drop-size ratio influence the interaction between the droplets. The effect of these parameters results in complicated collision phenomena. Droplet collisions can be classified into four types of interactions: bouncing, coalescence, reflexive separation, and stretching separation. In the present study, the interfacial flow problem of the droplet collision was numerically simulated by using the level set method. 2D axisymmetric simulations on the head-on collisions and 3D simulation on the off-center collisions were performed. The numerical results of droplet behavior after the collision agreed well with the experimental and analytical results. The mixing of the mass of the initial droplets after the collision was also predicted by using different species index of colliding droplets.

• Journal of ILASS-Korea
• /
• v.5 no.1
• /
• pp.5-12
• /
• 2000

The beneficial aspects of applying emulsion fuels to combustion systems may be due to the changes of fuel properties which lead to the enhanced atomization characteristics. The spray characteristics of water/oil emulsified fuel injected from the pressure-swirl(simplex) atomizer using for oil burner were investigated. Four different water contents from 10 to 40 % by volume at 10% increment were prepared by mixing with the different contents of surfactants. Total amount of surfactant used was varied from 1 to 3 % by volume. This study demonstrates the influence of water and surfactant contents of emulsified fuel, injection pressure on the spray characteristics, i.e. Sauter mean diameter(SMD) and spray angle. The drop size distribution of the emulsified fuel spray was measured with a Malvem particle sizer. In order to measure the spray angle, the digital image processing was employed by capturing multiple images of the spray with 3-CCD digital video camera. It was evident that the addition of water and surfactant changes fuel properties which are the key parameters influencing the atomization of the spray. The increase in surfactant content results in the decrease of SMD and the increase in spray angle. The droplets decease with increase in injection pressure, but the influence of injection pressure in this experimental condition was less important than expected. The more viscous fuel with the increase of water content exhibits the larger droplets in the centerline of the spray, and the less viscous fuel in the outer edges of the spray. The increase in axial position from the nozzle causes the spray angle to decrease. The spray angle decreases with increase in water content. This is due to increase in viscosity with increase in water content.

• Journal of the Korean Chemical Society
• /
• v.48 no.2
• /
• pp.137-143
• /
• 2004

The determination of 2-mercapto-1-methyl-imidazole (MMI) in 5.0${\times}10^{-2}$ M lithium perchlorate suporting electrolyte has been investigated by the differential pulse polarography. The optimum condition of MMI analysis was as follows; -0.9 volts initial potential, 0.08 mV pulse height, 2 mV/sec scan rate, and medium mercury drop size. Standard calibration curve showed a good linearlity in the range of 1.0${\times}10^{-7}M\;to\;8.0{\times}10^{-5}$ M and the detection limit has been (2.2${\pm}0.1){\times}0.1^{-9}$ M. This method was applicated for the determination of MMI in antithyroid drug without interference of additives.

• Proceedings of the SAREK Conference
• /
• 2009.06a
• /
• pp.751-756
• /
• 2009

In the perspective of saving energy in buildings, the high performance of insulation and air tightness for improving the heating and the cooling efficiency, has brought economically positive effects. However, these building energy saving technologies cause the lack of ventilation, which is the direct cause of increasing the indoor contaminants, and is also very harmful to the residents, because they spend over 90% of their time indoors. Therefore, the ventilation is important to keep the indoor environment clean and it can also save the energy consumption. In this study, a HEPA type nano ceramic filter is designed as a passive ventilation system to collect airborne particles and to supply fresh outdoor air. The double layer filter, which has $30{\mu}m$ in diameter at the conditions of 10wt% of concentration and 3kV/cm of the electric intensity, is produced by electrospinning. The filtration coating technology is confirmed in the solution with $SiO_2$ nano particles using polymer nano fibers. Also double layer filters are coated with $SiO_2$ nano particles and finally the porous construction materials are made by sintering in the electric furnace at $200{\sim}1400^{\circ}C$. The efficiency is measured 96.67% at the particle size of $0.31{\mu}m$, which is slightly lower than HEPA filter. However the efficiency is turned out to be sufficient.

