• Geomechanics and Engineering
• /
• v.16 no.2
• /
• pp.205-215
• /
• 2018

Strain-based criteria are known as a direct method in determining the stability of the geomechanical structures. In spite of the widely use of Sakurai critical strain criterion, it is so conservative to make use of them in rocks with initial plastic deformation on account of the considerable difference between the failure and critical strains. In this study, a new criterion has been developed on the basis of the failure strain to attain more reasonable results in determining the stability status of the tunnels excavated in the rocks mostly characterized by plastic-elastic/plastic behavior. Firstly, the stress-strain curve was obtained having conducted uniaxial compression strength tests on 91 samples of eight rock types. Then, the initial plastic deformation was omitted making use of axis translation technique and the criterion was presented allowing for the modified secant modulus and by use of the failure strain. The results depicted that the use of failure strain criterion in such rocks not only decreases the conservativeness of the critical strain criterion up to 42%, but also it determines the stability status of the tunnel more accurately.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.196-197
• /
• 2010

NAND형 charge trap flash (CTF) non-volatile memory (NVM) 소자가 30nm node 이하로 고집적화 되면서, 기존의 SONOS형 CTF NVM의 tunnel barrier로 쓰이는 SiO2는 direct tunneling과 stress induced leakage current (SILC)등의 효과로 인해 data retention의 감소 등 물리적인 한계에 이르렀다. 이에 따라 개선된 retention과 빠른 쓰기/지우기 속도를 만족시키기 위해서 tunnel barrier engineering (TBE)가 제안되었다. TBE NVM은 tunnel layer의 전위장벽을 엔지니어드함으로써 낮은 전압에서 전계의 민감도를 향상 시켜 동일한 두께의 단일 SiO2 터널베리어 보다 빠른 쓰기/지우기 속도를 확보할 수 있다. 또한 최근에 각광받는 high-k 물질을 TBE NVM에 적용시키는 연구가 활발히 진행 중이다. 본 연구에서는 Si3N4와 HfAlO (HfO2 : Al2O3 = 1:3)을 적층시켜 staggered의 새로운 구조의 tunnel barrier Capacitor를 제작하여 전기적 특성을 후속 열처리 온도와 방법에 따라 평가하였다. 실험은 n-type Si (100) wafer를 RCA 클리닝 실시한 후 Low pressure chemical vapor deposition (LPCVD)를 이용하여 Si3N4 3 nm 증착 후, Atomic layer deposition (ALD)를 이용하여 HfAlO를 3 nm 증착하였다. 게이트 전극은 e-beam evaporation을 이용하여 Al를 150 nm 증착하였다. 후속 열처리는 수소가 2% 함유된 질소 분위기에서 $300^{\circ}C$와 $450^{\circ}C$에서 Forming gas annealing (FGA) 실시하였고 질소 분위기에서 $600^{\circ}C{\sim}1000^{\circ}C$까지 Rapid thermal annealing (RTA)을 각각 실시하였다. 전기적 특성 분석은 후속 열처리 공정의 온도와 열처리 방법에 따라 Current-voltage와 Capacitance-voltage 특성을 조사하였다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.27-27
• /
• 2011

