• Journal of Satellite, Information and Communications
• /
• v.2 no.2
• /
• pp.64-68
• /
• 2007

This paper describes the development of RF front.end equipment of a wide band high precision satellite navigation receiver to be able to receive the currently available GPS navigation signal and the GALILEO navigation signal to be developed in Europe in the near future. The wide band satellite navigation receiver with high precision performance is composed of L - band antenna, RF/IF converters for multi - band navigation signals, and high performance baseband processor. The L - band satellite navigation antenna is able to be received the signals in the range from 1.1 GHz to 1.6 GHz and from the navigation satellite positioned near the horizon. The navigation signal of GALILEO navigation satellite consists of L1, E5, and E6 band with signal bandwidth more than 20 MHz which is wider than GPS signal. Due to the wide band navigation signal, the IF frequency and signal processing speed should be increased. The RF/IF converter has been designed with the single stage downconversion structure, and the IF frequency of 140 MHz has been derived from considering the maximum signal bandwidth and the sampling frequency of 112 MHz to be used in ADC circuit. The final output of RF/IF converter is a digital IF signal which is generated from signal processing of the AD converter from the IF signal. The developed RF front - end has the C/N0 performance over 40dB - Hz for the - 130dBm input signal power and includes the automatic gain control circuits to provide the dynamic range over 40dB.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2000.05a
• /
• pp.465-469
• /
• 2000

This paper describes a single-chip full-custom implementation of pipelined adaptive decision-feedback equalizer (PADFE) using a 0.25-${\mu}{\textrm}{m}$ CMOS technology for wide-band wireless digital communication systems. To enhance the throughput rate of ADFE, two pipeline stage are inserted into the critical path of the ADFE by using delayed least-mean-square (DLMS) algorithm Redundant binary (RB) arithmetic is applied to all the data processing of the PADFE including filter taps and coefficient update blocks. When compared with conventional methods based on two's complement arithmetic, the proposed approach reduces arithmetic complexity, as well as results in a very simple complex-valued filter structure, thus suitable for VLSI implementation. The design parameters including pipeline stage, filter tap, coefficient and internal bit-width and equalization performance such as bit error rate (BER) and convergence speed are analyzed by algorithm-level simulation using COSSAP. The singl-chip PADFE contains about 205,000 transistors on an area of about 1.96$\times$1.35-$\textrm{mm}^2$. Simulation results show that it can safely operate with 200-MHz clock frequency at 2.5-V supply, and its estimated power dissipation is about 890-mW.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.16 no.1
• /
• pp.91-105
• /
• 2016

Carbon Nanotube Field-Effect Transistors (CNTFETs) have been studied as candidates for post Si CMOS owing to the better electrostatic control and high mobility. To enhance the immunity against short - channel effects (SCEs), the novel channel and gate engineered architectures have been proposed to improve CNTFETs performance. This work presents a comprehensive study of the influence of channel and gate engineering on the CNTFET switching, high frequency and circuit level performance of carbon nanotube field-effect transistors (CNTFETs). At device level, the effects of channel and gate engineering on the switching and high frequency characteristics for CNTFET have been theoretically investigated by using a quantum kinetic model. This model is based on two-dimensional non-equilibrium Green's functions (NEGF) solved self - consistently with Poisson's equations. It is revealed that hetero - material - gate and lightly doped drain and source CNTFET (HMG - LDDS - CNTFET) structure can significantly reduce leakage current, enhance control ability of the gate on channel, improve the switching speed, and is more suitable for use in low power, high frequency circuits. At circuit level, using the HSPICE with look - up table(LUT) based Verilog - A models, the impact of the channel and gate engineering on basic digital circuits (inverter, static random access memory cell) have been investigated systematically. The performance parameters of circuits have been calculated and the optimum metal gate workfunction combinations of ${\Phi}_{M1}/{\Phi}_{M2}$ have been concluded in terms of power consumption, average delay, stability, energy consumption and power - delay product (PDP). In addition, we discuss and compare the CNTFET-based circuit designs of various logic gates, including ternary and binary logic. Simulation results indicate that LDDS - HMG - CNTFET circuits with ternary logic gate design have significantly better performance in comparison with other structures.

