• 제어로봇시스템학회:학술대회논문집
• /
• 2004.08a
• /
• pp.1205-1210
• /
• 2004

The 4-20mA analog signal used in the various industrial fields to interface sensor in distributed process control has been replaced with relatively simple digital networks, called "fieldbus, and recently by Ethernet. Significant advances in Internet and computer technology have made it possible to develop an Internet based control, monitoring, and operation scheduling system for heating, ventilation and air-conditioning (HVAC) systems. The seamless integration of data networks with control networks allows access to any control point from anywhere. Field compatible field devices become so-called "smart" devices, capable of executing simple control, diagnostic and maintenance functions and providing bidirectional serial communication to higher level controller. The most important HVAC of BAS has received nationwide attention because of higher portion of more than 40% in building sector energy use and limited resources. This paper presents the Internet-based monitoring and control architecture and development of LonWorks control modules for AHU (air handling units) of HVAC in viewpoint of configuring BAS network. This article addresses issues in architecture section, electronics, embedded processors and software, and internet technologies.

• Journal of IKEEE
• /
• v.21 no.3
• /
• pp.256-259
• /
• 2017

SENT (single edge nibble transmission) is a serial communication protocol between automotive sensors and ECU (electronic control unit). SENT exploits digital waveform, so it has a simple and cheap architecture without transceiver circuits. Usually it is exploited as an embedded communication interface in the sensors. In this paper, a SENT interface was designed in Verilog HDL, fully complying with SAE J2716. It was implemented in FPGA, and verified on a test board. When it was synthesized, the gate count is about 2,500 gates in 0.18um technology.

• Proceedings of the KIEE Conference
• /
• 1998.11b
• /
• pp.484-486
• /
• 1998

In this paper, a new method for controlling the pointing device on digital display using EOG(electrooculogram) which is generated from eye movement, was suggested. The manufactured system is consisting of pre-amplifier, A/D converter, serial transmission device and PC program. The EOG is amplified by pre-amplifier. And the amplified EOG is digitized and transmitted to personal computer via rs-232c by PIC16C74A. Finally, the software for controlling the pointer on digital display is developed on computer. As the result, the error between the real subject's viewing point and the point indicated by the developed pointing device on digital display was investigated into the average value, 0.72 degree for horizontal axis, 0.96 degree for vertical axis. The pointing device developed in this study is controlled by subject's eye movement, that is, the user's intention. Furthermore, the algorithm of this study is applicable for many field such as a new method remote control, a new wheelchair control and so forth.

• Proceedings of the KIPE Conference
• /
• 2001.12a
• /
• pp.83-88
• /
• 2001

This paper deals with the economical equipment control which is used by internet network system at the industrial workplace. If the control devices can be accessed by internet, we can have the developed possibility of work conditions. In this paper, we presented the advanced digital timer which has a communication function to control and observe panel to realize control solution based on internet to be easily applicable at workplace with low cost. and we used 485 serial communication module to have parallel expansibility and safety. And, this system was experimented and designed for easy system management and status check from remote station through internet As the result of experiment, the circuit configuration would be more simplified than the existing, and it is expected that multi connection control and monitoring can be simply implemented with low cost equipment at industrial workplace.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.24 no.4
• /
• pp.1-9
• /
• 2010

An LED driving and control circuit has been developed. The LED driver has a new PWM circuit for current control of LED columns with dimming, current and thermal control, and communication functions. The PWM circuit is composed of two ring oscillator and one counter which can be constructed using basic digital logic components. In addition, it has the functions of remote control mode such as ON, OFF, emergency and power saving modes by the serial communication. The PWM generator and control circuit have been designed and fabricated 0.35[${\mu}m$] Magnachip/Hynix digital IC fabrication process. The LED driving and control board using the developed chip is fabricated and tested successfully.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 1999.05a
• /
• pp.324-329
• /
• 1999

This paper proposes new torque control of an induction motor, which is robust against time verying parameters. The control is based on adaptive vector control with serial block adaptive algorithm. Motor parameters used to estimates slip frequency and torque. Frequency mismatch in the control system detrimentally affects slip frequency estimation and torque response. In order to compensate for degradation of the responses an adaptive identifier for the magnetizing inductance and the secondary time constand is introduced. adaptive vector control system consisted of two subsystems, a vector control system realized on synchronous frame and a parameter identification system on stationary frame. the effectiveness of the proposed method was verified by some digital simulations.

• 제어로봇시스템학회:학술대회논문집
• /
• 1991.10a
• /
• pp.337-341
• /
• 1991

Fieldbus is a low level serial digital network which will be used for factory automation. This paper describes lower layer implementation of a Fieldbus network interface. Physical layer provides hardware interface between IBM-PC and Fieldbus. Also, physical layer uses manchester coding, shielded twisted pair lines and RS-485 electrical standard. Data link layer includes Intel's iDCX96 real time executive for 8797 one chip microcontroller and Fieldbus data link protocol software.

• Proceedings of the IEEK Conference
• /
• 2001.06b
• /
• pp.277-280
• /
• 2001

The proposed clock generator lowers the operating frequency in a system core though it keeps data bandwidth high because it has a multiphase clocking architecture. Moreover. it has a dual loop which is comprised of an inner analog phase generation loop and outer digital phase control loop. It has both advantages of DLL's wide operating range and DLL's low jitter The proposed design has been demonstrated in terms of the concept and Hspice simulation. All circuits were designed using a 0.25${\mu}{\textrm}{m}$ CMOS process and simulated with 2.5 V power supply.

• Progress in Superconductivity
• /
• v.2 no.1
• /
• pp.47-50
• /
• 2000

We have constructed a multi-channel SQUID magnetometer system. The system is designed to operate normally with 10 high temperature direct coupled SQUIDs. The main features of the system include a remote control by serial communication, low noise with wide bandwidth and high slew rate by several MHz modulation, signal conditioning and calibration by digital signal processing.

• Proceedings of the KIEE Conference
• /
• 1987.07b
• /
• pp.1495-1498
• /
• 1987

This paper described the design of register part, ROM and entire digital filter implementation by merging with ALU, control part last year. The register part consists of shift register, parallel load serial output register, multiplexer and selector, and we designed specially the 1024 memory cells ROM and decoder to decode the register data. Also, presented scaling algorithm to prevent the overflow.