• Journal of the Korean Chemical Society
• /
• v.42 no.1
• /
• pp.122-134
• /
• 1998

In this review, we describe the electrochemical properties of spinel-type lithium manganese oxides $(Li_xMn_2O_4)$ and their failure modes encountered in 4 V lithium rechargable cells. The long-term cyclability (reversibility) of spinel electrodes is determined partly by the purity, size and distribution of spinel particles, and also by the microstructure of electrode plates. A proper selection of electrolytes is another important task in cyclability enhancements. In the spinel preparation, impurity formation and cation mixing should be minimized. The carbon content in composite cathodes should also be minimized to the extent where the cell polarization does not bring about adverse effects on cell performances. The binder content should be optimized on the basis of dispersion of component materials and mechanical strength of the plates. Cathodic capacity losses arising from solvent oxidation and spinel dissolution can be mitigated by using electrolytes composed of carbonates and/or fluorine-containing lithium salts. The carbon additives may be selected after a trade-off between the cell polarization in composite cathodes and the solvent oxidation on carbon surface.

• Journal of Sensor Science and Technology
• /
• v.11 no.6
• /
• pp.327-334
• /
• 2002

Fine particles of $SnO_2$ were fabricated by the sol-gel powder processing using tine(II) chloride dihydrate($SnCl_2{\cdot}2H_2O$) and ethanol($C_2H_5OH$) as raw materials. The powders were investigated about the properties and electrical sensing. Gel powders were fabricated by drying of sol at $120^{\circ}C$ after aging 72hrs and 168hrs. The amount of $SnO_2$ phase was increased below $600^{\circ}C$ due to the elimination of volatile components, and the $SnO_2$ phase was almost completed by the heat treatment at $700^{\circ}C$ for 30min. The grain sizes were about 30nm below $700^{\circ}C$, and it showed the narrow distribution of the grain sizes. The specimens to measure electrical properties were fabricated by the thick film screen printing technique on the alumina substrates. The conductance of $SnO_2$ was showed the intrinsic behaviour of semiconducting ceramics above at $450^{\circ}C$. The constant conductance was observed in the temperature range of $200{\sim}450^{\circ}C$. The sensing properties of response time, recovery, and sensitivity of CO were improved with aging time.

• Journal of the Korean Ceramic Society
• /
• v.38 no.9
• /
• pp.799-805
• /
• 2001

Two commercial alumina powders having different particle size of $0.5{\mu}m$ and 3${\mu}$m were presintered at 1120$^{\circ}$C for 2h and then lanthanum aluminosilicate glass was infiltrated at 1100$^{\circ}$C for up to 4h to obtain the densified glass-alumina composites. The effect of alumina particle size on packing factor, microstructure, wetting, porosity and pore size, and mechanical properties of the composite was investigated. The optimum mechanical properties and compaction behavior were observed for the 3${\mu}$m alumina particle dispersed composite. The 3${\mu}$m alumina particle size and distribution for he preform were within 0.1 to 48${\mu}$m and bimodal and random orientation. The strength and the fracture toughness of the composite having 3${\mu}$m alumina particles were 519MPa and $4.5MPa{\cdot}m^{1/2}$, respectively.

• Journal of Life Science
• /
• v.27 no.9
• /
• pp.1086-1095
• /
• 2017

There is growing interest in groundwater resources to overcome the loss of surface water resources due to climate change. An understanding of the microbial community of aquifers is essential for monitoring and evaluating groundwater contamination, as well as groundwater management. Most microorganisms that inhabit aquifer ecosystems are attached to sediment particles rather than planktonic, as is the case in groundwater. Since sampling aquifer sediment is not easy, groundwater, which contains planktonic microorganisms, is generally sampled in microbial community research. Although many studies have investigated microbial communities in contaminated aquifers, there are only a few reports of microbial communities in uncontaminated or pristine aquifers, resulting in limited information on aquifer microbial diversity. Such information is needed for groundwater quality improvement. This paper describes the ecology and community structure of groundwater bacteria in uncontaminated aquifers. The diversity and structures of microbial communities in these aquifers were affected by the concentration or distribution of substrates (e.g., minerals, organic matter, etc), in addition to groundwater characteristics and human activities. Most of the microbial communities in these uncontaminated aquifers were dominated by Proteobacteria. Studies of microbial communities in uncontaminated aquifers are important to better understand the biogeochemical processes associated with groundwater quality improvement. In addition, information on the microbial communities of aquifers can be used as a basis to monitor changes in community structure due to contamination.

