• Polymer(Korea)
• /
• v.35 no.5
• /
• pp.483-487
• /
• 2011

For the preparation of effective non-vascular drug eluting stent (DES), pullulan acetate (PA) was investigated as a coating material for polytetrafluorethylene (PTFE)-covered stent. PA was coated on PTFE-covered stent (PTFE-stent) by dip coating technique, and then its surface morphology, drug release behavior and cellular toxicity were tested. Field emission-scanning electron microscopy (FE-SEM) result indicated that its surface was smoother after PA coating without any cracking. The sustained release behavior of paclitaxel from PA-coated PTFE membrane was observed for 80 days. Also, the biological stability of paclitaxel in the membrane was confirmed by annexin V binding assays. Furthermore, the antitumor activity was demonstrated by an in vivo test against CT-26 murine colorectal tumors. From the results, we concluded that PA was expected as a useful coating material to design an effective non-vascular DES.

• Journal of the Korea Safety Management & Science
• /
• v.14 no.2
• /
• pp.41-48
• /
• 2012

수공구 사용시 과도한 힘은 작업성 근골격계 질환을 일으킬 수 있는 주요 원인중 하나이다. 이와 관련하여, 수공구 파지시 인체 내부에 부과되는 근력과 외적으로 작용된 힘 간의 비율을 이해하는 것이 중요하며, 이는 근육에 부과되는 과도한 힘을 최소화 시키고, 작업에 필요한 힘의 효율성을 극대화 시키는데 필수적이라 할 수 있다. 이러한 비율과 관련하여 많은 연구가 되어 왔으나, 대부분 수리적 인체역학적 모델과 같은 간접적 추정 방법에 의거하고 있는 실정이다. 이러한 인체역학적 모델을 검증하고 개선하기 위하여 해부용 팔 (cadaver)을 활용한 직접적인 근력과 악력 측정이 필수적이다. 본 연구에서는 이러한 해부용 팔을 이용하여 상지 굴근(hand flexor)을 자동으로 제어하고 근력과 함께 악력을 측정할 수 있는 Hand Motion Simulator를 개발하고, 이를 통하여 다양한 사이즈의 손잡이 파지시 요구되는 근력과 외적으로 적용된 악력을 비교함으로써 수공구 손잡이 사이즈에 따른 근력의 효율성에 대하여 측정을 해 보았다. 또한, 적용된 굴근 (FDP & FDS) 간의 힘 비율에 따른 파지법의 차이를 조사해 보았다. 내부에 주어진 근력은 외부로 작용된 악력보다 5.3배 높은 부하가 작용하였으며 이러한 수공구 손잡이 파지시 힘의 효율성 역시 FDP 와 FDS 간의 비율이 3:2 였을 때, 그리고 손잡이 크기가 작을수록 높은 결과를 보였다. 반대로 손잡이의 크기가 커질수록 힘의 효율성은 저하되었다. 또한, 손가락 관절 각도의 경우 FDP와 FDS간의 비율에 따라 상이한 자세를 나타내었다. FDP 굴근의 비율이 높을 경우 손가락 끝마디 관절 (DIP) 의 굴곡을 보였으며, FDS 굴근 비율이 높을 경우 손가락 두 번째 관절(PIP)의 굴곡을 보였다. 본 연구를 통한 결과는 추후 상지작업자에 대한 근골격계 질환 예방 기준안 마련 및 수공구 설계를 위한 기초자료로 활용이 가능할 것으로 보인다.

• Geophysics and Geophysical Exploration
• /
• v.1 no.2
• /
• pp.92-100
• /
• 1998

Array CSAMT surveys were conducted in two areas where it was not easy to identify the presence of faults only with geological survey because of thick overburden. The purpose of these surveys were to locate the faults and to delineate the deep resistivity structures around the faults. The steep dip lineaments having high contrast in resistivity laterally and the low resistive zones having some width in the resistivity sections were interpreted as faults and fracture zones associated with faults, respectively, The good applicability of array CSAMT to the investigation of fault was recognized owing to the agreement between the interpretation results of array CSAMT and the conclusive evidences collected by the following geological survey. The evidences includes the recent exposure of fault and the trajectory of fault evidences of the survey line. A comparison of the applicabilities of array CSAMT method and the resistivity method using dipole-dipole array was presented with the results of both methods along a same traverse line.

