• Korean Journal of Materials Research
• /
• v.8 no.11
• /
• pp.1067-1073
• /
• 1998

High quality diamond films of the silicon on diamond (SOD) structure are deposited using CO and $H_2$ gas mixture in microwave plasma chemical vapor deposition (CVD), a SOD structure is fabricated using low pressure CVD polysilicon on diamond/ Si(100) substrate. The crystalline structure of the diamond films which composed of { 111} and {100} planes. were changed from octahedral one to cubo-octahedron one as the CO/$H_2$ ratios are increased. The high quality diamond films without amorphous carbon and non-diamond elements were deposited at the CO/$H_2$ flow rate of 0.18. and the main phase of the diamond films shows (111) plane. The diamond/Si(lOO) structure shows that the interface is flat without voids. The measured dielectric constant. leakage current and breakdown field were $5.31\times10^{-9}A/cm^2$ and $9\times{10^7}{\Omega}cm$ respectively.

• Journal of the Korean Vacuum Society
• /
• v.21 no.4
• /
• pp.193-198
• /
• 2012

In this study, we have fabricated the polymer insulator and diamond-like carbon (DLC) thin films by using plasma enhanced chemical vapor deposition methods. we fabricated the DLC films with various thicknesses as the passivation layer on plasma polymer and investigated the structural, physical, and electrical properties of DLC/plasma polymer films. The plasma polymer synthesized in this work had the low leakage current and low dielectric constant. The values of hardness and elastic modulus in DLC/plasma polymer films are increased, and the value of rms surface roughness is decreased, and contact angle value is increased with increasing DLC film thickness. In the electrical properties of DLC/plasma polymer, the value of the dielectric constant is increased, however the leakage current property of the DLC/plasma polymer is improved than that of plasma polymer film with increasing DLC film thickness.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.07b
• /
• pp.1054-1057
• /
• 2004

The nitrogenated diamond-like carbon (NDLC) exhibits high electrical resistivity and thermal conductivity that are similar to the properties shown by diamond-like carbon (DLC) films. These diamond-like transparent properties in NDLC come in a material consisting of $sp^2$-bonded carbon versus the $sp^3$-carbon of DLC. The diamond-like properties and nondiamond-like bonding make NDLC an attractive candidate for applications. Liquid crystal (LC) alignment capabilities with ion beam exposure on NDLC thin films and electro-optical (EO) performances of the ion-beam-aligned twisted nematic liquid crystal display (TN-LCD) with oblique ion beam exposure on the NDLC thin film surface were studied. An excellent uniform alignment of the nematic liquid crystal (NLC) alignment with the ion beam exposure on the NDLC thin films was observed. In addition, it can be achieved that the good EO properties of the ion-beam-aligned TN-LCD. Finally, we will present the residual DC property of the ion-beam-aligned TN-LCD on the NDLC thin film surface.

• Journal of Mechanical Science and Technology
• /
• v.18 no.10
• /
• pp.1772-1781
• /
• 2004

The mechanical as well as tribological characteristics of coating films as thin as a few nm become more crucial as applications in micro-systems grow. Especially, the amorphous carbon film has a potential to be used as a protective layer for micro-systems. In this work, quantitative evaluation of nano-indentation, scratching, and wear tests were performed on the 7nm thick amorphous carbon film using an Atomic Force Microscope (AFM). It was shown that AFM-based nano-indentation using a diamond coated tip can be feasibly utilized for mechanical characterization of ultra-thin films. Also, it was found that the critical load where the failure of the carbon film occurred was about 18${\mu}$N by the ramp load scratch test. Finally, the wear experimental results showed that the quantitative wear rate of the carbon film ranged 10$\^$-9/～10$\^$-8/ ㎣ /N cycle. These experimental methods can be effectively utilized for a better understanding the mechanical and tribological characteristics at the nano-scale.

• Journal of the Korean institute of surface engineering
• /
• v.42 no.4
• /
• pp.173-178
• /
• 2009

DLC film was synthesized on plastic injection mold(SKD11, $30\;mm\;{\times}\;19\;mm\;{\times}\;0.5\;mm$) and Si(100) wafer for 2 h at $130^{\circ}C$ under 6 mTorr using hybrid method of rf sputtering and ion source. The obtained film was analysed by Raman spectroscopy, AFM, TEM, Nano indenter and scratch tester, etc. The film was defined as an amorphous phase. In the Raman spectrum, broad peak of $sp^2$-bonded carbon attributed to graphite at $1550\;cm^{-1}$ were observed, and the ratio of ID($sp^3$ diamond intensity)/IG($sp^2$ graphite intensity) was approximately 0.54. The adhesion of DLC film was more than 80 N with scratch tester when $0.2\;{\mu}m$ thickness Cr was coated as interlayer. The micro-hardness was distributed at 35~37 GPa. The friction coefficient was 0.02~0.07, and surface roughness(Ra) was 0.34~1.64 nm. The lifetime of DLC coated plastic injection mold using as a connector part in computer was more than 2 times of non-coated mold.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.34 no.1
• /
• pp.16-20
• /
• 2021

In this study, we tried finding new materials to improve the stain resistance properties of polymer insulating materials. Using the filtered vacuum arc source (FVAS) with a graphite target source, DLC thin films were deposited on silicon and polymer insulator substrates depending on their thickness to confirm the surface properties, physical properties, and structural properties of the thin films. Subsequently, the possibility of using a DLC thin film as a protective coating material for polymer insulators was confirmed. DLC thin films manufactured in accordance with the thickness of various thin films exhibited a very smooth and uniform surface. As the thin film thickness increased, the surface roughness value decreased and the contact angle value increased. In addition, the elastic modulus and hardness of the DLC thin film slightly increased, and the maximum values of elastic modulus and hardness were 214.5 GPa and 19.8 GPa, respectively. In addition, the DLC thin film showed a very low leakage current value, thereby exhibiting electrical insulation properties.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 1999.11a
• /
• pp.171-171
• /
• 1999

• The monthly packaging world
• /
• s.144
• /
• pp.111-113
• /
• 2005

• Proceedings of the Korean Vacuum Society Conference
• /
• 1997.02a
• /
• pp.21-21
• /
• 1997

• Proceedings of the Korean Vacuum Society Conference
• /
• 1997.02a
• /
• pp.33-33
• /
• 1997