For the design of real applicable molecular devices, current-voltage properties through molecular nanostructures such as metal-molecule-metal junctions (molecular junctions) have been studied extensively. In thiolate monolayers on the gold electrode, the chemical bonding of sulfur to gold and the van der Waals interactions between the alkyl chains of neighboring molecules are important factors in the formation of well-defined monolayers and in the control of the electron transport rate. Charge transport through the molecular junctions depends significantly on the energy levels of molecules relative to the Fermi levels of the contacts and the electronic structure of the molecule. It is important to understand the interfacial electron transport in accordance with the increased film thickness of alkyl chains that are known as an insulating layer, but are required for molecular device fabrication. Thiol-tethered RuII terpyridine complexes were synthesized for a voltage-driven molecular switch and used to understand the switch-on mechanism of the molecular switches of single metal complexes in the solid-state molecular junction in a vacuum. Electrochemical voltammetry and current-voltage (I-V) characteristics are measured to elucidate electron transport processes in the bistable conducting states of single molecular junctions of a molecular switch, Ru(II) terpyridine complexes. (1) On the basis of the Ru-centered electrochemical reaction data, the electron transport rate increases in the mixed self-assembled monolayer (SAM) of Ru(II) terpyridine complexes, indicating strong electronic coupling between the redox center and the substrate, along the molecules. (2) In a low-conducting state before switch-on, I-V characteristics are fitted to a direct tunneling model, and the estimated tunneling decay constant across the Ru(II) terpyridine complex is found to be smaller than that of alkanethiol. (3) The threshold voltages for the switch-on from low- to high-conducting states are identical, corresponding to the electron affinity of the molecules. (4) A high-conducting state after switch-on remains in the reverse voltage sweep, and a linear relationship of the current to the voltage is obtained. These results reveal electron transport paths via the redox centers of the Ru(II) terpyridine complexes, a molecular switch.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.104-104
• /
• 2009

Critical dimensions has rapidly shrunk to increase the degree of integration and to reduce the power consumption. However, it is accompanied with several problems like direct tunneling through the gate insulator layer and the low conductivity characteristic of poly-silicon. To cover these faults, the study of new materials is urgently needed. Recently, high dielectric materials like $Al_2O_3$, $ZrO_2$ and $HfO_2$ are being studied for equivalent oxide thickness (EOT). However, poly-silicon gate is not compatible with high-k materials for gate-insulator. To integrate high-k gate dielectric materials in nano-scale devices, metal gate electrodes are expected to be used in the future. Currently, metal gate electrode materials like TiN, TaN, and WN are being widely studied for next-generation nano-scale devices. The TaN gate electrode for metal/high-k gate stack is compatible with high-k materials. According to this trend, the study about dry etching technology of the TaN film is needed. In this study, we investigated the etch mechanism of the TaN thin film in an inductively coupled plasma (ICP) system with $O_2/BCl_3/Ar$ gas chemistry. The etch rates and selectivities of TaN thin films were investigated in terms of the gas mixing ratio, the RF power, the DC-bias voltage, and the process pressure. The characteristics of the plasma were estimated using optical emission spectroscopy (OES). The surface reactions after etching were investigated using X-ray photoelectron spectroscopy (XPS) and auger electron spectroscopy (AES).

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.8
• /
• pp.875-881
• /
• 2004

Fundamental results obtained from an atomic force microscope (AFM) chemically-induced direct nano-lithography process are presented, which is regarded as a simple method for fabrication nm-scale devices such as superconducting flux flow transistors (SFFTs) and single electron tunneling transistors (SETs). Si cantilevers with Pt coating and with 30 nm thick TiO coating were used as conducting AFM tips in this study. We observed the surfaces of superconducting strip lines modified by AFM anodization' process. First, superconducting strip lines with scan size 2 ${\mu}{\textrm}{m}$${\times}$2 ${\mu}{\textrm}{m}$ have been anodized by AFM technology. The surface roughness was increased with the number of AFM scanning, The roughness variation was higher in case of the AFM tip with a positive voltage than with a negative voltage in respect of the strip surface. Second, we have patterned nm-scale oxide lines on ${YBa}-2{Cu}_3{O}_{7-x}$ superconducting microstrip surfaces by AFM conductive cantilever with a negative bias voltage. The ${YBa}-2{Cu}_3{O}_{7-x}$ oxide lines could be patterned by anodization technique. This research showed that the critical characteristics of superconducting thin films were be controlled by AFM anodization process technique. The AFM technique was expected to be used as a promising anodization technique for fabrication of an SFFT with nano-channel.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2000.02a
• /
• pp.104-104
• /
• 2000

