• Structural Monitoring and Maintenance
• /
• v.9 no.3
• /
• pp.271-287
• /
• 2022

This study investigates the bending behavior of a composite concrete slab roof with different methods of externally strengthing using steel plates and carbon fiber reinforced polymer (CFRP) strips. First, the concrete slab model which was reinforced with CFRP strips on the bottom surface of it is validated using experimental data, and then, using numerical modeling, 7 different models of square-shaped composite slab roofs are developed in ABAQUS software using the finite element modeling. Developed models include steel rebar reinforced concrete slab with variable thickness of CFRP and steel plates. Considering the control sample which has no external reinforcement, a set of 8 different reinforcement states has been investigated. Each of these 8 states is examined with 6 different uncertainties in terms of the properties of the materials in the construction of concrete slabs, which make 48 numerical models. In all models loading process is continued until complete failure occurs. The results from numerical investigations showed using the steel plates as an executive method for strengthening, the bending capacity of reinforced concrete slabs is increased in the ultimate bearing capacity of the slab by about 1.69 to 2.48 times. Also using CFRP strips, the increases in ultimate bearing capacity of the slab were about 1.61 to 2.36 times in different models with different material uncertainties.

• Structural Engineering and Mechanics
• /
• v.53 no.5
• /
• pp.1051-1066
• /
• 2015

The study aims on the effect of material dependency in elastic- plastic contact models by contact analysis of sphere and flat contact model and wheel rail contact model by considering the material properties without friction. The various materials are selected for the analysis based on Young's modulus and yield strength ratio (E/Y). The simulation software 'ANSYS' is employed for this study. The sphere and flat contact model is considered as a flattening model, the stress and strain for different materials are estimated. The simulation of wheel-rail contact model is also performed and the results are compared with the flattening model. The comparative study has also been extended for finding out the mean contact pressure for different materials the E/Y values between 150 and 660. The results show that the elastic-plastic contact analysis for materials up to E/Y=296.6 is depend on the nature of material properties and also for this material the mean contact pressure to yield strength reaches 2.65.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.11a
• /
• pp.527-532
• /
• 2000

The armor composite material targets such as aramid FRMLs with different type and ply number of face material and different type of back-up material, were studied to determine ballistic impact resistance and dynamic failure behavior during ballistic impact. Ballistic impact resistance is determined by $\textrm{V}_{50}$ ballistic limit, a statical velocity with 50% probability for complete penetration, test method. Also dynamic failure behaviors are respectfully observed that result from $\textrm{V}_{50}$ tests. $\textrm{V}_{50}$ tests with $0^{\circ}$ obliquity at room temperature were conducted with projectiles that were able to achieve near or complete penetration during high velocity impact tests. As a result, ballistic impact resistance of anodized Al 5052-H34 alloy(2 ply) is better than that of anodized Al 5052-H34 alloy(1 ply), but Titanium alloy showed the similar ballistic impact resistance. In the face material, ballistic impact resistance of titanium alloy is better than that of anodized Al 5052-H34 alloy. In the back-up material, ballistic impact resistance of T750 type aramid fiber is better than that of CT709 type aramid fiber.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.198-203
• /
• 2008

In the present study, the deformation behavior of both of metal and polymer combination on impact was investigated. They have showed a different deformation behavior when the co-axially combined projectile was impacted on rigid target. The theory according to Taylor's simplified approach assumes an ideally rigid-plastic material model exhibiting rate-independent behavior and simple one-dimensional wave propagation concepts that neglect radial inertia. In the case of impact with polymeric materials, elastic strain in general are not negligible compared with plastic strain; and the rigid-plastic material behavior assumed by Taylor for metallic materials cannot be applied any more. Since, the sleeve and the core materials have widely different mechanical properties, they will produce a significant difference of mechanical impedance with each other. Therefore these impedance mismatch influences on the deformation behavior sleeved polymer projectile on impact. As a result, sleeved projectiles will generate a very interesting impact behavior. Therefore, the according to sleeved metal material and core polymer material can see expected. The objective of this study was to investigate the factors which influences on deformation behavior pattern of sleeve materials surface.

• Journal of the Korea Furniture Society
• /
• v.27 no.2
• /
• pp.80-90
• /
• 2016

The idea of Sustainable, first mentioned in "Our Future (Bruntdland)" from the United Nations report released in 1987 has been highly affect design disciplines in developed countries in 21st century. It relocated industrial society and structure's attentions to nature and recourse conservation and reuse. Designed and manufactured products eventually disposed and it leads to waste of resources as well as creates environmental issues. Unfortunately, vast majority of designers starts designing without anticipation of this matter and produce more believing this leads to more sales. However shorter life of a product will create bigger increase of resource consumption and waste than, importance of re-usage and recycle will eventually increase. In modern furniture industry metal and plastics are frequently used beside wood that material has been diverse than in past. However, there are lack of plans and regulations of re-usage of those material due to difficulties of separating each different materials and collecting due to it's size. This study would like to look into recycling rate, methods and usage of three major materials (wood, metal, plastic) that is typically used in current furniture industries. Furthermore, see the potential of sustainable furniture by analyzing furniture practices made by each different recycled material from old furniture and what designers should consider to achieve feasibility of sustainable furniture.

