• The Transactions of the Korean Institute of Electrical Engineers A
• /
• v.48 no.4
• /
• pp.461-466
• /
• 1999

A CMOS op amp with rail-to-rail input and output ranges is designed in a one-volt supply. The output stage of the op amp is used in a common source amplifier that operates in sub-threshold region to design a low voltage op amp with rail-to-tail output range. To drive heavy resistor and capacitor loads with rail-to-rail output ranges, a common source amplifier which has a low output resistance is utilized. A bulk-driven differential pair and a bulk-driven folded cascode amplifier are used in the designed op amp to increase input range and achieve 1 V operation. Post layout simulation results show that low frequency gain is about 58 ㏈ and gain bandwidth I MHz. The designed op amp has been fabricated in a 0.8${\mu}{\textrm}{m}$ standard CMOS process. The measured results show that this op amp provides rail-to-rail output range, 56㏈ dc gain with 1 MΩ load and has 0.4 MHz gain-bandwidth with 130 ㎊ and 1 kΩ loads.

• Journal of Institute of Control, Robotics and Systems
• /
• v.10 no.2
• /
• pp.164-170
• /
• 2004

Recently, the demand for micro hard disk drive that provides high-capacity removable storage for handhold electronic devices is growing very rapidly Reducing power consumption is one of the primary control objectives in micro disk drives. The input power delivered to the seek servo system is consumed as heat by the transistors of power amplifier and motor coil resistance. In this paper, we present a new seek servo controller for minimizing the power consumption. We use a Fourier decomposition and nonlinear programming to determine the optimum seek profile that minimizes the power consumption. Also, the trajectory tracking controller is developed for exact tracking of the optimum seek profile. Finally, we present some experimental results using a commercially available micro disk drive in order to demonstrate the superior performance of the proposed controller.

• Proceedings of the IEEK Conference
• /
• 2003.11c
• /
• pp.369-373
• /
• 2003

As most of the powerline modems use spread spectrum modulation method which has strong immunity against the narrowband fading, or psk modulation method, the amplitude of the signal contains no useful informations. In this paper, we used class D amplifier to implement the drive circuit of the analog front end, and showed that it has great superiority over other existing drive circuits in rapidly impedance changing powerline channel.

• Proceedings of the IEEK Conference
• /
• 2006.06a
• /
• pp.609-610
• /
• 2006

A 77GHz MMIC transceiver module consisting of a power amplifier, a low noise amplifier, a drive amplifier, a frequency doubler and a down-mixer has been developed for automotive forward-looking radar sensor. The MMIC chip set was fabricated using $0.15{\mu}m$ gate-length InGaAs/InAlAs/GaAs mHEMT process based on 4-inch substrate. The power amplifier demonstrated a measured small signal gain of over 20dB from $76{\sim}77GHz$ with 15.5dBm output power. The chip size is $2mm{\times}2mm$. The low noise amplifier achieved a gain of 20dB in a band between $76{\sim}77\;GHz$ with an output power of 10dBm. The chip size is $2.2mm{\times}2mm$. The driver amplifier exhibited a gain of 23dB over a $76{\sim}77\;GHz$ band with an output power of 13dBm. The chip size is $2.1mm{\times}2mm$. The frequency doubler achieved an output power of -16dBm at 76.5GHz with a conversion gain of -16dB for an input power of 10dBm and a 38.25GHz input frequency. The chip size is $1.2mm{\times}1.2mm$. The down-mixer demonstrated a measured conversion gain of over -9dB. The chip size is $1.3mm{\times}1.9mm$. The transceiver module achieved an output power of 10dBm in a band between $76{\sim}77GHz$ with a receiver P1dB of -28dBm. The module size is $8{\times}9.5{\times}2.4mm^3$. This MMIC transceiver module is suitable for the 77GHz automotive radar systems and related applications in W-band.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.44 no.6 s.360
• /
• pp.8-18
• /
• 2007

In this paper, a 4bit cell way structure of PoRAM and the sensing method to drive this structure are researched. PoRAM has a different operation from existing SRAM and DRAM. The operation is that when certain voltage is applied between top electrode and bottom electrode of PoRAM device we can classify the cell state by measuring cell current which is made by changing resistance of the cell. In the decoder selected by new-addressing method in the cell array, the row decoder is selected "High" and the column decoder is selected "Low" then certain current will flow to the bit-line. Because this current is detect, in order to make large enough current, the voltage sense amplifier is used. In this case, usually, 1-stage differential amplifier using current mirror is used. Furthermore, the detected value at the cell is current, so a diode connected NMOSFET, that is, a device resistor is used at the input port of the differential amplifier to converter current into voltage. Using this differential amplifier, we can classify the cell states, erase mode is "Low" and write mode is "High", by comparing the input value, Vin, that is a product of current value multiplied by resistor value with a reference voltage, Vref.