MOS소자의 크기가 작아짐에 따라 gate 유전막의 두께 또한 얇아져야 한다. 두께가 얇아짐에 따라 gate 유전막으로써 기존의 SiO2는 direct tunneling으로 인해 높은 누설전류를 수반한다. 그래서 높은 유전상술르 가지는 물질들에 대한 연구의 필요성이 대두되고 있다. 그중 CVD-Ta2O5는 차세대 MOSFET소자기술에 있어서 높은 유전상수($\varepsilon$r+25)와 우수한 step coverage 때문에 각광을 받고 있는 물질중에 하나이다. 본 연구에서는 Ta2O5를 gate를 유전막으로 사용하고 RTN처리와 wet oxidation을 접목시켜 이들의 전기적인 특성을 향상시킬 수 있었다. p-형 wafer 위에 D2와 O2를 사용하여 SiO2(100 )를, NH3를 이용하여 Nitridation(10 )을 전처리로써 각각 실시하였고 그 위에 MOCVD방법으로 Ta2O5를 80 성장시켰다. 첫 번째 시편은 45$0^{\circ}C$ 10min동안 wet oxidation을 시켰고, 두 번째 시편은 $700^{\circ}C$ 60sec동안 NH3 분위기에서 RTN 처리를 하였다. 세 번째 시편은 동일조건으로 RTN 처리후 wet oxidation을 하였다. 그 후 각각의 시편을 capacitor를 제작하고 그 전기적 특성을 관찰하였다. Wet oxidation만을 시킨 시편은 as-deposited Ta2O5 시편에 비해서 -1.5V에서 누설전류는 약 2~3 order정도 감소되었고 accumulation 영역에서의 capacitance 값은 oxide층의 성장(5 )을 무시하면 거의 변화하지 않았다. RTN처리만 된 시편의 경우는 -1.5V에서 누설전류는 2~3order 정도 증가되었지만, accumulation 영역에서 capacitance 값은 거의 2qwork 증가하였다. 이 두가지 공정을 접목시킨 즉 RTN 처리후 wet oxidation 처리된 시편의 경우는 as-deposited Ta2O5 시편에 비해서 -1.5V에서 누설전류는 1 order 정도 감소하였고, accumulation 지역에서의 capacitance 값은 약 2배 증가하였다. 즉 as deposited Ta2O5 시편의 accumulation 지역의 capacitance 값은 12.8 fF/um2으로써 그 유효두께는 27.0 이었지만, RTN 처리후에 wet oxidation 시킨 시편의 accumulation 지역의 capacitance값은 21.2fF/um2으로써 그 유효두께는 16.3 이 되었다. 결론적으로 as deposited Ta2O5 시편에 RTN 처리후 wet oxidation을 실시한 결과 capacitance 값이 약 2배정도 증가하였고 누설전류는 약 1 order 정도 감소됨을 확인하였다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.08a
• /
• pp.288-288
• /
• 2011

최근 Charge Trap Flash (CTF) Non-Volatile Memory (NVM) 소자가 30 nm node 이하로 보고 되면서, 고집적화 플래시 메모리 소자로 각광 받고 있다. 기존의 CTF NVM 소자의 tunnel layer로 쓰이는 SiO2는 성장의 용이성과 Si 기판과의 계면특성, 낮은 누설전류와 같은 장점을 지니고 있다. 하지만 단일층의 SiO2를 tunnel layer로 사용하는 기존의 Non-Valatile Memory (NVM)는 두께가 5 nm 이하에서 direct tunneling과 Stress Induced Leakage Current (SILC) 등의 효과로 인해 게이트 누설 전류가 증가하여 메모리 보존특성의 감소와 같은 신뢰성 저하에 문제점을 지니고 있다. 이를 극복하기 위한 방안으로, 최근 CTF NVM 소자의 Tunnel Barrier Engineered (TBE) 기술이 많이 접목되고 있는 상황이다. TBE 기술은 SiO2 단일층 대신에 서로 다른 유전율을 가지는 절연막을 적층시킴으로서 전계에 대한 민감도를 높여 메모리 소자의 쓰기/지우기 동작 특성과 보존특성을 동시에 개선하는 방법이다. 또한 터널링 절연막으로 유전률이 큰 High-K 물질을 이용하면 물리적인 두께를 증가시킴으로서 누설 전류를 줄이고, 단위 면적당 gate capacitance값을 늘릴 수 있어 메모리 소자의 동작 특성을 개선할 수 있다. 본 연구에서는 CTF NVM 소자의 trap layer로 쓰이는 HfO2의 두께를 5 nm, blocking layer의 역할을 하는 Al2O3의 두께를 12 nm로 하고, tunnel layer로 Si3N4막 위에 유전율과 Energy BandGap이 유사한 HfAlO와 ZrO2를 적층하여 Program/Erase Speed, Retention, Endurance를 측정을 통해 메모리 소자로서의 특성을 비교 분석하였다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.08a
• /
• pp.53-53
• /
• 2011

