• 한국전기전자재료학회논문지
• /
• 제21권11호
• /
• pp.968-972
• /
• 2008

Ni/Ti/Al multilayer system ('/'denotes the deposition sequence) was tested for low-resistance ohmic contact formation to Al-implanted p-type 4H-SiC. Ni 30 nm / Ti 50 nm / Al 300 nm layers were sequentially deposited by e-beam evaporation on the 4H-SiC samples which were implanted with Al (norminal doping concentration = $4\times10^{19}cm^{-3}$) and then annealed at $1700^{\circ}C$ for dopant activation. Rapid thermal anneal (RTA) temperature for ohmic contact formation was varied in the range of $840\sim930^{\circ}C$. Specific contact resistances were extracted from the measured current vs. voltage (I-V) data of linear- and circular transfer length method (TLM) patterns. In constrast to Ni contact, Ni/Ti/Al contact shows perfectly linear I-V characteristics, and possesses much lower contact resistance of about $2\sim3\times10^{-4}\Omega{\cdot}cm^2$ even after low-temperature RTA at $840^{\circ}C$, which is about 2 orders of magnitude smaller than that of Ni contact. Therefore, it was shown that RTA temperature for ohmic contact formation can be lowered to at least $840^{\circ}C$ without significant compromise of contact resistance. X-ray diffraction (XRD) analysis indicated the existence of intermetallic compounds of Ni and Al as well as $NiSi_{1-x}$, but characteristic peaks of $Ti_{3}SiC_2$, a probable narrow-gap interfacial alloy responsible for low-resistance Ti/Al ohmic contact formation, were not detected. Therefore, Al in-diffusion into SiC surface region is considered to be the dominant mechanism of improvement in conduction behavior of Ni/Ti/Al contact.

• Current Photovoltaic Research
• /
• 제3권1호
• /
• pp.21-26
• /
• 2015

High efficiency $Cu(In,Ga)Se_2$ solar cells are generally prepared above $500^{\circ}C$. Lowering the process temperature can allow wider selection of substrate material and process window. In this paper, the three-stage co-evaporation process widely used to grow CIGS thin film at high temperature was modified to reduce the maximum substrate temperature. Below $400^{\circ}C$ the CIGS films show poor crystal growth and lower solar cell performance, in spite of external Na doping by NaF. As a new approach, Cu source instead of Cu with Se in the second stage was applied on the $(In,Ga)_2Se_3$ precursor at $400^{\circ}C$ and achieved a better crystal growth. The distribution of Ga in the films produce by new method were investigated and solar cells were fabricated using these films.

• 한국정보통신학회논문지
• /
• 제19권1호
• /
• pp.156-162
• /
• 2015

본 연구에서는 비대칭 이중게이트 MOSFET의 산화막두께, 채널도핑농도 그리고 상하단 게이트 전압 등과 같은 소자 파라미터에 따른 전도중심 및 전자농도가 문턱전압이하 스윙에 미치는 영향을 분석하고자 한다. 비대칭 이중게이트 MOSFET는 대칭구조와 비교하면 상하단 게이트 산화막의 두께 및 게이트 전압을 각각 달리 설정할 수 있으므로 단채널효과를 제어할 수 있는 요소가 증가하는 장점을 가지고 있다. 그러므로 상하단 산화막두께 및 게이트 전압에 따른 전도중심 및 전자분포의 변화를 분석하여 심각한 단채널효과인 문턱전압이하 스윙 값의 저하 현상을 감소시킬 수 있는 최적의 조건을 구하고자 한다. 문턱전압이하 스윙의 해석학적 모델을 유도하기 위하여 포아송방정식을 이용하여 전위분포의 해석학적 모델을 구하였다. 결과적으로 소자 파라미터에 따라 전도중심 및 전자농도가 크게 변화하였으며 문턱전압이하 스윙은 상하단 전도중심 및 전자농도에 의하여 큰 영향을 받는 것을 알 수 있었다.

• 한국산학기술학회논문지
• /
• 제11권3호
• /
• pp.827-834
• /
• 2010

발광층에 도펀트가 도핑된 다층 유기발광다이오드 소자 구조에서의 발광 메카니즘을 검증하기 위해 전기적인 특성요인들을 수치해석 하였다. 본 논문에 적용한 유기발광다이오드 소자는 ITO/NPB/$Alq_3$:C545T(%)/$Alq_3$/LiF/Al으로 이루어져 있으며 도펀트인 C545T의 도핑 농도를 변화시킨 4종류의 소자 구조에 대해 특성 변화를 검토하였다. 그 결과 도펀트의 도핑 농도 변화에 따라서 전압-전류 특성이 변화되어짐을 확인하였고, 이는 참고 문헌에 제시되어 있는 전압-전류밀도 실험 데이터와 매우 잘 일치되었다. 또한 도펀트를 도핑시킨 소자 구조들에서 전압-휘도 특성이 대폭 향상되어 발광효율이 3배정도 향상되었다. 이와 같은 guest-host system이 적용된 유기발광다이오드 소자의 동작 메카니즘을 분석하기 위하여 소자 내부에서의 전계분포, 전하분포, 재결합율 등의 전기적인 항목들에 대한 특성의 변화를 관찰하였다.

