• 한국의상디자인학회지
• /
• 제15권3호
• /
• pp.33-40
• /
• 2013

This paper focused on investigating the seam strength by cutting direction depending on the fabrics and weave by comparing the tensile strength and elongation of bias, warp and weft of 4 kinds of find cotton fabrics and combining 6 kinds of seam cutting directions. The cutting directions are selected the warp direction, weft direction and 45-degree bias direction. Then, three kinds of directions, the warp/warp direction, the weft/weft direction and the bias/bias directions, and the three different kinds of directions, the warp/weft direction, the warp/bias direction and the weft/bias directions, were finally selected. The results are as follows: The tensile strength of all fabrics was higher in the order of warp, bias and weft direction and tensile elongation was higher in the order of bias, warp and weft direction in almost all fabrics. 100's and 150's cotton fabrics showed the highest seam strength when they were cut in the bias/bias direction. The seam strength of the fabrics cut in the same direction was the highest in the fabrics cut in the bias/bias direction. Four kinds of fabrics demonstrated the similar seam strength. However, for the seam strength of fabrics cut in the different directions, 100's cotton fabrics had the difference of seam strength by direction and weave, but 150's cotton fabrics didn't have any difference in seam strength by direction and weave. As described above, the seam strength was influenced by the cutting direction of fabrics. Accordingly, the seam strength can be improved by changing the cutting direction of seam when making the clothing.

• Journal of Mechanical Science and Technology
• /
• 제14권8호
• /
• pp.891-899
• /
• 2000

The flame speed may be decomposed into the burning speed and the flame transport speed. The flame transport speed is affected considerably by the flow direction, variation rate of flow direction, and flow speed in the combustion chamber. Especially, the flow direction and the variation rate of flow direction at the spark plug location during the ignition period have an important effect on the ignition process and the early flame propagation process. We measured the flow direction component and the variation rate of flow direction with a hot wire probe at the spark plug location. It was shown that the representative flow direction of ignition period is the right-vertical direction of crank shaft and it was used to investigate the variation rate of flow direction.

• 대한인간공학회지
• /
• 제34권1호
• /
• pp.75-83
• /
• 2015

Objective: The aim of this study is to suggest the standard of the direction sign on the pendant switch of overhead cranes which can reduce human errors in control. Background: A great number of crane accidents occur in industries. One of the major causes of the accidents is the mistake in the control of cranes by confusing the orientation of crane movements. Nevertheless, three different direction sign styles, 'East, West, South, North (EWSN)', 'Forward, Backward, Left, Right (FBLR)', and arrows for four directions are used without standardization. Method: An overhead crane simulator was installed for a laboratory experiment. It could move along six directions by the control of a pendant switch. 90 participants were evenly assigned to the three different conditions of direction sign styles. The participants were asked to control the pendant switch according to the continuously appearing 16 direction signs on a monitor ahead. The participants were allowed to refer an orientation sign board on the ceiling representing correct movement directions of the overhead crane simulator. Results: The direction sign style, 'EWSN', showed statistically significant better performance in task completion time and number of errors than the other sign styles. The direction sign style, 'EWSN', adopting the cardinal direction system, made the participants clear in direction controls after customizing to the crane movements. However, the direction sign styles, 'FBLR' and the arrows adopting the relative direction system made conflicts in direction controls due to the egocentric view of human. Conclusion: The direction sign style, 'EWSN', is the most appropriate for the standardization of the direction sign on the pendant switch of overhead cranes. Application: The results of this study can be applied to the standardization of direction sign in the legal notification on the safety certifications of crane manufacturing.

• 한국공간구조학회논문집
• /
• 제8권3호
• /
• pp.75-82
• /
• 2008

본 연구에서는 방향벡터(direction vector)를 이용한 지역 탐색법과 유전자 알고리즘을 결합한 새로운 알고리즘인 D-GA를 제안한다. 새로운 개체(individual)를 찾기 위한 방향벡터로는 진화과정 중에 습득되는 정보를 활용하기 위한 학습방향벡터(Loaming direction vector)와 진화와는 무관하게 한 개체의 주변을 탐색하는 랜덤방향벡터(random direction vector) 등 두 가지를 구성하였다. 그리고, 10 부재 트러스 설계 문제에 단순 유전자 알고리즘과 D-GA를 적용하여 최적화를 수행하였고, 그 결과를 비교 검토함으로써 단순 GA에 비하여 D-GA의 정확성 및 효율성이 향상되었음을 확인하였다.

