• International Journal of Aeronautical and Space Sciences
• /
• 제17권1호
• /
• pp.29-36
• /
• 2016

Tensairity girder is a light weight inflatable fabric structural concept which can be used in road emergency transportation. It uses low pressure air to stabilize compression elements against buckling. With the purpose of obtaining the comprehensive target of minimum deflection and weight under ultimate load, the cross-section and the inner pressure of tensairity girder was optimized in this paper. The Variable Complexity Modeling (VCM) method was used in this paper combining the Kriging approximate method with the Finite Element Analysis (FEA) method, which was implemented by ABAQUS. In the Kriging method, the sample points of the surrogate model were outlined by Design of Experiment (DOE) technique based on Optimal Latin Hypercube. The optimization framework was constructed in iSIGHT with a global optimization method, Multi-Island Genetic Algorithm (MIGA), followed by a local optimization method, Sequential Quadratic Program (SQP). The result of the optimization gives a prominent conceptual design of the tensairity girder, which approves the solution architecture of VCM is feasible and efficient. Furthermore, a useful trend of sensitivity between optimization variables and responses was performed to guide future design. It was proved that the inner pressure is the key parameter to balance the maximum Von Mises stress and deflection on tensairity girder, and the parameters of cross section impact the mass of tensairity girder obviously.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회A
• /
• pp.13-19
• /
• 2008

A Wire-woven Bulk Kagome (WBK) is the new truss type cellular metal fabricated by assembling the helical wires in six directions. The WBK seems to be promising with respect to morphology, fabrication cost, and raw materials. In this paper, first, the geometric and material properties are defined as the main design parameters of the WBK considering the fact that the failure of WBK is caused by buckling of truss elements. Taguchi approach was used as statistical design of experiment(DOE) technique for optimizing the design parameters in terms of maximizing the compressive strength. Normalized specific strength is constant regardless of slenderness ratio even if material properties changed, while it increases gradually as the strainhardening coefficient decreases. Compressive strength of WBK dominantly depends on the slenderness ratio rather than one of the wire diameter, the strut length. Specifically the failure of WBK under compression by elastic buckling of struts mainly depended on the slenderness ratio and elastic modulus. However the failure of WBK by plastic failed marginally depended on the slenderness ratio, yield stress, hardening and filler metal area.

• 한국산학기술학회논문지
• /
• 제13권3호
• /
• pp.1002-1007
• /
• 2012

Pillar의 제조 방법은 진공유리 및 반도체 디스플레이 분야에서 사용되는 핵심공정 중 하나이다. Pillar는 스크린 인쇄 방식을 통하여 배치할 수 있으나 시료의 성분에 따라 메탈마스크의 패턴을 전부 통과하지 못하거나 점도에 따라 통과된 혼합물이 본래의 형상을 유지 못하는 경우가 발생한다. 본 연구에서는 알루미나와 실리카 기반의 무기화합물을 이용하여 스크린 인쇄를 통해 pillar를 배치하였다. 실험계획법의 하나인 혼합물 설계를 이용함으로써 실험횟수를 줄이고 진공유리 pillar의 조성을 설계할 수 있는 방법을 제시하고자 한다.

• 대한기계학회논문집A
• /
• 제37권3호
• /
• pp.287-294
• /
• 2013

롤투롤 인쇄전자 시스템은 높은 생산성과 낮은 원가를 이점으로 인쇄전자 산업에서 가장 각광을 받고 있는 인쇄기술 중 하나이다. 이러한 롤투롤 인쇄전자 시스템에서 인쇄패턴의 특성은 인쇄물의 기능적 성질을 결정짓는 중요한 문제라 할 수 있다. 따라서 본 연구에서는 인쇄패턴의 특성을 결정짓는 주요 인자들이 특별히 인쇄패턴의 두께와 표면 조도에 미치는 영향성에 대한 분석이 수행되었다. 실험계획법을 적용하여 인쇄패턴의 두께와 표면조도에 대한 각 인자의 주효과 및 교호작용 효과를 정량적으로 제시하였고, 분산분석을 통해 유의한 인자를 찾아내었다. 또한 이에 따르는 통계적 모델이 주요 인자의 함수로서 개발되었다. 이러한 결과는 롤투롤 전자인쇄 시스템의 특징에 따라 요구되는 인쇄패턴의 특성을 얻는데 활용될 수 있을 것이다.