• Korean Journal of Materials Research
• /
• v.30 no.3
• /
• pp.111-116
• /
• 2020

Two different casting speeds of 60 and 80mm/min are adopted to determine the effect of casting speed on the microstructure and mechanical properties of Al-Mg-Si/Al hybrid material prepared by duo-casting. The obtained hybrid material has a uniform and straight macro-interface between the pure Al side and the Al-Mg-Si alloy side at both casting speeds. When the casting speed is increased to 80mm/min, the size of primary α phases in Al-Mg-Si alloy decreases, without change of shape. Although the Al-Mg-Si alloy produced at higher casting speed of 80mm/min shows much higher ultimate tensile strength (UTS) and 0.2 % proof stress and lower elongation, along with higher bending strength compared to the case of the 60mm/min in casting speed, the tensile properties and bending strength of the hybrid material, which are similar to those of pure Al, are the same regardless of the increase of casting speed. Despite the different casting speeds, deformation and fracturing in hybrid materials are observed only on the pure Al side. This indicates that the macro-interface is well-bonded, allowing it to endure tensile and bending deformation in all hybrid materials.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.19 no.2
• /
• pp.202-210
• /
• 2016

The development of new concepts of liner is of great importance to effectively neutralize the enemy's attack power concealed in the protective structure or armored vehicles. A double layer liner has a combination of two different materials, one for penetration of target and the other for explosion after penetration. Therefore, it is of great importance to understand the temperature distribution before impact which should be lower than the explosive temperature of pure explosive material of the liner used. In this study, two different liner materials were obtained using cold spray coating and these material properties were characterized by DSC experiments. Numerical computations were done and the effect of temperature distribution and changes over time at each point of the explosive material depending on the layer types of the liner were discussed and analysed in the jet state.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.64 no.1
• /
• pp.91-98
• /
• 2022

Multi-layered geotextile tubes may have problems on its stability when used as cofferdam. This study presents the shear strength characteristics at the interface between geotextiles and a cementitious binder material to improve the stability of the multi-layered geotextile tubes. In this study, two different types of geotextiles are used. After mixing with a rapid setting cement, fly ash, sand, accelerator, and water, the cementitious binder material is prepared at the interface between two geotextile samples and cured under water for a desired period. The specimen is placed on upper and lower direct shear boxes by using clamping systems. A series of direct shear tests for two different geotextiles are performed along the curing time under three vertical stresses. Experimental results show that the shear strength at the interface between the cementitious binder material and geotextiles is greater than that at the interface between two geotextiles. For two types of geotextiles, apparent cohesion occurs at the interface between the cementitious binder material and geotextiles. In addition, the friction angles for any curing time are improved, compared to the interface between two geotextiles. The cementitious binder material suggested for the interface between two geotextiles may be useful for the reinforcement of multi-layered geotextile tubes.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2023.05a
• /
• pp.51-52
• /
• 2023

A new shape-stable composite phase change material (PCM) have been produced via an easy and simple vacuum impregnation method. The composite PCM have been derived from almond shell biochar (ASB) as supporting material and capric acid (CA) as phase change material. Cost effective waste almond shells (AS) are renewable, eco-friendly, and rich in pores which enhance the possibility of CA impregnation. Therefore, in this study, three different ratios of CA (1:1, 1:2 and 1:3) have been incorporated in ASB to produce shape-stabilized phase change composites (ASCAs). Different techniques such as scanning electron microscopy (SEM), Fourier transform-infrared spectroscope (FT-IR), differential scanning calorimetry (DSC), and thermogravimetric analysis (TGA) have been applied to evaluate the characteristics of ASCAs. The attained composite PCMs have exhibited shape stability with high latent heat storage, that makes it suitable for thermal energy storage applications.

• Journal of Fashion Business
• /
• v.21 no.5
• /
• pp.91-108
• /
• 2017

Interests in 3D virtual clothing technology and its application in online shopping malls are increasing with the advent of the Fourth Industrial Revolution. Most studies on 3D virtual clothing, however, are focused on observing drapes or ease of virtual clothing depending on fabric properties of representative clothing items. Therefore, the purpose of this study is: first, to determine if current input of typical material characteristics in 3D CLO are sufficient to formulate virtual skirts with different front and back silhouettes; second, to determine if subjective appearance evaluation matched physical shape characteristics of those skirts. In this study, appearances of typical cotton, wool, silk, rayon, and polyester skirts with different front and back pattern were compared between actual and virtual clothing depending on fabric materials. Subjective appearance evaluation was conducted by 7 experts regarding similarity between actual and virtual clothing with a 5-point scale. For objective evaluation of the both types of skirt shape, degree of roundness at the cross section, displacement of side seam, position of back waistline, and the number of folds at the skirt back were observed. In the case of cotton and wool, not the subjective appearance evaluation as well as shape characteristics of virtual skirts were well matched to the actual shape of skirts with a few material inputs. However, current material inputs for silk, rayon and polyester were insufficient to cover material differences in formation of virtual skirts with different front and back silhouettes.