• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2000.11a
• /
• pp.147-152
• /
• 2000

This paper presents the thermoelastic analysis and 3-D failure analysis of the carbon/carbon brake disk. The mechanical properties of the carbon/carbon brake disk were measured for both in-plane and out of plane directions. The mechanical properties were used as the input of the thermoelastic analysis and 3-D stress analysis for the brake disk. The gap between rotor clip and clip retainer was an important parameter in the loading transfer mechanism of the rotor. The change of gap was considered separating the mechanical deformation and thermal deformation. Because the rotor clip and clip retainers were not contacted, the clip retainers and rivets were excluded from the rotor analysis model. The disk was modeled by using the cyclic symmetry condition and the contact problem between the rotor disk and rotor clip was considered. From the results of the 3-D stress analysis, the stress concentration at the key hole of the brake disk was confirmed.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.16 no.6
• /
• pp.125-132
• /
• 2007

Inherent dynamic interaction between flexible disk and workpiece creates partially non-flat surface profile. A flat zone was defined using minimum depth of engagement. Several key parameters were defined to explain the characteristics of the zone. Process conditions including disk rotation speed, initial depth of cut and feed speed were varied to produce product profile database. Correlation between key factors was examined to find the characteristic dependencies. Trends of key parameters were displayed and explained. Higher flat zone ratio was observed for lower depth of cut and higher disk rotation speed. Ratio of minimum depth of cut against target depth of cut increased for higher feed speed and disk rotation speed but was insensitive to the depth of cut variation. The process transition was visualized by continuously displaying instantaneous orientation of the deflected disk and the location of key parameters were clearly marked for comparison.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.4 no.3
• /
• pp.233-241
• /
• 1992

Temperature distributions in a 3.5 inch hard disk drive including disk surface and internal air have been simulated numerically. Solutions were obtained from fifteen cases regarding three power consumption rates and five ambient conditions. As a result, the velocity of cooling air should be maintained greater than ㏐/s when the power consumption reached 3W in the disk drive. A correlation equation was proposed to predict the temperature field of disk surface and caseing surface.

• Tribology and Lubricants
• /
• v.16 no.5
• /
• pp.395-402
• /
• 2000

The effect of particulate contamination on friction and wear between a negative-pressure picoslider and a laser-textured disk was studied. Particles of different concentrations, materials and sizes were injected to the head-disk interface (HDI), consisting of disks with various textures, at the same speed. In a contaminated environment, durability of head-disk interface gradually decreased as the particle concentration increased. Large particles caused HDI failure early and resulted in an extensive damage to the slider and disk surfaces. Hard particles also caused HDI failure earlier and damages more extensive than soft ones. Based on the test results, mechanisms of HDI failure with picoslider were presented.

• Journal of the Korean Society for Precision Engineering
• /
• v.21 no.5
• /
• pp.122-130
• /
• 2004

In a high-speed and wide operating field optical disk drive, the vibration problem is one of the most important factors to be considered for reliable performance. And a disk misaligned with axis of rotation is a major source of vibration in optical disk drive. Furthermore, this vibration disturbance of the disk spindle system causes failure in the reading and writing process. So to solve this vibration problem, the vibration absorber using rubber mount has been introduced in recent years. In this paper, we have analyzed the simple optical disk drive model with dynamic vibration absorber through dynamic analysis of 12-dof by Recurdyn program and obtained optimal mass and frequency ratios of dynamic vibration absorber of dynamic vibration absorber and the optimal frequency ratio.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2000.11a
• /
• pp.784-789
• /
• 2000

Equations of motion are derived and solved using the finite element method substructure synthesis for the disk-spindle system with rigid spindle and flexible shaft. The disk is modeled as a flexible spinning disk by Kirchhoff plate theory and von Karman nonlinear strain. The spindle supporting the flexible disk is modeled as a rigid body to consider its complex geometry. The stationary shaft supporting the rotating disk-spindle-bearing system is modeled by Euler beam, and the ball bearings are modeled as the stiffness matrix with 5 degrees of freedom. Developed theory is applied to analyze the vibration characteristics of a 3.5" HDD and a 2.5" HDD, respectively, and modal tests are performed to verify the simulation results. This paper shows that the developed theory can be effectively applied to the rotating disk-spindle system with the spindle of complex shape.

• Journal of the Korean Society of Industry Convergence
• /
• v.3 no.4
• /
• pp.353-360
• /
• 2000

The purpose of this research is to find the fundamental data for the design and optimum operation condition for the disk atomization comparing the atomization characteristics of the modified straight vane type disk atomizer and the cup type atomizer widely used in the field of spray dry. First, the experimental comparison of the characteristics of $Na_2SO_4$ atomization has been carried out using the cup type disk atomizer and the three kinds of vane type atomization designed specially for the experiment. After the comparison of the experimental data of the $Na_2SO_4$ and raw milk have been conducted using vane type atomizer.

• Proceedings of the KSR Conference
• /
• 2008.11b
• /
• pp.1761-1765
• /
• 2008

In the braking of a railroad car, mechanical brake systems using wheel tread and brake disk are applied as well as electrical brake systems by regenerator and rheostat. It is very important to consider the frictional characteristic because kinetic energy of the vehicle is dissipated as converted thermal energy through friction between disk and brake pad during disk braking. A friction coefficient and wear characteristic are decided from the interrelationship of disk and friction material in the disk brake system. Lab-scale dynamometer test on developed brake disk materials for increasing heat resistance was performed in this study. Each candidate material was tested at various braking speeds and pressures and we obtained the friction coefficient and wear characteristic. And we executed comparative evaluation of the result from the test.

• Journal of the Korean Society of Visualization
• /
• v.19 no.1
• /
• pp.88-93
• /
• 2021

For a flow normal to a circular disk, the flow separation occurs from the edge of the disk and the flow recirculation zone exists behind the disk. Many existing studies conducted simulations of flow normal to a circular disk under low Reynolds numbers. Some studies performed LES or DES simulations under high Reynolds numbers. However, comparative study for different RANS models for high Reynolds numbers is very limited. This study presents numerical simulations of a flow normal to a circular disk using Realizable k-ε model and SST k-ω model. The recirculation bubble length and drag coefficient were compared with the experimental data. The SST k-ω model showed the excellent predictions for the recirculation bubble length and drag coefficient.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.11a
• /
• pp.340.2-340
• /
• 2002

A practical implementation method of squeeze-film aeroelastic disk vibration damping and its practical design performance are presented to provide a solution method to meet the tight TMR(Track Mis-Registration) design budget of high-TPI HDDs. Most previous research results are mainly based on the component-level study in the 'open-cover state' which is far from the realistic operations HDD condition. (omitted)