• Journal of the Korean Society of Propulsion Engineers
• /
• v.18 no.1
• /
• pp.26-32
• /
• 2014

In this study, DC (Direct current) type steam plasma igniter is developed for effective ignition of high-energy density metal aluminum and gas temperature is measured by emission spectrum of OH radical. Because of the ultra-high gas temperature, the DC plasma jet is measured by Boltzmann plot method which is the non-contact optical technique and spectrum comparison-analysis. And both methods were applied to experiment after accurate verification. As a result, we could identify that plasma jet temperature is 2900 K ~ 5800 K in the 30 mm range from the nozzle tip.

• Geomechanics and Engineering
• /
• v.11 no.2
• /
• pp.197-209
• /
• 2016

Clayey rock has large clay mineral content. When in contact with water, this expands considerably and may present a significant hazard to the stability of the rock in geotechnical engineering applications. This is particularly important in the present work, which focused on mitigating some unwelcomed properties of clayey rock. Changes in its physical properties were simulated by subjecting the rock to a low voltage direct current (DC) using copper, steel and aluminum electrodes. The modified mechanism of the coupled electrical and chemical fields acting on the clayey rock was analyzed. It was concluded that the essence of clayey rock electrochemical modification is the electrokinetic effect of the DC field, together with the coupled hydraulic and electrical potential gradients in fine-grained clayey rock, including ion migration, electrophoresis and electro-osmosis. The aluminum cathodes were corroded and generated gibbsite at the anode; the steel and copper cathodes showed no obvious change. The electrical resistivity and uniaxial compressive strength (UCS) of the modified specimens from the anode, intermediate and cathode zones tended to decrease. Samples taken from these zones showed a positive correlation between electric resistivity and UCS.

• Journal of Environmental Science International
• /
• v.25 no.2
• /
• pp.267-280
• /
• 2016

Ground echo is radar return from stationary targets such as buildings and trees. Wind vectors from the wind profile radar in Gangneung are affected by ground echoes due to the complex mountainous terrain located to the west and the south. These ground echoes make a spurious peak close to the direct current (DC) line signal in Doppler spectra. Wind vectors polluted by ground clutters were determined from spectra of oblique beams. After eliminated the terrain echoes, the accuracy of wind vector compared with radiosonde was improved about 68.4% and its relative coefficient was increased from 0.58 to 0.97.

• Proceedings of the KIEE Conference
• /
• 2003.10b
• /
• pp.104-106
• /
• 2003

In recent years for propulsion of cooling fan in cars are more used electrical motors than the engine direct coupled type. But the electrical motor which is now used has the brush and the commutator. Because of the brush and the commutator the electrical motor has short life time, low efficiency and mechanical- electrical noise. Therefore it is tried to develope brushless dc motor. The motor is located in the hot air from the radiator. The motor temperature increases high and the increasing of the motor temperature rolls big in its character. The cooling fan motor has relative small in size and input voltage is low. For 300 w output power must be the current of the motor high which causes high copper loss. In this paper will be tested and analysed characteristics of a dc motor which is now used for cooling fan and a BLDC motor will be designed with same character of the brushed motor and with considering of improvement of the efficiency. After design the motor should be analysed and tested.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.29 no.1C
• /
• pp.59-64
• /
• 2004

We propose a new RLL(run length limited) (2,7) PP(parity preserving) code with 4 RMTR(repeated minimum transition run) for optical recording. The proposed code has better characteristics in terms of density ratio, RMTR, DC(direct current) component suppression, BER(bit error rate) and system complexity than (2,1O) code that currently applied in storage systems and (1,7) PP code that highly recommended as the next generation optical recording system. Some characteristics of the code are described with several simulations. And the proposed code's superiorites in performance is illustrated as compared with the other codes.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2008.04a
• /
• pp.869-873
• /
• 2008

Optimization method for the open loop commutation time intervals in HDD spindle start-up control is presented in this paper. A hard disk drive(HDD) uses a sensorless brushless DC motor(BLDC) for the platter rotation. Because there is no direct sensor for the rotor position, open loop commutations after sensing the rotor position at a standstill using inductive sensing method are performed to speed up the rotor up to a certain speed where the zero crossings of the back electromotive force(EMF) are measurable. Therefore successful open loop commutations are necessary for the stable start-up control of the spindle motors. Random neighborhood search(RNS) algorithm is introduced as a optimization technic in this paper. Rotor speed and its standard deviation are used as a cost function and commutation intervals obtained from the spindle motion equation are used as initial parameter values for the RNS. With the help of the proposed method optimized open loop commutation time intervals for the very low start-up current are acquired and tested. The experimental results shows that the proposed method can decrease the start-up failure rate of a HDD spindle motor.