• Corrosion Science and Technology
• /
• v.16 no.1
• /
• pp.15-22
• /
• 2017

An oxidation-reduction scheme is an alternative approach for improving the galvanizability of advanced high-strength steel in the continuous hot-dip galvanizing process. Here, we investigated the effect of oxygen partial pressure ($P_{O_2}$) on the oxidation behavior of a transformation-induced plasticity steel containing 1.5 wt% Si and 1.6 wt% Mn during heating to and holding for 60 s at $700^{\circ}C$ under atmospheres with various $P_{O_2}$ values. Irrespective of $P_{O_2}$, a thin amorphous Si-rich layer of Si-Mn-O was formed underneath the Fe oxide scale (a $Fe_2O_3/Fe_3O_4$ bilayer) in the heating stage. In contrast to Si, Mn tended to segregate at the scale surface as $(Fe,Mn)_2O_3$. The multilayered structure of $(Fe,Mn)_2O_3/Fe_2O_3/Fe_3O_4$/amorphous Si-Mn-O remained even after extended oxidizing at $700^{\circ}C$ for 60 s. $Fe_2O_3$ was the dominantly growing oxide phase in the scale. The enhanced growth rate of $Fe_2O_3$ with increasing $P_{O_2}$ resulted in the formation of more Kirkendall voids in the amorphous Si-rich layer and a less Mn segregation at the scale surface. The mechanisms underlying the absence of FeO and the formation of Kirkendall voids are discussed.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.469-469
• /
• 2011

고효율 염료감응형 태양전지(DSSC, Dye-Sensitized Solar Cell)의 구현을 위해서 유용한 방법중 하나는 정렬된 기공 (pore)을 $TiO_2$막 내에 형성시키는 것이다. 메조포러스 (mesoporous) $TiO_2$막은 dip coating이나 spin coating과 같은 방법으로 주로 증착되고 있으며, P123이나 F127과 같은 amphiphilic triblock copolymer를 메조포러스 구조를 만들기 위한 뼈대로 사용하고 있다. 또한, 이렇게 생성된 구조에서 amphiphilic triblock copolymer는 열처리 공정을 통하여 쉽게 제거될 수 있다. 고효율 태양전지를 구현하는 또 다른 방법으로는 패턴 된 기판을 사용하는 것이다. 패턴 된 기판은 빛의 반사를 억제하여 흡수율을 높이는 역할을 한다. 그러나 패턴 된 기판 위에서 메조포러스 $TiO_2$막의 형성에 관한 연구는 부족한 실정이다. 본 연구에서는 spin coating 방법으로 패턴 된 Si (111) 기판 위에 메조포러스 $TiO_2$를 성장하고 그 미세구조를 분석하였다. 패턴 된 기판은 nanosphere lithography(NSL) 법으로 mask를 증착한 후 건식 식각 (dry etching) 공정을 통해서 제작되었으며, 마스크와 불순물 등 은 초음파 세척 등으로 제거되었다. 메조포러스 $TiO_2$막은 1-propanol, P123, titanium isopropoxide와 HCl을 섞어 만든 용액으로 1 cm${\times}$1 cm 기판 위에 3000 rpm과 4000 rpm으로 각각 증착하였으며, 5일 동안 4도에서 에이징한 후 350도에서 3시간 열처리하였다. 이렇게 형성한 메조포러스 막의 형상과 미세구조적 특성이 주사전자현미경(SEM, scanning electron microscope), X-선 회절(XRD, X-ray diffraction) 등을 이용하여 연구되었다. 특히, 증착 조건에 따른 메조포러스 $TiO_2$박막의 형성 기구에 관한 고찰이 진행되었다. 나아가, $TiO_2$박막과 패턴 사이에 형성되는 계면 구조에 관한 연구를 투과전자현미경을 이용하여 진행하였다.

• Bulletin of the Korean Chemical Society
• /
• v.29 no.5
• /
• pp.1038-1042
• /
• 2008

Mono and multilayer TiO2(Fe, $PEG_{600}$) films were deposited by the dip-coating on $SiO_2$/glass substrate using sol-gel method. In an attempt to improve the antibacterial properties of doped $TiO_2$ films, the influence of the iron oxides and polyethilenglycol ($PEG_{600}$) on the morphological, optical, surface chemical composition and biological properties of nanostructured layers was studied. Complementary measurements were performed including Spectroscopic Ellipsometry (SE), Scanning Electron Microscopy (SEM) coupled with the fractal analysis, X-Ray Photoelectron Spectroscopy (XPS) and antibacterial tests. It was found that different concentrations of Fe and $PEG_{600}$ added to coating solution strongly influence the porosity and morphology at nanometric scale related to fractal behaviour and the elemental and chemical states of the surfaces as well. The thermal treatment under oxidative atmosphere leads to films densification and oxides phase stabilization. The antibacterial activity of coatings against Escherichia Coli bacteria was examined by specific antibacterial tests.

