• Journal of Power Electronics
• /
• v.16 no.4
• /
• pp.1598-1611
• /
• 2016

In some special occasions with strict size requirements, such as mine hoists, improving the design accuracy of the forced-air cooling systems of NPC three-level inverters is a key technology for improving the power density and decreasing the volume. First, a fast power-loss calculation method was brought. Its calculation principle introduced in detail, and the computation formulas were deduced. Secondly, the average and dynamic power losses of a 1MW mine hoist acting as the research target were analyzed, and a forced-air cooling system model based on a series of theoretical analyses was designed with the average power loss as a heat source. The simulation analyses proves the accuracy and effectiveness of this cooling system during the unit lifting period. Finally, according to an analysis of the periodic working condition, the maximum power-loss range of a NPC three-level inverter under multi cycle operation was obtained and its dynamic power loss was taken into the optimized cooling system model as a heat source to solve the power device damage caused by instantaneous heat accumulation. The effectiveness and feasibility of the optimization design based on the dynamic power loss calculation of the maximum power-loss range was proved by simulation and experimental results.

• Aerospace Engineering and Technology
• /
• v.1 no.1
• /
• pp.72-83
• /
• 2002

Required power and solar array sizing of KOMPSAT-2 have been analyzed by ASTRIUM and KARI in November, 2000. There are Electrical Power Subsystem(EPS) design discrepancies between ASTRIUM and Korea Aerospace Research Institute(KARI) according to heritage program, EPS operation concepts, power source and the characteristic of the electrical boxes. To design the power system of KOMPSAT-2, ASTRIUM has used the EPS design of the CHAMP and GlobalStar program. But SSTI, TOMS-EP and KOMPSAT-1's design concepts has been used for KOMPSAT-2 EPS design by the KARI. To get the design conclusion, there are many trade-off meetings for the EPS sizing using each sides' heritage program and EPS operation concept. And the EPS design factors and approaching methods have been reviewed and discussed. In addition the EPS design results from ASTRIUM and KARI are summarized in this paper.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.59 no.12
• /
• pp.2298-2305
• /
• 2010

The paper presents the Model Based Design(MBD) method which design and verify control algorithm for safety power window. Safety power window are required to work together with the anti-pinch function and have to meet FMVSS118 S5 requirements and equivalent ECC requirements. To meet the requirements, this paper presents the establishment of SILS and RCP environments. The design process can reduce time and support more performance-assured design. As a result of study, it met the regulations and achieved reaction force that close to common products.

• Journal of Power Electronics
• /
• v.4 no.3
• /
• pp.152-160
• /
• 2004

This paper presents analysis, modeling, and design of a low-harmonic, isolated, active-clamped SEPIC for future avionics applications. Simpler converter dynamics, high switching frequency, zero voltage-Transition-PWM switching, and a single-layer transformer construction result. This paper describes complete design of a digital controller for a high-frequency switching power supply. Guidelines for the minimum required resolution of the analog-to-digital converter, the pulse-width modulator, and the fixed-point computational unit is derived. A design example based on a SEPIC converter operating at the high switching frequency is presented. The controller design is based on direct digital design approach and standard root-locus techniques.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.1
• /
• pp.117-123
• /
• 2013

By calculating the spectral efficiency of symmetric balance incomplete block design(BIBD) codes satisfying BER=$10^{-9}$, it can be found that ideal BIBD code design with m=2 and various q's is effective when effective power is high($P_{sr}=-10$ dBm). But BIBD code design with q > 2 and various m's can be effective when effective power is low($P_{sr}=-25$ dBm).

• Journal of the korean Society of Automotive Engineers
• /
• v.14 no.1
• /
• pp.38-46
• /
• 1992

An optimal design technique for minimum power loss in Kopp Ball Variator Continuously Variable Transmission is developed. Kinematic analysis of traction drive contact is performed to find spin for Kopp Ball Variator, and traction force and torque are calculated from mathem atical model of traction drive contact. The objective function for optimal design is total power loss including contact loss and bearing losses. The design contraints are derived from energy balance for input and output power. The formulated optimal design problem is implemented to a non-linear programming algorithm to find minimum power loss. The performance of optimal ly designed Kopp Ball Variator shows that efficiency is increased about 5-10% compare to a commercial unit.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2018.05a
• /
• pp.37-38
• /
• 2018

BIM(Building Information Modeling) in the architecture, VDC(Virtual Design and Construction) defined CIFE(Center for Integrated Facility Engineering) of Stanford university in USA, and Data-driven design definition issued by TECDOC-1284 of IAEA are doing data-level design generated by 3D CAD technology, integrating and managing related information based on the 3D model, and Using 3D models effectively during nuclear power plant life cycle. 3D model of domestic nuclear power industry is using interference review between design fields, 4D system linked 3D construction model and schedule activity, but the 3D model generated in the design phase is effectively not utilized during the construction, operation, decommissioning. therefore, This study is aimed to suggest 3D model LOD(Level of Detail) advancement method through the analysis of existing literature, 2D drawings, and 3D models throughout nuclear power plant lifecycle.

• Journal of information and communication convergence engineering
• /
• v.7 no.2
• /
• pp.113-118
• /
• 2009

This paper is about design broadband impedance matching circuit for Coupler to improve power transfer efficiency in the power line communication (PLC) system. The Tchebycheff gain function algorithm is represented to design broadband matching circuit. A practical PLC Coupler impedance matching circuit is designed, and the characteristics for S11 and S21 of PLC coupler are enhanced comparing with unmatched one. This is done by maximizing the power transfer gain from modem to the load.

• Journal of information and communication convergence engineering
• /
• v.8 no.3
• /
• pp.258-262
• /
• 2010

This paper represents design broadband impedance matching circuit for Coupler to improve power transfer efficiency in the broadband power line communication(BPLC) systems. The Butterworth gain function equalizer is used to design broadband matching circuit. A practical PLC Coupler impedance matching circuit is designed, and the characteristics for S11 and S21 of PLC Coupler are enhanced comparing with unmatched one. This is done by maximizing the power transfer gain from modem to the load.

• Journal of IKEEE
• /
• v.12 no.1
• /
• pp.27-33
• /
• 2008

The demand of wireless communication is increased rapidly due to the development of wireless communication systems, and many people have the great interest about the "RF system". The trend of the RF audio system is to design the system with less power consumption. In this paper, we explain the Software Algorithm Design of RF systems that is suitable for low power consumption.