• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2003년도 학술회의 논문집 정보 및 제어부문 B
• /
• pp.596-599
• /
• 2003

In this paper, we designed the digital pulse motor control chip including a circular interpolation function. The proposed algorithm in this paper is a nonparametric cure generation algorithm (Jordan's algorith) and a very simple algorithm. So the design for this algorithm used a small number of gates. Also an average error is fairly low. The max output speed is 4Mpps(Pulse per second), the max input frequency is 16MHz and the chip is useful for the stepping and servo motors. The software contains one or two, and many axes linear interpolation algorithm and two axes circular interpolation algorithm.

• 수산해양기술연구
• /
• 제33권1호
• /
• pp.46-58
• /
• 1997

The energy saving is one of the most important factors for profit in marine transportation. In order to reduce the fuel oil consumtion the ship's propulsion efficiency must be increased as possible. The propulsion efficiency depends upon a combination of an engine and a propeller. The propeller has better efficiency as lower rotational speed. This situation led the engine manufacturers to design the engine that has low speed, long stroke and a small number of cylinders. Consequently, the variation of rotational torque became larger than before because of the longer delay-time in fuel oil injection process and an increased output per cylinder. As this new trends the conventional mechanical-hydrualic governors for engine speed control have been replaced by digital speed controllers which adopted the PID control or the optimal control algorithm. But these control algorithms have not enough robustness to suppress the variation of the delay-time and the parameter perturbation. In this paper we consider the delay-time and the perturbation of engine parameters as the modeling uncetainties. Next we design the robust servo controller which has zero offset in steady state engine speed, based on H sub($\infty$) control theory. The validity of the controller was investigated through the response simulation. We used a personal computer and an analog computer as the digital controller and the engine (plant) part respectively. And, we could certify that the designed controller maintains its robust servo performance even though the engine parameters may vary.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1992년도 하계학술대회 논문집 B
• /
• pp.1221-1224
• /
• 1992

To obtain a robustness which is one of important characteristics needed in servo drive, the sliding mode control method is used as a control strategy. However, the undesired phenomenon of chattering is a serious problem. In this paper, an adaptive chattering alleviation algorithm for variable structure system control is proposed to solve this serious problem. Digital controller using the theory of chattering alleviation control is applied to the position control problem of an induction motor system. Comparisons of this algorithm with other variable structure system control algorithms indicate that the chattering can be alleviated. This controller is implemented using IBM-PC(8088 CPU) which controls current controlled PWM inverter consisted of IGBT as a switching device to drive motor.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1996년도 한국자동제어학술회의논문집(국내학술편); 포항공과대학교, 포항; 24-26 Oct. 1996
• /
• pp.1450-1454
• /
• 1996

Even though digital control type high speed solenoid valve is a little inferior to analog control type servo valve and proportional control valve in performance, it is cheap and has secure performance against pollutant and simple control circuit. But high speed solenoid valve is hardly used for heavy machinery instead of servo valve or proportional control valve that is used in severe condition because the valve itself is small capacity and it shows wide dead zone during on-off control and chattering of hydraulic cylinder by chattering of pressure. It is desirable to use low-priced and strong pollutant resistant high speed solenoid valve for obtaining reliability of operation from severe working condition because it isn't necessary to acquire response characteristic of high frequency when we consider the characteristic of heavy machinery operation. In this study, PWM control algorithm for pilot pressure control of large capacity pilot operating valve will be used for precision position control of heavy machinery hydraulic cylinder. Not only cost reduction of main control valve but also high reliability of heavy machinery in severe condition can be obtained by using this pilot operating spool valve with high speed solenoid valve.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1992년도 한국자동제어학술회의논문집(국내학술편); KOEX, Seoul; 19-21 Oct. 1992
• /
• pp.1051-1059
• /
• 1992

Two types of digital repetitive control systems are analyzed and designed to reduce the error spectrum including not only harmonic but also non-harmonic components. First, a novel gain scheduling algorithm is suggested for conventional and modified repetitive controller is scheduled to reduce the infinite norm of error in frequency domain. For this, the relative error transfer function is mewly defined as the ratio of the error spectrum for the system with a repetitive controller to the error spectrum for the system with a repetitive controller to the error spectrum for the system without a repetitive controller. Secondly, as an alternative of a repetitive control system with the gain scheduling, a repetitive control system with higher order repetitve function is analyzed and designed, where instead of equal weightings, weightings of the higher order repetitive function is determined in such a way that the infinite norm of relative error transfer function is minimized. To show the validities of proposed methods, computer simulation results are illustrated for a typical disk drive head positioning servo system.