• 한국재료학회지
• /
• 제20권3호
• /
• pp.137-141
• /
• 2010

The $(1-x)La_{0.7}Sr_{0.3}MnO_3(LSMO)/xZnFe_2O_4$(ZFO) (x = 0, 0.01, 0.03, 0.06 and 0.09) composites were prepared by a conventional solid-state reaction method. We investigated the structural properties, magnetic properties and electrical transport properties of (1-x)LSMO/xZFO composites using X-ray diffraction (XRD), scanning electron microscopy (SEM), field-cooled dc magnetization and magnetoresistance (MR) measurements. The XRD and SEM results indicate that LSMO and ZFO coexist in the composites and the ZFO mostly segregates at the grain boundaries of LSMO, which agreed well with the results of the magnetic measurements. The resistivity of the samples increased by the increase of the ZFO doping level. A clear metal-to-insulator (M-I) transition was observed at 360K in pure LSMO. The introduction of ZFO further downshifted the transition temperature (350K-160K) while the transition disappeared in the sample (x = 0.09) and it presented insulating/semiconducting behavior in the measured temperature range (100K to 400K). The MR was measured in the presence of the 10kOe field. Compared with pure LSMO, the enhancement of low-field magnetoresistance (LFMR) was observed in the composites. It was clearly observed that the magnetoresistance effect of x = 0.03 was enhanced at room temperature range. These phenomena can be explained using the double-exchange (DE) mechanism, the grain boundary effect and the intrinsic transport properties together.

• Journal of Microbiology and Biotechnology
• /
• 제31권2호
• /
• pp.250-258
• /
• 2021

Among various species of marine bacteria, those belonging to the genus Halomonas have several promising applications and have been studied well. However, not much information has been available on their antibiotic resistance. In our efforts to learn about the antibiotic resistance of strain Halomonas socia CKY01, which showed production of various hydrolases and growth promotion by osmolytes in previous study, we found that it exhibited resistance to multiple antibiotics including kanamycin, ampicillin, oxacillin, carbenicillin, gentamicin, apramycin, tetracycline, and spectinomycin. However, the H. socia CKY01 resistance pattern to kanamycin, gentamicin, apramycin, tetracycline, and spectinomycin differed in the presence of 10% NaCl and 1% NaCl in the culture medium. To determine the mechanism underlying this NaCl concentration-dependent antibiotic resistance, we compared four aminoglycoside resistance genes under different salt conditions while also performing time-dependent reverse transcription PCR. We found that the aph2 gene encoding aminoglycoside phosphotransferase showed increased expression under the 10% rather than 1% NaCl conditions. When these genes were overexpressed in an Escherichia coli strain, pETDuet-1::aph2 showed a smaller inhibition zone in the presence of kanamycin, gentamicin, and apramycin than the respective control, suggesting aph2 was involved in aminoglycoside resistance. Our results demonstrated a more direct link between NaCl and aminoglycoside resistance exhibited by the H. socia CKY01 strain.

• 한국전기전자재료학회논문지
• /
• 제37권3호
• /
• pp.274-279
• /
• 2024

Eu³⁺-doped BaZrO₃ (BaZrO₃:Eu³⁺) phosphor powders were prepared using a solid-state reaction by changing the molar concentration of Eu³⁺ within the range of 0.5 to 30 mol%. Irrespective of the molar concentration of Eu³⁺ ions, the crystal structures of all the phosphors were cubic. The excitation spectra of BaZrO₃:Eu³⁺ phosphors consisted of an intense broad band centered at 277 nm in the range of 230~320 nm. The emission spectra were composed of a dominant orange band at 595 nm arising from the ⁵D₀→⁷F₁ magnetic dipole transition of Eu³⁺ and two weak emission bands centered at 574 and 615 nm, respectively. As the concentration of Eu³⁺ increased from 0.5 to 10 mol%, the intensities of all the emission bands gradually increased, approached maxima at 10 mol% of Eu³⁺ ions, and then showed a decreasing tendency with further increase in the Eu³⁺ ions due to the concentration quenching. The critical distance between neighboring Eu³⁺ ions for concentration quenching was calculated to be 11.21 Å, indicating that dipole-dipole interaction was the main mechanism of concentration quenching of BaZrO₃:Eu³⁺ phosphors. The results suggest that the orange emission intensity can be modulated by doping the appropriate concentration of Eu³⁺ ions.