• Corrosion Science and Technology
• /
• v.11 no.1
• /
• pp.9-14
• /
• 2012

The formation of the Fe-Al inhibition layer in hot-dip galvanizing is a confusing issue for a long time. This study presents a characterization result on the inhibition layer formed on C-Mn-Cr and C-Mn-Si dual-phase steels after a short time galvanizing. The samples were annealed at $800^{\circ}C$ for 60 s in $N_{2}$-10% $H_{2}$ atmosphere with a dew point of $-30^{\circ}C$, and were then galvanized in a bath containing 0.2 %Al. X-ray photoelectron spectroscopy (XPS) and transmission electron microscopy (TEM) was employed for characterization. The TEM electron diffraction shows that only $Fe_{2}Al_{5}$ intermetallic phase was formed. No orientation relationship between the $Fe_{2}Al_{5}$ phase and the steel substrate could be identified. Two peaks of Al 2p photoelectrons, one from metallic aluminum and the other from $Al^{3+}$ ions, were detected in the inhibition layer, indicating that the layer is in fact a mixture of $Fe_{2}Al_{5}$ and $Al_{2}O_{3}$. TEM/EDS analysis verifies the existence of $Al_{2}O_{3}$ in the boundaries of $Fe_{2}Al_{5}$ grains. The nucleation of $Fe_{2}Al_{5}$ and the reduction of the surface oxide probably proceeded concurrently on galvanizing, and the residual oxides prohibited the heteroepitaxial growth of $Fe_{2}Al_{5}$.

• Korean Journal of Materials Research
• /
• v.22 no.11
• /
• pp.626-630
• /
• 2012

The properties of SOFC unit cells manufactured using the decalcomania method were investigated. SOFC unit cell manufacturing using the decalcomania method is a very simple process. In order to minimize the ohmic loss of flattened tube type anode supports of solid oxide fuel cells(SOFC), the cells were fabricated by producing an anode function layer, YSZ electrolyte, LSM electrode, etc., on the supports and laminating them. The influence of these materials on the power output characteristics was studied when laminating the components and laminating the anode function layer between the anode and the electrolyte to improve the output characteristics. Regarding the performance of the SOFC unit cell, the output was 246 $mW/cm^2$ at a temperature of $800^{\circ}C$ in the case of not laminating the anode function layer; however, this value was improved by a factor of two to 574 $mW/cm^2$ due to the decrease of the ohmic resistance and polarization resistance of the cell in the case of laminating the anode function layer. The outputs appeared to be as high as 574 and 246 $mW/cm^2$ at a temperature of $800^{\circ}C$ in the case of using decalcomania paper when laminating the electrolyte layer using the in dip-coating method; however, the reason for this is that interfacial adhesion was improved due to the dense structure, which leads to a thin thickness of the electrolyte layer.

• Korean Journal of Materials Research
• /
• v.24 no.3
• /
• pp.159-165
• /
• 2014

This study is research on the thermal emissivity depending on the alignment degrees of graphite flakes. Samples were manufactured by a slurry of natural graphite flakes with organic binder and subsequent dip-coating on an aluminum substrate. The alignment degrees were controlled by applying magnetic field strength (0, 1, and 3 kG) to the coated samples. The alignment degree of the sample was measured by XRD. The thermal emissivity was measured by an infrared thermal image camera at $100^{\circ}C$. The alignment degrees were 0.04, 0.11, and 0.17 and the applied magnetic field strengths were 0, 1, and 3 kG, respectively. The thermal emissivities were 0.829, 0.837, and 0.844 and the applying magnetic field strengths were 0, 1, and 3 kG, respectively. In this study the correlation coefficient, $R^2$, between thermal emissivity and alignment degree was 0.997. Therefore, it was concluded that the thermal emissivities are correlated with the alignment degree of the graphite flakes.

• Journal of the Korean Wood Science and Technology
• /
• v.22 no.4
• /
• pp.13-18
• /
• 1994

Sapwood samples of pitch pine were treated with disodium octaborate alone by dip-diffusion, or in combination with water-repellent preservative(WRP) and methyl metacrylate(MMA). Treated samples were subjected to an accelerated leaching test for determining the improvement of leaching resistance and to soft rot and mold tests for evaluating the increase in bioefficacy, due to the addition of WRP and MMA applied as a second treatment. The addition of WRP and MMA retarded leaching of boron to some extent from treated samples and this retardation can be explained by improved water repellency of WRP and MMA treated samples. Borate /WRP and borate /MMA systems will not qualify borate treated wood for ground and fresh water contact use but may improve performance of borate treated wood in above-ground applications not subjected to continuous wetting conditions. Bioefficacy against soft rot fungi and mold fungi was improved by a second treatment with WRP. However, improvement in the performance of borate /MMA systems was not observed. Considering improvement in both resistance of leaching and bioefficacy against micro fungi by the treatment of WRP and MMA, simultaneously, the dual treatment of borate treated wood by MMA containing co-biocides might be believed as an ideal treatment system.