• Journal of the Korea Institute of Military Science and Technology
• /
• v.9 no.3
• /
• pp.116-122
• /
• 2006

A fast scan digital-IF FFT receiver at the radio communication band is presented for spectrum monitoring applications. It is composed of three parts: RF front-end, fast LO board, and signal processing board. It has about 19GHz/s scan rate, multi frequency resolution from 10kHz to 2.5kHz, and high sensitivity of below -99dBm. The design and performance analysis of the digital-IF FFT receiver are presented.

• Journal of Electrical Engineering and Technology
• /
• v.9 no.2
• /
• pp.771-776
• /
• 2014

In this paper, an agile programmable chirp spread spectrum generator for wideband frequency-jamming applications from 20 MHz to 3 GHz is proposed. A frequency-mixing architecture using two voltage-controlled oscillators is used to achieve a wideband operating frequency range, and the direct digital synthesizer (DDS)-based chirping method with a two-point modulation technique is employed to provide a programmable and consistent chirp bandwidth. The proposed signal generator provides the various programmable FM signals from 20 MHz to 3 GHz with a modulation bandwidth from 0 to 400 MHz. The prototype successfully demonstrates arbitrary sequential jamming operation with a fast band-to-band hopping time of < 10 ${\mu}sec$.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.5 no.5
• /
• pp.869-876
• /
• 2001

In modern wireless communication, it has been regarded as a important problem for the spectrum efficiency to utilize the limited frequency-resource efficiently. In addition, the system architecture has been designed for low cost, low power consumption and ultra-lightweight. In this paper, we directly modulated the BCPFSK with a superior spectrum efficiency using the DDS and applied the direct conversion to the system architecture. Finally, we designed a transceiver which has the 433 MHz BCPFSK output and evaluated the system performance. In the measured result, we know that as for spectrum and the power efficiency, BCPFSK method is better than conventional one. Also, the results of the designed system is 433.92 MHz in center frequency and about 33 dBc in carrier suppression ratio. And we get the better results in local oscillator leakage and the spurious of the ISM out-band the same as -69dBc and under 60dBc.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.11 no.7
• /
• pp.1289-1295
• /
• 2007

In this paper, we implemented high-performance concurrent control system which manages whole RF systems with digital type and communicates with remote station on both wire and wireless networking. It consists of FPGA (Field Programmable Gate Array) part which controls forward/reverse LPA (Linear Power Amplifier), forward/reverse LNA (Low Noise Amplifier), channel cut wire/wireless TCP/IP, etc, master microprocessor (AVR), which manages the whole control system, Slave microprocessor which communicates SA (Spectrum Analyzer) and observes frequency spectrum of each channel with the resolution of 5KHz, 10 channel card microprocessor which independently observes each channel card and sets frequency synthesizer in channel cut and other peripherals and logics. The whole system is divided to two parts of H/W (hardware) and S/W (software) considering operational efficiency and concurrency, and implementation and cost. H/W consists of FPGA and microprocessor. We expected the optimized operation through H/W and SW co-design and hybrid H/W architecture.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.19 no.3
• /
• pp.379-386
• /
• 2016

In this paper, phase noise analysis result for 2.4 GHz PLL(phase locked loop) using SPD(sample phase detector) is proposed. It can be used for high performance frequency synthesizer's LO(local oscillator) to extend output frequency range or for LO of offset PLL to reduce a division rate or for clock signal of DDS(direct digital synthesizer). Before manufacturing, theoretical estimation of PLL's phase noise performance should be performed. In order to calculate phase noise of PLL using SPD, Leeson model is used for modeling phase noise of VCO(voltage controlled oscillator) and OCXO(ovened crystal oscillator). After theoretically analyzing phase noise of PLL, optimized loop filter bandwidth was determined. And then, phase noise of designed loop filter was calculated to find suitable OP-Amp. Also, the calculated result of phase noise was compared with the measured one. The measured phase noise of PLL was -130 dBc/Hz @ 10 kHz.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.46 no.7
• /
• pp.61-67
• /
• 2009

This paper reports an Integer-N phase locked loop (PLL) frequency synthesizer which was implemented in a 250nm standard digital CMOS process for a UHF RFID wireless communication system. The main blocks of PLL have been designed including voltage controlled oscillator, phase frequency detector, and charge pump. The LC VCO has been used for a better noise property and low-power design. The source and drain juntions of PMOS transistors are used as the varactor diodes. The ADF4111 of Analog Device has been used for the external pre-scaler and N-divider to divide VCO frequency and a third order RC filter is designed for the loop filter. The measured results show that the RF output power is -13dBm with 50$\Omega$ load, the phase noise is -91.33dBc/Hz at 100KHz offset frequency, and the maximum lock-in time is less than 600us from 930MHz to 970MHz.

• Proceedings of the KIEE Conference
• /
• 2003.11c
• /
• pp.946-949
• /
• 2003

In this paper, a DDFS(Direct Digital Frequency Synthesis)chip has been designed focusing on the reduction of ROM size and implemented using FPGA. When calculating the sine value for the input phase value, we used the Taylor series expansion approximation method to reduce the number of addresses of ROM. We also used the piecewise straight line approximation method, ie, the stored value int the ROM is the difference of the sine value and the straight line approximation. Using this method, we could reduce four bits for each ROM data.

• Proceedings of the Korea Multimedia Society Conference
• /
• 2012.05a
• /
• pp.451-451
• /
• 2012

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.2
• /
• pp.208-217
• /
• 2010

This paper presents a novel 10 GHz bio-radar system based on a frequency multiplier and phase-locked loop(PLL) for non-contact measurement of heartbeat and respiration rates. In this paper, a 2.5 GHz voltage controlled oscillator (VCO) with PLL is employed to as a frequency synthesizer, and 10 GHz continuous wave(CW) signal is generated by using frequency multiplier from 2.5 GHz signal. This paper also presents the noise characteristic of the proposed system. As a result, a better performance and economical frequency synthesizer can be achieved with the proposed bio-radar system. The experimental results shows excellent bio-signal measurement up to 100 cm without any additional digital signal processing(DSP), and the proposed system is validated.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.3
• /
• pp.321-330
• /
• 2010

In this paper, the theoretical background and the specific implementation method of a compressive receiver for RFID signal detection as well as the design method of DDL(Dispersive Delay Line) and chirp LO are described. DDL, which is one of the main components of the compressive receiver, is designed to have $13{\mu}s$ dispersive delay time and 6 MHz bandwidth using the SAW technique based on $LiNbO_3$ material. The chirp LO is designed using DDS(Direct Digital Synthesizer). Also the compressive receiver is fabricated to be installed into the RFID reader. Test results show the maximum frequency error of 25 kHz for single signal input, the receiver sensitivity of -44 dBm, and the maximum frequency error is 75 kHz for 6 multi-tone input signals. These results indicate that the fabricated compressive receiver is working well even in dense RFID operating environments.