• 한국기계가공학회지
• /
• 제7권4호
• /
• pp.96-101
• /
• 2008

Due to improve form accuracy and surface roughness of a aspheric lens core that is made of Ni, the study is carried out on localization about a Subminiature Optics of Proximity and Wide Field of View. The required form accuracy P-V $0.2{\mu}m$ and surface roughness is Ra 10 nm. The design of experiment(DOE) is adopted to find a optimal cutting conditions which are spindle speed, depth of cut, feedrate. Finally, the effects of this study are replacing importation and strengthening competitiveness through the localization of the Subminiature Optics of Proximity and Wide Field of View.

• 한국재료학회지
• /
• 제16권2호
• /
• pp.75-79
• /
• 2006

The effect of ozone and/or ultrasound treatments on the efficiency of slurry removal in post sliced cleaning (PSC) of silicon ingot was studied. Efficiency of slurry removal was evaluated as functions of time, temperature and surfactant with DOE (Design of Experiment) method. Residual slurries were observed on the wafer surface in case of cleaning by ozone or ultrasound separately. However, a clean wafer surface was appeared when cleaned with ozone and ultrasound simultaneously. It has found that cleaning time was the main effect among temperature, time and surfactant. Elevated temperature, addition of surfactant and high ozone concentration helped to accelerate efficient removal of slurry. The improvement of removal efficiency seems to be related to the formation of more active OH radicals. The highly cleaned surface was achieved at 10 wt% ozone, 1 min and 10 vol% surfactant with ultrasound. Application of ozone and ultrasound might be a useful method for PSC process in wafer cleaning.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2003년도 춘계학술대회 논문집
• /
• pp.116-120
• /
• 2003

To study the trafficability on soft and cohesive benthic terrain, a tracked vehicle model($670mm(L){\times}750mm(B_c)$) is designed and tested. The pitch and chevron angle of grouser, weight and center of gravity of vehicle, and drawbar pull force are chosen as experimental variables. Slip, sinkage and inclined angle of vehicle are picked as performance values. Strength of soil is considered as noise factor. A preliminary straight-line motion test is performed. Then, DOE(Design of Experiment) is discussed for further research.

• 한국수소및신에너지학회논문집
• /
• 제21권5호
• /
• pp.398-404
• /
• 2010

Process conditions for MEA fabrications have significant effects on properties and performance of the MEAs for PEMFCs. In this study, effects of additives on the surface properties of the MEA was investigated to improve homogeneity of the coated catalyst layer. Another parameter that affects on characteristics of the MEAs is hot-pressing condition. Hot pressing condition was optimized by using DOE (design of experiment) method.

• 한국가시화정보학회지
• /
• 제17권2호
• /
• pp.90-95
• /
• 2019

In the present work, the effect of flow parameters such as volume flow rate on focal point of fluidic micro lens is investigated numerically. ANSYS Fluent is used for simulations, and the flow parameters and number of simulations are determined using the space filling method of design of experiment (DOE). Having determined the location of interfaces between fluids inside the micro lens which acts as the lens curvature, a ray tracking simulation on each case is performed using COMSOL Multiphysics to determine the focal point for each lens. These data are then used to provide a relation between flow parameters and the focal point of the lens.

• 동굴
• /
• 제82호
• /
• pp.1-4
• /
• 2007

In this paper, the etching of Au films using photoresist masks on Si substrates was investigated using a capacitively coupled plasma etch reactor. The advantages of plasma etch techniques over current methods for Au metalization include the ability to simplify the metalization process flow with respect to resist lift-off schemes, and the ability to cleanly remove etched material without sidewall redeposition, as is seen in ion milling. The etch properties were measured for different gas mixing ratios of CF4/Ar, and chamber pressures while the other conditions were fixed. According to statistical design of experiment (DOE), etching process of Au films was characterized and also 20 samples were fabricated followed by measuring etch rate, selectivity and etch profile. There is a chemical reaction between CF4 and Au. Au- F is hard to remove from the surface because of its high melting point. The etching products can be sputtered by Ar ion bombardment.