• Journal of the Mineralogical Society of Korea
• /
• v.20 no.2 s.52
• /
• pp.71-81
• /
• 2007

The marble-type dolomite from the Jasung Mine, which was farmed by duplicated affects of contact metamorphism and subsequent hydrothermal alteration, corresponds to a high-purity dolomite ranging up to above 98wt.% in dolomite contents. The dolomite contain minor impurities such as quartz, muscovite, and pyrite. It is characteristic that the dolomite is fairy Fe-rich corresponding to 0.4 wt.% due to the presence of pyrite of possible hydrothermal origin. The dolomite is nearly white-colored and constituting with subhedral crystals ranging $0.35{\sim}0.46mm$M in size, forming equigranular texture. Compared to the typical high-Ca limestone from the Pungchon Formation, the powder characteristics of dolomite is rather superior in milling efficiency, yields of fine particles, and size distribution. In addition, except for iron contents, the dolomite powder is no less superior than the limestone in quality and characteristics as fillers with respects to not only whiteness, oil absorption, and specific surface area but also shape characters such as elongation ratio, aspect ratio, and sphericity. This good characteristics of dolomite powder seem to be originated basically from comparatively higher grade and crystallinity of dolomite. Higher iron contents and the presence of sulfides prevents the dolomite from application for uses by thermal treatment, except for metallic manufacture. However, if proper ore separation procedure is available, the dolomite can be sufficiently utilized as substitutes for high-Ca limestone in most fields of filler industries.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.38 no.8
• /
• pp.1076-1083
• /
• 2009

The physicochemical properties of rice flour produced by 3 different grinding methods using various steeping times (3, 6, 9, and 12 hrs) were investigated. Roller mill gave coarse rice flour; the pin mill, intermediate flour; and mixed when both (roller & pin mills) were used. With the increase of steeping times, the rice flours became finer and the contents of crude protein, crude fat and crude ash decreased. Damaged starch was noticeably high in rice flour by roller & pin mills compared to those by roller or pin mills alone. Amylose contents, solubility and swelling power increased as the steeping times increased. Water binding capacity was the highest in roller & pin mills, followed by pin mill. In scanning electron microscope (SEM), pin mill showed distribution of separated fine particles of rice flours. The physicochemical properties of rice flours showed many differences by steeping times of rice and grinding methods. With sufficient steeping times, the rice flours obtained from pin mill were relatively fine having less damaged starch.

• Korean Journal of Mineralogy and Petrology
• /
• v.33 no.1
• /
• pp.19-28
• /
• 2020

Ranciéte is a hexagonal phyllomanganate mineral containing random Mn(IV) vacancies with hydrated Ca²⁺ cations charged balanced as interlayer cations. Its Mn²⁺ analogue is called takanelite, and ranciéite and takanelite are regarded as end-members of a solid solution series of (Ca²⁺,Mn²⁺)Mn₄O₉·nH₂O. Because the minerals are found as very small particles associated with other minerals, the crystal structures of the solid solution series have yet to be defined. In this research, we conducted classical molecular dynamics (MD) simulations of ranciéite and takanelite by varying the Mn²⁺/Ca²⁺ interlayer cation ratio to find relations between the interlayer cations and mineral structures. MD simulation results of chalcophanite group minerals are compared with experimental results to verify our method applied. Then, lattice parameters of ranciéite and takanelite models are presented along with detailed interlayer structures as to the distribution and coordination of cations and water molecules. This study shows the potentials of MD simulations in entangling complicated phyllomanganates structures.