• 한국결정성장학회지
• /
• 제22권5호
• /
• pp.241-246
• /
• 2012

본 연구에서는 complex citrate-gel method를 이용하여 $Yb3^{3+}$, $Er^{3+}$ 이온이 동시 도핑 된 $SrMoO_4$($SrMoO_4$: $Yb^{3+}/Er^{3+}$)를 성공적으로 합성하였으며, 그 구조적, 광학적 특성을 분석하였다. 980 nm의 근적외선 여기 광 하에서 상기 분말은 530 및 550 nm 부근의 강한 녹색 방출과 670 nm 부근에서의 약한 적색 방출은 $Er^{3+}$ 이온 내의 intra 4f transition $Er^{3+}$($^4F_{9/2}$, $^2H_{11/2}$, $^4S_{3/2}$) ${\rightarrow}$ $Er^{3+}(^4I_{15/2})$에 의한 현상임을 확인하였다. 또한, $Er^{3+}$ 및 $Yb^{3+}$ 이온의 최적 도핑 농도는 각각 2/16 mol%로 조사되었으며 그에 따른 형성 가능한 upconversion 메커니즘에 대하여 논의하였다.

• 대한화학회지
• /
• 제27권3호
• /
• pp.183-188
• /
• 1983

이산화황의 산화반응을 10 mol % $Ni-doped\;{\alpha}-Fe_2O_3$를 촉매로 하여 반응온도 범위 $320{\sim}440{\circ}C$에서 여러 산소 및 이산화황의 부분압으로서 반응속도를 측정하였다. 위 온도 영역에서 $SO_2$ 산화반응의 활성화에너지 값은 13.8 $kcal{\cdot}mol^{-1}$로서 얻어졌다. 반응속도 데이타는 산소에 대해서 0.5차, 이산화황에 대해서는 1차로서 전반응차수는 1.5차를 나타내었다. 이산화황과 산소를 여러 압력으로서 도입하여 전기전도도를 측정하였다. 반응속도 데이타와 전기전도도 데이타로 부터 반응기체들의 산화물계상에서 흡착메카니즘을 제안하였고, 촉매상에서 $SO_2$의 산화반응 메카니즘을 제안하였다. 산소와 이산화황은 이온상태로서 흡착하며, 산소는 니켈 dope로 인해 형성된 산소공위에 이산화황은 격자 산소에 흡착하였다. 반응속도 데이타와 전기전도도 데이타로부터 이산화황의 산화반응속도를 결정짓는 단계는 이산화황이 격자산소에 흡착하는 과정임을 알았다.

• 한국재료학회지
• /
• 제21권4호
• /
• pp.216-219
• /
• 2011

Perovskite manganites such as $RE_{1-x}A_xMnO_3$ (RE = rare earth, A = Ca, Sr, Ba) have been the subject of intense research in the last few years, ever since the discovery that these systems demonstrate colossal magnetoresistance (CMR). The CMR is usually explained with the double-exchange (DE) mechanism, and CMR materials have potential applications for magnetic switching, recording devices, and more. However, the intrinsic CMR effect is usually found under the conditions of a magnetic field of several Teslas and a narrow temperature range near the Curie temperature ($T_c$). This magnetic field and temperature range make practical applications impossible. Recently, another type of MR, called the low-field magnetoresistance(LFMR), has also been a research focus. This MR is typically found in polycrystalline half-metallic ferromagnets, and is associated with the spin-dependent charge transport across grain boundaries. Composites with compositions $La_{0.7}(Ca_{1-x}Sr_x)_{0.3}MnO_3)]_{0.99}/(BaTiO_3)_{0.01}$ $[(LCSMO)_{0.99}/(BTO)_{0.01}]$were prepared with different Sr doping levels x by a standard ceramic technique, and their electrical transport and magnetoresistance (MR) properties were investigated. The structure and morphology of the composites were studied by X-ray diffraction (XRD) and scanning electronic microscopy (SEM). BTO peaks could not be found in the XRD pattern because the amount of BTO in the composites was too small. As the content of x decreased, the crystal structure changed from orthorhombic to rhombohedral. This change can be explained by the fact that the crystal structure of pure LCMO is orthorhombic and the crystal structure of pure LSMO is rhombohedral. The SEM results indicate that LCSMO and BTO coexist in the composites and BTO mostly segregates at the grain boundaries of LCSMO, which are in accordance with the results of the magnetic measurements. The resistivity of all the composites was measured in the range of 90-400K at 0T, 0.5T magnetic field. The result indicates that the MR of the composites increases systematically as the Ca concentration increases, although the transition temperature $T_c$ shifts to a lower range.