• Journal of Power Electronics
• /
• 제8권3호
• /
• pp.201-209
• /
• 2008

This paper presents the modeling and design of a digital controller for a phase-shifted full-bridge converter (PSFBC) in a discrete-time domain. The discretized PSFBC model is first derived and then analyzed considering the sampling effect and the system parameters. Based on this model, the digital controller is directly designed in a discrete-time domain. The simulation and experimental results are provided to show the validity of the proposed modeling and controller design.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1993년도 한국자동제어학술회의논문집(국내학술편); Seoul National University, Seoul; 20-22 Oct. 1993
• /
• pp.1076-1079
• /
• 1993

A fuzzy digital controller is combined an autopilot system for compensating the cross coupling effect of the induced roll due to the dynamic characteristic of three fin torpedo. However the utilization of fuzzy chip has many interfacing problems with typical microprocessors of the guidance and control unit. Since a fuzzy digital controller on a microprocessor uses a finite word length A/D converters arul D/A converters, ADC and DAC may generate nonlinear effects such as deadband and limit cycle phenomena. In this paper, the robustness of fuzzy digital controller is tested with ADC a finite word length.

• 동력기계공학회지
• /
• 제14권1호
• /
• pp.65-70
• /
• 2010

Magnetic levitation system is nonlinear and inherently unstable, so it is difficult to control. Analog control circuit was widly used as the controller of magnetic levitation system, but digital controller is now substituted for analog controller according to development of digital electronics. In this study, Atmel AVR series, ATmega 128 which is a kind of $\mu$-processor for digital controller is used because the chip is cheap and popular. We designed and made ATmega 128 one-board controller and aimed to verify validity through the experiance of levitation response.

• 대한전기학회논문지:전력기술부문A
• /
• 제48권3호
• /
• pp.263-269
• /
• 1999

In this paper, an unifying design algorithm is presented for efficient digital implementation of continuous PID controller using general discrete orthogonal functions. The proposed algorithm is an algebraic method to determine controller parameters, which can unify controller design procedures divided into three ways. A set of linear equations for the controller design are derived from simple algebraic transformation based on general discrete orthogonal functions. By solving these equations, all of the controller parameters can be determined directly and simultaneously, which thus makes the design procedure systematic and straightforward. It does not involve any trial and error procedure, hence the difficulty of conventional approach can be avoided. The simulation results and discussions are given to demonstrate the efficiency of the proposed method.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2004년도 ICCAS
• /
• pp.232-237
• /
• 2004

In many application of DC-DC converters, loads cannot be specified in advance, i.e., their amplitudes are suddenly changed from the zero to the maximum rating. Generally, design conditions are changed for each load and then each controller is re-designed. Then, a so-called robust DC-DC converter which can cover such extensive load changes and also input voltage changes with one controller is needed. Analog control IC is used usually for the controller of DC-DC converter. Simple integral control etc. are performed with the analog control IC. However it is difficult to retain sufficient robustness of DC-DC converter by these techniques. The authors proposed the method of designing an approximate 2-degree-of-freedom (2DOF) controller of DC-AC converter. This controller has an ability to attain sufficient robustness against extensive load and DC power supply changes. For applying this approximate 2DOF controller to DC-DC converter, it is necessary to improve the degree of approximation for better robustness. In this paper, we propose a method of designing good approximate 2DOF digital controller which makes the control bandwidth wider, and at the same time makes a variation of the output voltage very small at a sudden change of resistive load. The proposed good approximate 2DOF digital controller is actually implemented on a DSP and is connected to a DC-DC converter. Experimental studies demonstrate that this type digital controller can satisfy given specifications.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2003년도 ICCAS
• /
• pp.1066-1070
• /
• 2003