• 한국군사과학기술학회지
• /
• 제23권1호
• /
• pp.52-58
• /
• 2020

In this paper, a 2-dimensional phase comparison direction finding receiver was designed and fabricated. For 2-D comparison direction finding, direction finding formulas were derived from a uniformly arranged of four antennas. Based on this, a direction finding receiver was designed using Matlab simulink, and the direction finding receiver was fabricated. To analyze the performance of the designed direction finding receiver, the injection direction finding accuracy and simulation results were compared. As a result of the test, the fabricated direction finding receiver showed a maximum of 3° RMS precision, and the result of both tests showed similar trends. Also, it was confirmed that the direction finding accuracy of elevation angle is about 2.7 times better than azimuth angle, and both models performed well within 0.7° RMS at the boresight.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2004년도 추계학술발표대회 논문집
• /
• pp.272-277
• /
• 2004

The elastic waves in the plate are dispersive waves with the characteristics of Lamb waves. However, $S_0$ symmetric mode is less dispersive in the frequency region less than first cut-off frequency. And, in anisotropic plates such as CFRP plates, the propagation velocities vary with the direction. So, the wave vector direction to be the phase velocity direction is not accord with the energy flow direction to be the group velocity direction. In this work, the group velocities of the $S_0$ symmetric mode less than the first cut-off frequency was analyzed with the group velocity dispersion curves in unidirectional CFRP plate. And, the group velocity curve obtained by the group velocity dispersion curves are compared with the measured velocities as varied the propagation direction of the Lamb wave. The measured velocities are good agreement with the corrected group velocity curve except near the fiber direction which is called the cusp region. When the propagation direction is not accorded with the principal axis, the direction of the group velocities declines to the fiber direction in the unidirectional CFRP plates. This implies that the energy propagates preferentially toward fiber direction.

• 융합신호처리학회논문지
• /
• 제5권2호
• /
• pp.119-125
• /
• 2004

방향 성분은 소벨(sobel)과 FFT 방법 등을 주로 사용한다. 소벨을 이용한 방법은 소벨 마스크의 복잡한 처리 과정과 대표 방향 성분을 추출하고자 할 때 픽셀별로 단위 벡터를 만들어 누적시킬 경우 낮은 대비 영상이나 높은 대비 영상이나 같은 값이 나오므로 기울기 크기를 누적할 수 없어 대표 방향을 설정하기 어렵다. FFT를 변환을 이용한 방법은 융선이 정확한 방향 성분을 가지는 경우에만 방향성 추출이 가능하며 별도의 방향 필터를 사용해야 한다. 본 논문에서는 위의 단점을 보완하기 위하여 이진화 된 영상을 세선화 한 후 픽셀 단위로 방향 성분을 추출하며, 8${\times}$8 픽셀크기의 블록 내에 존재하는 픽셀이 가지는 방향 성분 중 가장 많은 방향 성분을 융선의 대표 방향으로 추출하는 새로운 방법을 제안한다.

• 대한치과기공학회지
• /
• 제7권1호
• /
• pp.5-12
• /
• 1985

This experimental study is perform to study the effect of the direction for the centrifugal force in operating centrifugal casting machine. In order to investigate the effect of direction for centrifugal force action on the casting ability 20 pieces of specimen are produced including one vertical direction and four horizontal directions. Casting shows us that the 15 pieces of specimen among them are included within $\pm$16. The results obtained through the comparison with 5 groups of the casting ability are as follows: 1. In the experiment of the casting, statistically significant difference are found between the vertical direction and the group of horizontal direction, namely, the direction of 3, 6, 9 and 12 o'clock, and also statistically there are significant differences between the direction of 9 o'clock and of 6 o'clock, and between the direction of 9 o'clock and of 12 o'clock which lie between the groups of horizontal directions. 2. The degree of casting ability is showing us on an average, 23.80 in the vertical direction. And also in the group of horizontal direction it prove in turn 15.60 in the direction of 9 o'clock, 14.47 of 3 o'clock, 13.30 of 12 o'clock, and 12.80 of 6 o'clock.

• Journal of information and communication convergence engineering
• /
• 제8권1호
• /
• pp.29-34
• /
• 2010

Wind speed and wind direction are usually taken using two parameters: wind speed and wind direction. This paper studies the average wind speed and direction calculation methods. The paper first introduces to basic wind's knowledge, and then presents several methods in calculating average wind speed and direction. Lastly some graphs are plotted base on these computational methods and the implementation of these methods in an actual buoy system.

• Journal of Electrical Engineering and Technology
• /
• 제1권4호
• /
• pp.423-426
• /
• 2006

Distance relays achieve selective tripping by measurement of all short circuit fault conditions inside set reaches. The direction of the fault, forward or reverse is commonly determined with a dedicated measurement to ensure selectivity under all conditions. For the direction decision (measurement) a number of alternatives are available. This paper describes a loop selective direction measurement and illustrates by means of a typical fault why this is superior to a non loop selective direction measurement such as that based on negative sequence quantities.