• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2023.05a
• /
• pp.207-208
• /
• 2023

The procedure of predicting the construction cost and selecting the best alternative is performed based on comparative review of each building case. In the case of office building, it is required continuously until design is complete, since the owner requirements are various and likely to change during the design process compared to a standardized apartment. However, since the comparison work for each alternative in practice uses only the unit construction cost, there is no correlation between the alternative and the final result, and it is difficult to quantitatively determine the effect of the determined design factor on the total construction cost. It is needed that a means to support the generation of design alternatives using similar building cases during the design phase. This paper proposes a BIM-based data replacing process to support creating and comparison of design alternatives of internal finishing for office building. When design alternatives are created through the proposed process, it is possible to compare several similar cases with current project under equivalent design circumstance. Because only some finishing properties are replaced while maintaining the shape information such as the length, height, and base constraint of the object to be replaced.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2018.11a
• /
• pp.128-129
• /
• 2018

With the increase of tall building construction, efforts for enhancing constructability are required from the pre-construction stage. Therefore, in this study, we proposed an evaluation method of constructability performance by performing construction engineering activities at the design phase. Based on some results of previous studies, we estimated the importance of design factors and categories influencing the constructability in each engineering activity related to temporary work and then presented a method for evaluating the constructability performance of design alternatives.

• Proceedings of the KIPE Conference
• /
• 2001.07a
• /
• pp.491-495
• /
• 2001

Compare with diode or thyristor bridge AC/DC converter, the 3 phase PWM converter has some merits of low THD and unit power factor. So, in many critical application like as UPS, using PWM converter is the trends. 3 phase PWM converter had been studied widely already. But analytical design procedure can not found from publication for hardware design and controller design. So, in this paper, 3 phase PWM converter analysis review was given. And from the DC analysis result, parameter design was done. From the AC model, the voltage controller and current controller was designed. The gain of controllers was calculated by analytical method.

• Journal of Institute of Control, Robotics and Systems
• /
• v.2 no.1
• /
• pp.35-44
• /
• 1996

A design method for a teleoperator robot system is presented in this paper. The control system consists of two phases; approach phase and contact one. The end-effector position of the estimated slave robot and the contact force between the end-effector and wall are displayed on the monitors at control site, using which the operator controls the teleoperator system. The approach phase controller is designed using Smith's principle and the contact one designed based upon the structured singular value ${\mu}$ in order to increase the robustness of the system. The uncertainatices such as communication time delay and the variations of system parameters are considered as a muliplicative pertubation. Computer simulations are conducted in order to evaluate the performance of the proposed design method. It is found that desirable control performance, especially in the contact phase, is obtained if the control mode is switched into contact phase when the estimated position of the slave robot end-effector is in front of the wall.

• Journal of the Korean Society for Precision Engineering
• /
• v.34 no.4
• /
• pp.265-272
• /
• 2017

Velocity ripple in manufacturing processes reduces productivity and limits the precision of the product. In practice, the frequency and phase of velocity ripples always change minutely, which makes it impossible to compensate for the ripple by simply inserting an opposite feed-forward signal in the system. In this study, an active-phase compensation algorithm was developed to enable the velocity-ripple controller to track the phase change of the ripples in real time. The proposed controller can compensate for the velocity ripple whatever its cause, including disturbance by the torque ripple. The algorithm consists of three functional modules: the velocity-ripple extractor, the synchronized integrator, and the phase shifter. Experimental results showed that the proposed controller clearly reduces velocity ripples with phase variation.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.23 no.2
• /
• pp.94-100
• /
• 2018

Generally, in a single-phase energy storage system (ESS) for households, AC ripple component with twice the fundamental frequency exists inevitably in the DC link voltage of single-phase PCS. In the grid-connected mode of a single-phase inverter, the AC ripple component in the DC link voltage causes low-order harmonics on grid-side current that deteriorates power quality on an AC grid. In this work, a control system adopting a feedforward controller is established to eliminate the AC ripple interference on the DC link side. Optimal battery nominal voltage design method is also proposed by considering the voltage loss and AC ripple voltage on DC link side in a single-phase ESS. Finally, the control system and battery nominal voltage design method are verified through simulations and experiments.

• Journal of the Korean Applied Science and Technology
• /
• v.27 no.4
• /
• pp.415-420
• /
• 2010

This study is focused on the channel design of bipolar plate in the electrode of hydrogen gas generator. The characteristics of hydrogen gas generation was studied in view of efficiency of hydrogen gas generation rate and a tendency of gas flow through the riv design of electrode. Since the flow rate and flow pattern of generated gas in the two phase flow system are the most crucial in determining the efficiency of hydrogen gas generator, we adopted the commercial analytical program of COMSOL MultiphysicsTM to calculate the theoretical flow rate of hydrogen gas from the outlet of gas generator and flow pattern of two phase fluid in the electrode. In this study, liquid electrolyte flows into the bipolar plate and decomposed into gas phase, two phase flow simulation is applied to measure the efficiency of hydrogen gas generation.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.23 no.1
• /
• pp.146-152
• /
• 2024

This paper presents the analysis and the design methods of the crossover junctions including the output phase. The general solutions were derived analytically through an even-odd analysis of the reflection coefficients and the impedance parameters for the crossover junction with arbitrary output phase. The general solutions were applied to a real crossover junction structure to derive the exact design formula for the arbitrary output phase. The results agreed well with the existing studies. The designed circuit satisfied the crossover junction operation with the exact output phase.

• Proceedings of the Korean Institute Of Construction Engineering and Management
• /
• 2007.11a
• /
• pp.531-534
• /
• 2007

In the current domestic design-build contract, design and construction are separated due to prohibition of outside work. but instead the design-build contract adopts a method of fulfilling each assignment as a joint venture, which makes it difficult for participants to communicate each other and often require changes of design. also, It is difficult to performance efficiency project that they don't want to share useful information related to design and construction. In this study suggests how to maxmize the effiency of the project by proposing a process model connected with an efficient partnering and constructability in a deign development phase of design-build constract.

• Journal of Institute of Control, Robotics and Systems
• /
• v.19 no.3
• /
• pp.195-201
• /
• 2013

In this paper, we present optimization technique for the response time of DVR (Dynamic Voltage Restorer) and the possible compensation range of voltage dip by the DVR system. To protect 3-phase phase-controlled rectifier from voltage dip, DVR system needs to have optimum response time as an important design factor. Although the fast response time of DVR ensures wider range of voltage dip, DVR controller has so high cost and poor stability. This paper proposes DVR system with optimum response time required for certain intensity of voltage dips and good stability to support possible compensation range of voltage dip. Proposed technique showed optimum response time and good stability for overall system. We believe that proposed technique is reliable and useful in DVR design.