• 전력전자학회논문지
• /
• 제10권2호
• /
• pp.138-147
• /
• 2005

최근 급속도로 발전된 산업분야에서 요구되는 서보 시스템에서의 빠른 응답특성과 고도의 정밀성을 구현하기 위하여 고속의 연산을 수행할 수 있는 DSP(Digital Signal Processor)의 사용이 필수적이다. 그러나 기존의 DSP는 고속의 연산을 주력으로 전동기 제어에 필요한 PWM 게이팅 발생 장치와 엔코더 입력 장치, ADC(Analog to Digital Converter)등의 주변 장치를 포함하지 않았다. 이러한 추가적인 주변회로로 인한 제어 회로의 복잡성과 보드의 대형화 및 생산단가 상승의 요인으로 작용하였다. 따라서 본 논문에서는 연산 능력이 기존의 DSP에 뒤지지 않으며 전동기 제어 주변회로를 포함하고 있는 TMS320F2812 DSP를 사용하여 현재 산업 현장에서 사용되고 있는 SPMSM 서보 시스템을 제어하여 기존 제어기의 주변회로로 인한 문제점을 해결하고자 한다.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1991년도 한국자동제어학술회의논문집(국내학술편); KOEX, Seoul; 22-24 Oct. 1991
• /
• pp.844-849
• /
• 1991

A high speed control system for a telerobot using DSP is developed. The system is designed to resolve computational burden in advanced algorithms. The design is assumed to h ave no specific algorithm and robot configuration. The system is composed of a teaching box, a DSP board, a set of servo drivers and 16 bit microcomputer system. The teaching box is designed as a man-machine interface, which has two joysticks with three degrees of freedom for velocity generation in Cartesian space. The DSP board, i.e. DSP56000ADS based on a 10.25MIPS digital signal processor, DSP56001, computes the inverse Jacobian matrix which transforms Cartesian velocity into joint velocity. A resolved motion rate control algorithm for a 5 degrees of freedom manipulator was implemented. About 100 Hz sampling rate was achieved in this system.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1995년도 하계학술대회 논문집 B
• /
• pp.846-848
• /
• 1995

Recently, direct drive AC servo motor and DSP is widely used in the factory automation and related field due to the enhanced control and digital technology. In this paper, position control of direct drive AC servo motor and numerical interpolation algorithms are studied using DSP for the future applications. In the direct drived motor control, encoder pulse is divided into the quadruple pulse for the higher resolution and high speed pulse(10MHz) is used as reference for the slower speed motor control (M/T method). As for the general position control, PI controller is adapted for position control. In the trajectory tracking numerical algorithm, interpolation of straight line and curve algorithms are studied for the realization of path following capabilities of XY table. As for the DSP, ADSP 2105 is selected for the economy and performance points of view.

• 대한기계학회논문집
• /
• 제16권11호
• /
• pp.2011-2020
• /
• 1992

본 연구에서는 실용성을 중시하는 산업계의 요구에 부응하여 해석이 용이하면 서도 강인성을 갖춘 제어 알고리즘을 제안하여 실시간 제어가 가능한 시스템을 구축해 실험적으로 검토하였다. 매니퓰레이터와 서보계의 다이내믹스를 나타내는 미분방정 식은 선형요소와 비선형요소의 합으로 생각할 수 있다. 여기서 매니퓰레이터의 비선 형요소를 외란으로 간주해 슬라이딩 모드를 적용하므로 매니퓰레이터의 자유도가 높아 도 비교적 간단히 슬라이딩 모드의 존재 조건식으로 부터 절환 파라미터가 구해져 슬 라이딩 모드를 발생시킬 수 있는 알고리즘을 도출할 수가 있음을 보였다. 비선형요 소를 외란으로 간주하였을때 로보트 매니퓰레이터가 슬라이딩 모드에 들어갈 수 있도 록 외란에 대응하는 절환 제어입력을 종래의 방식대로 부가하면 이 제어입력으로 인해 채터링(chattering)이 증가하게 됨이 확인되었으며, 이러한 채터링을 줄일 수 있도록 새로운 절환 제어입력의 알고리즘을 도출하여 검토하였다.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2000년도 전력전자학술대회 논문집
• /
• pp.615-619
• /
• 2000

This paper presents an implementation of digital motion control system of Surface Permanent-Magnet Synchronous Motor(SPMSM) vector drives with a direct torque control(DTC) using the 16bit DSP TMS320F240 The DSP controller enable enhanced real time algorithm and cost-effective design of intelligent control for motors which can be yield enhanced operation fewer system components lower system cost increased efficiency and high performance The system presented are stator flux and torque observer of stator flux feedback model that inputs are current and voltage sensing of motor terminal and angle for a low speed operating area two hysteresis band controllers an optimal switching look-up table and IGBT voltage source inverter by using fully integrated control software. The developed control system are shown a good motion control response characteristic results and high performance features using 1.0Kw purposed servo drive SPMSM.