• Journal of Navigation and Port Research
• /
• v.27 no.1
• /
• pp.81-86
• /
• 2003

In the paper, the power amplifier using active biasing for LDMOS MRF-21060 is designed and fabricated. Driving amplifier using AH1 and parallel power amplifier AH11 is made to drive the LDMOS MRF 21060 power amplifier. The variation of current consumption in the fabricated 5 Watt power amplifier has an excellent characteristics of less than 0.1A, whereas passive biasing circuit dissipate more than 0.5A. The implemented power amplifier has the gain over 12 dB, the gain flatness of less than $\pm$0.09dB and input and output return loss of less than -19dB over the frequency range 2.11~2.17GHz. The DC operation point of this power amplifier at temperature variation from $0^{\circ}C$ to $60^{\circ}C$ is fixed by active circuit.

• Journal of Satellite, Information and Communications
• /
• v.3 no.1
• /
• pp.15-21
• /
• 2008

The high peak to average power ratio (PAPR) of OFDM (Orthogonal Frequency Division Multiplexing) system introduces inevitable non-linear distortion in the transmission due to the amplifier non-linear property. This causes both in-band distortion and out of band spectrum re-growth. In this paper we tried to compensate the problem by using polynomial based pre-distortion. Estimation of both the non-linear and inverse non-linear polynomial is achieved using the Least Square Error (LSE) method. Using these parameters closed form pre-distorter can be easily created. We also used the 'partial peak cancellation and clipping' method to remove the high peak present in the non constant amplitude of the OFDM signal responsible to drive the amplifier in near saturation region for better performance of the system

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.27 no.11
• /
• pp.83-91
• /
• 1990

VOC(coltage controlled oscillator) circuits are necessary in applications such at the demodul-ation of FM signals, frequency synthesizer, and for clock recovery from digital data. In this paper, we designed the VCO circuit based on a OTA(operational transconductance amplifier) and the OP amp which using a differential amplifier by BiCMOS circuit. It consists of a OTA, voltage contorolled integrator and a schmitt trigger. Conventional VCO circuits are designed using the CMOS circuit, but in this paper we designed newly BiCMOS VCO circuit which has a good drive avlity, As a result of SPICE simulation, output frequency is 141KHz at 105KHz, and sensitivity is 15KHz.

• Proceedings of the IEEK Conference
• /
• 2005.11a
• /
• pp.825-828
• /
• 2005

In this paper, we propose a new nonvolatile unit memory cell and proposal peripheral circuit using the polymer material. Memory that relies on bistable behavior- having tow states associated with different resistances at the same applied voltage - has attracted much interest because of its nonvolatile properties. Such memory may also have other merits, including simplicity of structure and manufacturing, and the small size of memory cells. We have plotted the load line graphs for the use of a polymer memory character, hence we have designed in the band-gap reference shape of a write/erase drive, and then designed in the 2-stage differential amplifier shape of a sense amplifier in the consideration of a low current characteristic of a polymer memory cell. The simulation result shows that is has high gain about 80dB by sensing the very small current.

• 한국정보통신설비학회:학술대회논문집
• /
• 2007.08a
• /
• pp.11-14
• /
• 2007

CMOS technology 기반의 고주파 직접회로에서는 충분한 이득과 안정성을 얻기 위하여 inductor, capacitor와 같은 수동 소자를 적절히 사용하여 설계하여야 한다. 이와 같은 수동 소자는 CMOS 집적회로에서 넓은 면적을 차지하는 단점이 있다. 고주파 증폭기의 부하를 능동 소자로 대체하게 되면 작은 크기로 회로의 제작이 가능하게 되나, 능동 소자는 수동 소자에 비하여 선형 특성이 좋지 않기 때문에 실제로 고주파 증폭기 설계에 사용하지 않는다. 본 논문에서는 이와 같은 능동 소자의 비선형성을 억제하면서, 동시에 회로의 크기를 줄일 수 있는 기능성 능동 부하를 적용한 고주파 증폭기를 설계하였다. 기능성 능동 부하는 2개의 MOSFET은 대칭으로 연결된 구조를 가지며, 하나의 MOSFET은 일반적인 load로 동작하며, 다른 MOSFET은 gate에 가변 전압을 인가함으로써, 증폭기의 전달함수를 변화시킬 수 있다. 이와 같은 특성을 이용하여 고주파 증폭기의 선형성을 보상할 수가 있다.