• The Journal of Industrial Distribution & Business
• /
• v.9 no.6
• /
• pp.77-85
• /
• 2018

Purpose - The purpose of this study is to subdivide trade transaction-centered structure in a logistics/distribution industry system to apply blockchain, to establish and resolve with which types of technology, and to provide policy direction of government institution and technology to apply blockchain in this kind of industry. Research design, data, and methodology - This study was conducted with previous researches centered on cases applied in various industry sectors on the basis of blockchain technology. Results - General fields of blockchain application include digital contents distribution, IoT platform, e-Commerce, real-estate transaction, decentralized app. development(storage), certification service, smart contract, P2P network infrastructure, publication/storage of public documents, smart voting, money exchange, payment/settlement, banking security platform, actual asset storage, stock transaction and crowd funding. Blockchain is being applied in various fields home and abroad and its application cases can be explained in the banking industry, public sector, e-Commerce, medical industry, distribution and supply chain management, copyright protection. As examined in the blockchain application cases, it is expected to establish blockchain that can secure safety through distributed ledger in trade transaction because blockchain is established and applied in various sectors of industries home and abroad. Parties concerned of trade transaction can secure visibility even in interrupted specific section when they provide it as a base for distributed ledger application in trade and establish trade transaction model by applying blockchain. In case of interrupted specific section by using distributed ledger, blockchain model of trade transaction needs to be formed to make it possible for parties concerned involved in trade transaction to secure visibility and real-time tracking. Additionally, management should be possible from the time of contract until payment, freight transfer to buyers through land, air and maritime transportation. Conclusions - In order to boost blockchain-based logistics/distribution industry, the government, institutionally, needs to back up adding legal plan of shipping, logistics and distribution, reviewing standardization of electronic switching system and coming up with blockchain-based industrial road maps. In addition, the government, technologically, has to support R&D for integration with other high technology, standardization of distribution industry's blockchain technology and manpower training to expand technology development.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.12
• /
• pp.1380-1393
• /
• 2010

This paper presents a design, fabrication and the test results of planar active electronically scanned array(AESA) radar prototype for airborne fighter applications using transmit/receive(T/R) module hybrid technology. LIG Nex1 developed a AESA radar prototype to obtain key technologies for airborne fighter's radar. The AESA radar prototype consists of a radiating array, T/R modules, a RF manifold, distributed power supplies, beam controllers, compact receivers with ADC(Analog-to-Digital Converter), a liquid-cooling unit, and an appropriate structure. The AESA antenna has a 590 mm-diameter, active-element area capable of containing 536 T/R modules. Each module is located to provide a triangle grid with $14.7\;mm{\times}19.5\;mm$ spacing among T/R modules. The array dissipates 1,554 watts, with a DC input of 2,310 watts when operated at the maximum transmit duty factor. The AESA radar prototype was tested on near-field chamber and the results become equal in expected beam pattern, providing the accurate and flexible control of antenna beam steering and beam shaping.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.13 no.3
• /
• pp.184-196
• /
• 2020

In this paper, a single-bit 2nd-order delta-sigma modulator with the architecture of cascaded-of-integrator feedforward (CIFF) is proposed for precision measurement of current flowing through a secondary cell battery in a battery management system (BMS). The proposed modulator implements two switched capacitor integrators and a single-bit comparator with peripheral circuits such as a non-overlapping clock generator and a bias circuit. The proposed structure is designed to be applied to low-side current sensing method with low common mode input voltage. Using the low-side current measurement method has the advantage of reducing the burden on the circuit design. In addition, the ±30mV input voltage is resolved by the ADC with 15-bit resolution, eliminating the need for an additional programmable gain amplifier (PGA). The proposed a single-bit 2nd-order delta-sigma modulator has been implemented in a 350-nm CMOS process. It achieves 95.46-dB signal-to-noise-and-distortion ratio (SNDR), 96.01-dB spurious-free dynamic range (SFDR), and 15.56-bit effective-number-of-bits (ENOB) with an oversampling ratio (OSR) of 400 for 5-kHz bandwidth. The area and power consumption of the delta-sigma modulator are 670×490 ㎛2 and 414 ㎼, respectively.

• The Transactions of the Korea Information Processing Society
• /
• v.4 no.10
• /
• pp.2615-2628
• /
• 1997

In this paper, a new codebook design algorithm is proposed. It uses a DCT map based on two-dimensional discrete cosine of transform (2D DCT) and finite state vector quantizer (FSVQ) when the vector quantizer is designed for image transmission. We make the map by dividing input image according to edge quantity, then by the map, the significant features of training image are extracted by using the 2D DCT. A master codebook of FSVQ is generated by partitioning the training set using binary tree based on tree-structure. The state codebook is constructed from the master codebook, and then the index of input image is searched at not master codebook but state codebook. And, because the coding of index is important part for high speed digital transmission, it converts fixed length codes to variable length codes in terms of entropy coding rule. The huffman coding assigns transmission codes to codes of codebook. This paper proposes single-side growing huffman tree to speed up huffman code generation process of huffman tree. Compared with the pairwise nearest neighbor (PNN) and classified VQ (CVQ) algorithm, about Einstein and Bridge image, the new algorithm shows better picture quality with 2.04 dB and 2.48 dB differences as to PNN, 1.75 dB and 0.99 dB differences as to CVQ respectively.