• Journal of Energy Engineering
• /
• v.7 no.1
• /
• pp.103-112
• /
• 1998

A high temperature fabric filter was developed and characterized in order to solve the various problems encountered in the operation of industrial fabric filters. Four kinds of dusts generated in the typical domestic industry were used for its characterization, coke dust from a steel manufacturing process, cement dust from a cement manufacturing process, fly ash from a fluidized-bed combustor, and incinerator ash from a waste plastics incinerator. The physical and chemical properties of the high temperature fabric filter were analyzed in terms of mean flow pore pressure, bubble point pore diameter, mean flow pore diameter, pore size distribution, and the changes in tensile strength and initial elastic modulus under $SO_2$ and $NO_2$ atmospheres. Pressure drop, dust penetration, and figure of merit for the fabric filter were also investigated in a bench-scale filter testing unit. The fabric filter developed in this study had good physical and chemical filter properties and showed a very applicability to typical industrial dusts treatments.

• Journal of Korean Society on Water Environment
• /
• v.30 no.3
• /
• pp.261-268
• /
• 2014

Four clays (both natural and commercial types) mainly used in Korea were tested for removal efficiency of Microcystis spp. and ecotoxicity on Daphnia magna and Vibrio fischeri. Four clays (clay A~D) were composed of 91.9~100% of sand (0.02~0.2 mm in particle size). Clay D consisted of lager particles than other clays. Major elements of the four clays were $SiO_2$ (45.3~62.8%), $Al_2O_3$ (18.5~29.7%) and $Fe_2O_3$ (5.4~7.9%). They contained kaolinite (clay mineral), quartz, muscovite, and so on. Clay C and D contained montmorillonite, one of the clay minerals improving clay-cell aggregation. For clay A, B and C, removal efficiency of Microcystis spp. was over 60% at 2 g/L. It reached about 100% at over 5 g/L. For clay D, it was over 60% and 95~100% at 5 g/L and 20 g/L respectively. After adding clays, pH decreased. The greatest drop of pH appeared at clay C. Except for addition of 100 g/L clay C, ecotoxicity on D. magna and V. fischeri didn't appeared at all dose of clays.

• Fashion & Textile Research Journal
• /
• v.13 no.4
• /
• pp.590-599
• /
• 2011

The purpose of this study is to classify body types into different groups based on 3D scanned data, and identify the representative body shapes that most frequently appear in the groups. A high frequency range was defined based on body measurement data, and representative shapes were identified based on body scan data of women aged 18-24. The major findings of this study are as follows. First, the three typical types of height, bust and drop mixes among Korean women aged 18-24 are as follows:) 155-88-N,) 160-82-A, and 165-85-A. Regarding the body type, the A and N types frequently appeared, while the H type was rare. Second, among the subjects of the high-frequency groups, upright bodies were selected as sample models and were used for morphing. An adjustment was made to the morphing results to reflect the body characteristics of the sample models evenly. Third, to verify the morphing results, the body sizes of the sample models and the created models were compared. The result showed that, the sizes were close to the average size of the sample models. Fourth, to verify whether the morphing processes adequately reflected the features of the body shapes, cross-section models of key body parts were made and the degree of representativeness was determined.

• Atmosphere
• /
• v.23 no.3
• /
• pp.321-329
• /
• 2013

This study examines the effect of aerosols on the vertical invigoration of continental stratiform clouds, using a dataset of Atmospheric Radiation Measurement (ARM) Intensive Operational Period (IOP, March 2000) at the Southern Great Plains (SGP) site. To provide further support to our observation-based findings, the weather research and forecasting (WRF) sensitivity simulations with changing cloud condensation nuclei (CCN) concentrations have been carried out for the golden episode over SGP. First, cross correlation between observed aerosol scattering coefficient and cloud liquid water path (LWP) with a 160-minutes lag is the highest of r = 0.83 for the selected episode, which may be attributable to cloud vertical invigoration induced by an increase in aerosol loading. Modeled cloud fractions in a control run are well matched with the observation in the perspective of cloud morphology and lasting period. It is also found through a simple sensitivity with a change in CCN that aerosol invigoration (AIV) effect on stratiform cloud organization is attributable to a change in the cloud microphysics as well as dynamics such as the corresponding modification of cloud number concentrations, drop size, and latent heating rate, etc. This study suggests a possible cloud vertical invigoration even in the continental stratiform clouds due to aerosol enhancement in spite of a limited analysis based on a few observed continental cloud cases.