• 한국공간구조학회논문집
• /
• 제11권2호
• /
• pp.139-149
• /
• 2011

케이블 구조물은 비교적 가볍고 넓은 공간의 형성이 쉬우나 유연한 특징으로 인해 형상의 제어가 매우 민감하다. 이런 구조물은 여러 이유에서 형상의 보정이 필요하며, 특히 부재 제어량과 어떠한 부재를 제어해야 하는가는 것은 많은 연구자들이 고심하고 있는 문제이다. 따라서 본 논문의 목적은 하중법(Force Method)를 이용해서 형상조절을 위한 변위 제어기법을 연구하는 것이다. 논문은 2장에서는 제어 방정식을 설명하고, 3장에서는 단순 케이블 넷 모델을 이용하여 동시 및 순차제어를 고려해 해석을 수행하고 결과를 고찰한다. 4장에서는 보다 더 복잡한 케이블 돔 구조물에 적용하여 가장 유용한 부재에 대해서 논의 하고, 5장에서 결과를 요약한다.

• 한국인터넷방송통신학회논문지
• /
• 제10권5호
• /
• pp.31-37
• /
• 2010

본 논문은 홈 케어를 위해 생체 센서 시스템으로 홈 네트워크 시스템을 구성하여 생체 신호가 전달되도록 생체 신호 알고리즘을 구현하였다. 알고리즘의 구성 조건은 입력함수, 주파수 변화 함수, 변위 점 산출 발생 함수, 위치 변동 축 발생 함수, 축 변화 흔들림 변위(Sway Displacement)의 함수에서 변위치의 최대 값과 최소 값을 기준에 조정할 수 있는 단계로 주파수 변동이 0.01 단위로 변화가 있도록 조정하였다. 산출되는 항목은 맥박(Heart Rate), 체온(Temperature), 체중(Weight) 로 구성되고, 파형으로 신체적 균형정도를 확인하고 건강의 상태를 확인하도록 의미를 부여하였다. 본연구의 결과로 홈 네트워크를 통해 헬스 센터 및 건강관리 중앙 시스템에 단말기를 통해 전송된 알고리즘으로 홈 내 건강 관리시스템이 진행되는 결과를 얻을 수 있고, 다양한 신체적 파라메타를 통한 모니터링 기능을 갖춘 시스템관리가 형성 될 것으로 예상된다.

• 한국구조물진단유지관리공학회 논문집
• /
• 제13권2호통권54호
• /
• pp.129-136
• /
• 2009

이 연구에서는 사장교의 시공 중 장력보정을 위한 최적 변위계측 위치(OLD) 결정법을 제안한다. 변위 민감도를 구하여 Fisher Information Matrix(FIM)를 정식화하였고, 이를 이용한 유효독립분포벡터(EIDV)를 계산하여 최적 변위계측 위치의 우선순위를 결정하였다. 결정된 최적 변위계측 위치의 효율성과 신뢰성을 검증하기 위하여 사장교에 대한 수치예제를 수행하였다. 변위를 사용한 FIM을 정식화하여 이의 결과를 변위 민감도를 사용한 결과와 수치예제를 통해 비교하였다. 또한 변위 측정오차와 케이블 길이오차가 장력 보정에 미치는 영향을 Monte Carlo 기법을 사용하여 통계적으로 분석하였다.

• 대한원격탐사학회지
• /
• 제35권1호
• /
• pp.29-37
• /
• 2019

Synthetic Aperture Radar (SAR) observations are powerful tools to monitor surface's displacement very accurately, induced by earthquake, volcano, ground subsidence, glacier movement, etc. Especially, radar interferometry (InSAR) which utilizes phase information related to distance from sensor to target, can generate displacement map in line-of-sight direction with accuracy of a few cm or mm. Due to decorrelation effect, however, degradation of coherence in the InSAR application often prohibit from construction of differential interferogram. Offset tracking method is an alternative approach to make a two-dimensional displacement map using intensity information instead of the phase. However, there is limitation in that the offset tracking requires very intensive computation power and time. In this paper, efficiency of parallel computing has been investigated using high performance computer for estimation of glacier velocity. Two TanDEM-X SAR observations which were acquired on September 15, 2013 and September 26, 2013 over the Narsap Sermia in Southwestern Greenland were collected. Atotal of 56 of 2.4 GHz Intel Xeon processors(28 physical processors with hyperthreading) by operating with linux environment were utilized. The Gamma software was used for application of offset tracking by adjustment of the number of processors for the OpenMP parallel computing. The processing times of the offset tracking at the 256 by 256 pixels of window patch size at single and 56 cores are; 26,344 sec and 2,055 sec, respectively. It is impressive that the processing time could be reduced significantly about thirteen times (12.81) at the 56 cores usage. However, the parallel computing using all the processors prevent other background operations or functions. Except the offset tracking processing, optimum number of processors need to be evaluated for computing efficiency.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2010년도 추계학술대회 초록집
• /
• pp.171-171
• /
• 2010

An innovative design of a floating-buoy wave energy converter (WEC) using hydrostatic transmission (HST), named HSTWEC, is presented in this paper. The system is designed to convert ocean wave fluctuation into electricity by using the HST circuit and an electric generator. Based on the floating-buoy concept, the wave forces the sub-buoy to move up and down. Consequently, the electric power can be obtained from the generator in both the moving directions of the sub-buoy through the HST circuit as shown in Fig. 1. In order to investigate the HSTWEC operations, a mathematical model of the system is indispensible. In addition, the method to control the HSTWEC, including: pump displacement control, tension adjustment control and ballast weight control, is also discussed in this paper. Finally, the design concept as well as simulation results indicated that this HSTWEC design is an effective solution and possible to fabricate for wave energy generation.