• Journal of Information Technology Applications and Management
• /
• v.28 no.6
• /
• pp.69-85
• /
• 2021

In the era of the 4th Industrial Revolution, not only artificial intelligence, big data, robots, and biotechnology, but also cultural industries that require human creativity will lead. Among the cultural industries, the animation industry has high industrial utilization value due to its high connection with other industries. Among them, animation characters play the most important role as the subject leading the story of animation. In particular, the villain character not only serves as a medium for the main character to lead the story, but also captivates the audience with a different presence from the main character, adding to the fun and completeness of the animation. These characters consist of visual elements such as form and color, of which color is a tool that effectively conveys the character's personality and role to the audience, and is the first visual element to be considered in delicately describing the character's emotions and the relationship between characters. Therefore, this study attempts to analyze the color of the villain character. To this end, we will select eight Disney animations to derive the characteristics of the villain character's color by analyzing the color, value, chroma, and color association of the colors used in the Disney villain character. As a result of the analysis, the colors mainly used by Disney to convey the villain's image were red (R) and Orange (YR), and there was no difference depending on the times or animation production methods. Second, the brightness of Disney villain characters appeared to be the same medium/famous regardless of the times and production methods, and the frequency of use of high brightness was very low. In terms of saturation, the frequency of use of high and low saturation was high. Third, blackish (Bk), Strong (S), dull (Dl), and deep (Dp) tones were mainly used for tones. In particular, in recent 3D animations than previously produced 2D animations, the use of low chroma and the high black mixing rate increased. Fourth, it can be seen that Disney uses color as a visual method to more clearly express the psychology of the villain character using color association. In conclusion, the color selection of animation characters should be carefully considered as a tool to convey the character's personality, role, and emotion beyond simply using color, and the color selection of characters using color associations and symbols strengthens the narrative structure. It is hoped that this study will help analyze and select the character color of animation.

• Journal of Korean Dental Science
• /
• v.12 no.1
• /
• pp.13-19
• /
• 2019

Purpose: The aim of this study was to compare the flexural strength of provisional fixed dental prostheses which was three-dimensional (3D) printed by several build directions. Materials and Methods: A metal jig with two abutment teeth and pontic space in the middle was fabricated. This jig was scanned with a desktop scanner and provisional restoration was designed on dental computer-aided design program. On the preprocessing software, the build angles of the restorations were arranged at $0^{\circ}$, $30^{\circ}$, $45^{\circ}$, $60^{\circ}$, and $90^{\circ}$ and support was added and resultant structure was sliced to a thickness of $100{\mu}m$. Processed restorations were printed with digital light processing type 3D printer using poly methyl meta acrylate-based resin. After washing and post-curing, compressive loading was applied at a speed of 1 mm/min on a metal jig fixed to a universal testing machine. The maximum pressure at which fracture occurred was measured. For the statistical analysis, build direction was set as the independent variable and fracture strength as the dependent variable. One-way analysis of variance and Tukey's post hoc analysis was conducted to compare fracture strength among groups (${\alpha}=0.05$). Result: The mean flexural strength of provisional restoration 3D printed with the build direction of $0^{\circ}$ was $1,053{\pm}168N$; it was $1,183{\pm}188N$ at $30^{\circ}$, $1,178{\pm}81N$ at $45^{\circ}$, $1,166{\pm}133N$ at $60^{\circ}$, and $949{\pm}170N$ at $90^{\circ}$. The group with a build direction of $90^{\circ}$ showed significantly lower flexural strength than other groups (P<0.05). The flexural strength was significantly higher when the build direction was $30^{\circ}$ than when it was $90^{\circ}$ (P<0.01). Conclusion: Among the build directions $0^{\circ}$, $30^{\circ}$, $45^{\circ}$, $60^{\circ}$, and $90^{\circ}$ set for 3D printing of fixed dental prosthesis, an orientation of $30^{\circ}$ is recommended as an effective build direction for 3D printing.

• Journal of Navigation and Port Research
• /
• v.46 no.3
• /
• pp.203-208
• /
• 2022

Recently, various digital technology issues such as e-Navigation, Maritime Autonomous Surface Ship (MASS) and Smart ships have constantly emerged in the maritime industry, based on the fourth industrial revolution. The International Maritime Organization is gradually tightening regulations for marine safety and marine environmental protection, and these strengthened regulations are leading to new maritime industries. Thus, the purpose of this study was to design a suitable model to analyze the industrial competitiveness of domestic autonomous operation technology industry, based on the Porter's diamond model. Based on a total of five evaluation factors and 13 detailed factors, the industrial competitiveness of the domestic autonomous operation technology industry was evaluated qualitatively and quantitatively. This industry, which is in the early stage of industrial development, was evaluated as 16.9 points relative to indexing industrial competitiveness. Currently, it is characterized by the simultaneous development of related regulations and core technologies, from the establishment of the scope of the industry. The industrial competitiveness evaluation considering these industrial characteristics is expected to serve as the basis for strategic support and new industrial policy, and impact a wide range of related industries such as shipping, logistics, ports, and shipbuilding and equipment industries.