• 제어로봇시스템학회:학술대회논문집
• /
• 1992.10a
• /
• pp.393-400
• /
• 1992

The DC(Direct-Current) servo motor has widely used for many application areas, FA(Factory Automation), OA(Office Automation) and home applications. But DC servo motor needs periodical inspection because it has brush and commutator. Recently, AC servo motor has expanded it's application areas due to for the development of the power semi-conductor and control technology. But it has large torque ripple for it's small number of commutation. And it also has cogging torque due to permanent magenet rotor. Therefore it can't run balence rotarion. Many torque ripple reduction methods are published. In this paper, phase advanced method adopted for torque ripple reduction of AC servo motor. In this research, AC servo motor torque characteristic variation surveied under the phase advance control through the computer simulation. Under the simulation, the load inertia varied from 0.0001[Kg.m$^{2}$] to 0.0314[Kg.m$^{2}$]. The result os nonlinear simulation, torque and speed ripple of AC servo motor under the phase advance control reduced approximately 50[%] and 10[%]. And maximum torque of AC servo motor under phase advance control condition increased about 5[%] as compare with fixed switching time.

• Transactions on Electrical and Electronic Materials
• /
• v.12 no.3
• /
• pp.106-109
• /
• 2011

We investigated the etching characteristics of titanium nitride (TiN) thin film in $BCl_3$/Ar inductively coupled plasma. The etching parameters were the gas mixing ratio, radio frequency (RF) power, direct current (DC)-bias voltages and process pressures. The standard conditions were as follows: total flow rate = 20 sccm, RF power = 500 W, DC-bias voltage = -100 V, substrate temperature = $40^{\circ}C$, and process pressure = 15 mTorr. The maximum etch rate of TiN thin film and the selectivity of TiN to $Al_2O_3$ thin film were 54 nm/min and 0.79. The results of X-ray photoelectron spectroscopy showed no accumulation of etch byproducts from the etched surface of TiN thin film. The TiN film etch was dominated by the chemical etching with assistance by Ar sputtering in reactive ion etching mechanism, based on the experimental results.

• Proceedings of the KIEE Conference
• /
• 2001.07a
• /
• pp.158-160
• /
• 2001

본 논문은 PSCAD/EMTDC프로그램을 이용한 제주-해남 HVDC시스템의 해석모델 개발과 해석모델을 이용한 제주-해남 HVDC시스템의 운전특성에 대한 분석 내용을 기술하였다. 제주-해남 HVDC의 안정적인 운용을 위해서는 HVDC시스템의 이해와 함께 제주교류계통의 계통특성도 같이 고려되어야 한다. 이를 위해서는 제주-해남 HVDC와 제주교류계통을 포함하는 시뮬레이션 모델을 개발하여 다양한 상황에서의 시뮬레이션을 수행하여야 한다. 본 논문에서는 AC계통과 DC 계통의 상호작용에 의한 영향 분석과 교직연계계통의 계통운용 특성에 대해서 EMTDC 제주-해남 HVDC모델과 제주 AC계통 등가축약 모델을 이용하여 분석한 결과를 설명하였다. PSCAD/EMTDC는 EMTP와 더불어 전력시스템의 과도현상 해석을 위한 신뢰성 있는 프로그램이다.

• Transactions on Electrical and Electronic Materials
• /
• v.11 no.4
• /
• pp.166-169
• /
• 2010

In this study, we changed the etch parameters (gas mixing ratio, radio frequency [RF] power, direct current [DC]-bias voltage, and process pressure) and then monitored the effect on the $HfAlO_3$ thin film etch rate and the selectivity with $SiO_2$. A maximum etch rate of 108.7 nm/min was obtained in $Cl_2$ (3 sccm)/$BCl_3$ (4 sccm)/Ar (16 sccm) plasma. The etch selectivity of $HfAlO_3$ to $SiO_2$ reached 1.11. As the RF power and the DC-bias voltage increased, the etch rate of the $HfAlO_3$ thin film increased. As the process pressure increased, the etch rate of the $HfAlO_3$ thin films increased. The chemical state of the etched surfaces was investigated with X-ray photoelectron spectroscopy. According to the results, the etching of $HfAlO_3$ thin film follows the ion-assisted chemical etching.