• 한국공간구조학회논문집
• /
• 제20권3호
• /
• pp.43-52
• /
• 2020

In this study, the Buckling restrained braces reinforced with engineering plastics that can compensate for the disadvantages in the manufacturing process of the existing buckling restrained brace. The proposed PC-BRB was fabricated to evaluate the reinforcement effect by carrying out a structural performance test and a full-scale two-layer frame test through cyclic loading test. As a result of PC-BRB's incremental and cyclic loading test, stable hysteresis behavior was achieved within the target displacement, and the compressive strength adjustment coefficient satisfied the recommendation. As a result of the real frame experiment, the strength of the reinforced specimen increased compared to the unreinforced specimen, and the ductility and energy dissipation increased.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2003년도 가을 학술발표회 논문집
• /
• pp.367-370
• /
• 2003

This study was carried out to suggest the effective reinforcing method which can evaluate the tensile capacity of cast-in-place anchor with cracks. Currently, cast-in-place anchor is used widely for the fastening of equipment in Korean NPPs. 26 test specimens with a single anchor under 4 cracked conditions are prepared using plain concrete. The distance between crack and anchor and reinforcing materials were selected as the main test variable. The tensile force was applied using a actuator with a capacity of 100 tonf using a displacement control method of 0.5 mm/min velocity. Test results from this result show the combination of carbon plate and epoxy will be more available for repair and reinforcement of equipment foundation system in NPPs. Further experimental work is indeed involving the epoxy injection effect and adjustment of reinforcing location of carbon sheet.

• 대한기계학회논문집
• /
• 제18권6호
• /
• pp.1374-1381
• /
• 1994

This study suggests a new type shaft generating system driven by hydrostatic transmission suitable for small size vessels. In this system, the hydraulic motor speed is controlled by displacement adjustment using a 3-way high speed on/off valve. The 3-way high speed valve is operated by PWM control signal. In this study, a digital robust servo control algorithm is applied to the controller design of the system. By experiments and numerical computations, the frequency variation characteristics of the generating system under various disturbances are investigated. Conclusively, it is said that the shaft generating system proposed in this study shows excellent control performances.

• 대한조선학회논문집
• /
• 제48권6호
• /
• pp.528-538
• /
• 2011

As a forming method for curved hull plates more efficient than the flame bending, mechanical bending using multi point press forming and die-less forming is discussed in this paper. the mechanical forming is a flexible manufacturing system for automatically forming of hull parts. It is especially suited to varied curved parts. This paper discusses a multiple point pressing machine composed of a pair of reconfigurable punches in order to achieve the rapid forming of curved hull plates using division forming and presents how forming information is obtained from the given design surface. Although the mechanical forming can be efficient in the metal forming, spring back after pressing is a phenomenon which must be carefully considered when quantifying the process variables. If the spring back is not accurately controlled, the fabricated shell plate cannot meet assembly tolerance. This paper describes the principles to calculate the proper stroke of each punch at the divided areas. the strokes are determined by an iterative process of sequential pressing and spring back compensation from an unfolded flat shape to its given design surface. FEA(finite element analysis) is used to simulate the spring back of the plate and the IDA(iterative displacement adjustment) method adjusts the offset of pressing punches from the deformation results and the design surface. The shape deviations of two surfaces due to spring back are compensated by integrated system using FEA and IDA method. For the practical application, It is aimed to develop an integrated system that can automatically perform the compensation process and calculate strokes of punches of the double sides' reconfigurable multiple-press machine and some experimental results obtained with mechanical bending are presented.

• 한국산학기술학회논문지
• /
• 제16권12호
• /
• pp.8274-8283
• /
• 2015

텔레비전의 가스 스프링은 롱 스트로크 (200 ~ 300mm, TV 상승 변위) 하에서 작동 할 때 피스톤 속도의 제어가 가능하다. 이 원리에 의해서 사용자는 높낮이 조절이 가능하다. 먼저 피스톤의 흐름 해석을 수행하였다. 정확한 관형 단면을 위한 피스톤 속도 조절기술을 조사하였다. 유동률 제어 및 높낮이 작용을 위한 피스톤 구조를 제안되었다. 본 연구는 대형 텔레비전 스탠드를 통해 50 인치 이상 TV의 가스 스프링의 개발을 위한 것이다. 최적 피스톤 로드 제어를 위한 중공축(외경 19.9mm, 내경 13.9mm)에 질소 개스(0.3m/s)를 주입하였다. 그 결과, 유동율이 증대함에 따라 피스톤 로드의 압력강하는 외력의 변화 없이 증대되었다. 결과적으로, 가스스프링을 통한 변위의 제어는 가능하다.