This paper describes results for surface and bulk characterization of the most promising thin film solar cell material for high performance devices, (Ag,Cu) (In,Ga) Se2 (ACIGS). This material in particular exhibits a range of exotic behaviors. The surface and general materials science of the material also has direct implications for the operation of solar cells based upon it. Some of the techniques and results described will include scanning probe (AFM, STM, KPFM) measurements of epitaxial films of different surface orientations, photoelectron spectroscopy and inverse photoemission, Auger electron spectroscopy, and more. Bulk measurements are included as support for the surface measurements such as cathodoluminescence imaging around grain boundaries and showing surface recombination effects, and transmission electron microscopy to verify the surface growth behaviors to be equilibrium rather than kinetic phenomena. The results show that the polar close packed surface of CIGS is the lowest energy surface by far. This surface is expected to be reconstructed to eliminate the surface charge. However, the AgInSe2 compound has yielded excellent atomic-resolution images of the surface with no evidence of surface reconstruction. Similar imaging of CuInSe2 has proven more difficult and no atomic resolution images have been obtained, although current imaging tunneling spectroscopy images show electronic structure variations on the atomic scale. A discussion of the reasons why this may be the case is given. The surface composition and grain boundary compositions match the bulk chemistry exactly in as-grow films. However, the deposition of the heterojunction forming the device alters this chemistry, leading to a strongly n-type surface. This also directly explains unpinning of the Fermi level and the operation of the resulting devices when heterojunctions are formed with the CIGS. These results are linked to device performance through simulation of the characteristic operating behaviors of the cells using models developed in my laboratory.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.168-168
• /
• 2008

Dimension of a transistor has rapidly shrunk to increase the speed of device and to reduce the power consumption. However, it is accompanied with several problems like direct tunneling through the gate dioxide layer and low conductivity characteristic of poly-Si gate in nano-region. To cover these faults, study of new materials is urgently needed. Recently, high dielectric materials like $Al_2O_3$, $ZrO_2$, and $HfO_2$ are being studied for equivalent oxide thickness (EOT). However, poly-Si gate is not compatible with high-k materials for gate-insulator. Poly Si gate with high-k material has some problems such as gate depletion and dopant penetration problems. Therefore, new gate structure or materials that are compatible with high-k materials are also needed. TiN for metal/high-k gate stack is conductive enough to allow a good electrical connection and compatible with high-k materials. According to this trend, the study on dry etching of TiN for metal/high-k gate stack is needed. In this study, the investigations of the TiN etching characteristics were carried out using the inductively coupled $BCl_3$-based plasma system and adding $Cl_2$ gas. Dry etching of the TiN was studied by varying the etching parameters including $BCl_3$/Ar gas mixing ratio, RF power, DC-bias voltage to substrate, and $Cl_2$ gas addition. The plasmas were characterized by optical emission spectroscopy analysis. Scanning electron microscopy was used to investigate the etching profile.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.12 no.4
• /
• pp.285-294
• /
• 2010

As there are increasing number of tunneling works these days, shotcrete is used as primary supports in order to secure the stability of tunnels. The quality of shotcrete has a direct influence on tunnels, because it is a primary support which secures the stability of completed tunnels as well as the stability of tunnels under excavation. Especially in case that ordinary shotcrete is used under weak rock conditions or at water gushing sections, more shotcrete is needed and rebound ratio increases. As a result, it is hard to keep economic feasibility. In addition to it, in subway construction, there are cases of separated excavation and it may have a bad influence on construction period or quality. Therefore, in this study, we are going to evaluate the early strength of powder type accelerator.