Recently technologies have created new principle and theory but the PID control system remains its popularity as the PID controller contains simple structure, including maintenance and parameter adjustment being so simple. Thus, this paper proposes auto tune PID by fuzzy logic controller based on FPGA which to achieve real time and small size circuit board. The digital PID controller design to consist of analog to digital converter which use chip TDA8763AM/3 (10 bit high-speed low power ADC), digital to analog converter which use two chip DAC08 (8 bit digital to analog converters) and fuzzy logic tune digital PID processor embedded on chip FPGA XC2S50-5tq-144. The digital PID processor was designed by fundamental PID equation which architectures including multiplier, adder, subtracter and some other logic gate. The fuzzy logic tune digital PID was designed by look up table (LUT) method which data storage into ROM refer from trial and error process. The digital PID processor verified behavior by the application program ModelSimXE. The result of simulation when input is units step and vary controller gain ($K_p$, $K_i$ and $K_d$) are similarity with theory of PID and maximum execution time is 150 ns/action at frequency are 30 MHz. The fuzzy logic tune digital PID controller based on FPGA was verified by control model of level control system which can control level into model are correctly and rapidly. Finally, this design use small size circuit board and very faster than computer and microcontroller.

• Journal of Power Electronics
• /
• 제10권5호
• /
• pp.518-527
• /
• 2010

This paper presents a new technique for directly designing a linear digital controller for a single-phase pulse width modulation (PWM) converter systems, based on closed-loop identification. The design procedure consists of three steps. First, obtain a digital current controller for the inner loop system by using the error space approach, so that the power factor of the supply is close to one. The outer loop is composed of a voltage controller, a current control loop including a current controller, a PWM converter, and a capacitor. Then, all the components, except the voltage controller, are identified by a discrete-time equivalent linear model, using the closed-loop output error (CLOE) method. Based on this equivalent model, a proper digital voltage controller is then directly designed. It is shown through PSim simulations and experimental results that the proposed method is useful for the practical design of PWM converter controllers.

• Journal of Power Electronics
• /
• 제12권4호
• /
• pp.623-631
• /
• 2012

In this paper, a digital controller design procedure is presented for single-phase voltage-doubler boost rectifiers (VDBR). The model derivation of the single-phase VDBR is performed in the s-domain. After that the simplified equivalent z-domain models are derived. These z-domain models are utilized to design the input current and the output dc-link voltage controllers. For the controller design in the z-domain, the traditional K-factor method is modified by considering the nature of the digital controller. The frequency pre-warping and anti-windup techniques are adapted for the controller design. By using the proposed method, the phase margin and the control bandwidth are accurately achieved as required by controller designers in a practical frequency range. The proposed method is applied to a 2.5 kVA single-phase VDBR for Uninterruptible Power Supply (UPS) applications. From the simulation and the experimental results, the effectiveness of the proposed design method has been verified.

• 한국지능시스템학회:학술대회논문집
• /
• 한국퍼지및지능시스템학회 2003년도 ISIS 2003
• /
• pp.656-659
• /
• 2003

This paper concerns a design technique of pulse-width-modulated (PWM) controller via the digital redesign. The digital redesign is a converting technique a well-designed analog controller into the equivalent digital one maintaining the property of the original analog control system in the sense of state-matching. The redesigned digital controller is again converted into PWM controller using the equivalent area principle. An example-the altitude control or artificial satellites is included to show the effectiveness of the proposed method.

• 대한전기학회논문지:전력기술부문A
• /
• 제48권9호
• /
• pp.1131-1139
• /
• 1999

In this paper, we present a wide-bandwidth digital rebalance loop for a dynamically tuned gyroscope(DTG) based on {{{{ { H}_{2 } }}}} methodology. The operational principle and the importance of a rebalance loop are explaind, first. The augmented plant model is constructed, which includes a gyroscope model and an integrator. An {{{{ { H}_{ 2} }}}} based controller is designed for the augmented plant model. To verify the performance of the controller, a digital rebalance loop for a DTG is designed, fabricated and experimented. Through frequency response analyses and experiments using a real DTG, it is confirmed that the controller is more robustly stable and has a wider bandwidth compared with those of a conventional PID controller, contributing to the performance improvement of a DTG.