• Nuclear Engineering and Technology
• /
• v.38 no.2
• /
• pp.163-174
• /
• 2006

The $Ph{\acute{e}}bus$ FP project is an international reactor safety project. Its main objective is to study the release, transport and retention of fission products in a severe accident of a light water reactor (LWR). The FPT4 test was performed with a fuel debris bed geometry, to look at late phase core degradation and the releases of low volatile fission products and actinides. Post Test Analyses results indicate that releases of noble gases (Xe, Kr) and high-volatile fission products (Cs, I) were nearly complete and comparable to those obtained during $Ph{\acute{e}}bus$ tests performed with a fuel bundle geometry (FPT1, FPT2). Volatile fission products such as Mo, Te, Rb, Sb were released significantly as in previous tests. Ba integral release was greater than that observed during FPT1. Release of Ru was comparable to that observed during FPT1 and FPT2. As in other $Ph{\acute{e}}bus$ tests, the Ru distribution suggests Ru volatilization followed by fast redeposition in the fuelled section. The similar release fraction for all lanthanides and fuel elements suggests the released fuel particles deposited onto the plenum surfaces. A blockage by molten material induced a steam by-pass which may explain some of the low releases. The revaporisation testing under different atmospheres (pure steam, $H_2/N_2$ and steam /$H_2$) and up to $1000^{\circ}C$ was performed on samples from the first upper plenum. These showed high releases of Cs for all the atmospheres tested. However, different kinetics of revaporisation were observed depending on the gas composition and temperature. Besides Cs, significant revaporisations of other elements were observed: e.g. Ag under reducing conditions, Cd and Sn in steam-containing atmospheres. Revaporisation of small amounts of fuel was also observed in pure steam atmosphere.

• Journal of the Korean Electrochemical Society
• /
• v.6 no.4
• /
• pp.266-270
• /
• 2003

The $LiN_{0.8}Co_{0.2}O_2$ has shown outstanding electrochemical properties. The microstructure of $LiN_{0.8}Co_{0.2}O_2$ cathode was investigated by using TEM (transmission electron microscopy) and X-ray diffraction techniques. The $LiN_{0.8}Co_{0.2}O_2$ was produced by sol-gel method to synthesize fine particles less than $1{\mu}m$ in the average diameter. In this study, emphasis was given to the examination and interpretation of the microstructural change during charge-discharge cycling experiments, which appeared to be one of the main causes of early degradation of rechargeable batteries. Results showed that the $1{\mu}m$ cathode produced by sol-gel method had high reversible capacity and excellent cycling stability due to its homogeneous distribution of Ni and Co cations on u atomic scale. In particular, the $1{\mu}m$ cathode did not show severe strain induced structural defects or cubic spinel disordering during cycling experiments, which had been observed in the conventional $LiCoO_2$ cathode. The $LiNi_{0.8}Co_{0.2-x}M_x[M=Al]$ compounds show good reversibility but low discharge capacity.

• Korean Journal of Food Science and Technology
• /
• v.28 no.6
• /
• pp.1078-1083
• /
• 1996

During the pearling process of hull-less barley, protein, lipid, ash and insoluble dietary fiber (IDF) contents decreased, while soluble dietary fiber (SDF) and ${\beta}-glucan$ contents slightly increased. Depending on milling methods and types of grinding mills used, there were differences in particle size distribution of barley flour. Flour particle size was smaller in the following order of Fitz mill, Ball mill, Pin mill, Cyclotec sample mill and Jet mill. Color (brightness) was closely related to the particle size of barley flour. Damaged starch (%) in pearled barley flour was the highest in Jet mill among different mills. Flours prepared with Cyclone mill and Pin mill had a reasonable amount of damaged starch. Flour produced by Fitz mill showed the lowest amount of damaged starch. Scanning electron microscopy (SEM) of the flour samples demonstrated different sizes and shapes of particles consisting of starch granules and cell wall materials. Damaged starch tended to increase water absorption index (WAI), water solubility index (WSI), and water retention capacity (WRC). Pasting viscosity determined by amylograph was relatively high in Pin-milled and Cyclone-milled flours. Viscosity was the lowest in coarsely ground flour by Fits mill.