• Journal of Industrial Technology
• /
• v.36
• /
• pp.57-63
• /
• 2016

In this study characteristics of debris flow landslide were investigated on the focus of debris flow disaster occurred by heavy rainfall in 2013 at Goeun-ri around Kaeryoung Mt. in Chuncheon-si. Appropriate method for estimating scale of debris flow was investigated by comparing those values from soil loss by Universal Soil Loss Equation, debris flow yield rate obtained by field survey of investigating debris flow path from initiation and erosion to deposition and other methods. As results of this study, it might be an opportunity of contributing to construct the data base for determining the size of erosion control facilities in future.

• Journal of the Korean Society of Combustion
• /
• v.7 no.2
• /
• pp.24-33
• /
• 2002

The morphology of deposits on $15-{\mu}m$ thin SiC filaments has been investigated with SEM in a co-flowing, propane/air laminar diffusion flame. The average size of mature soot particles deposited in the luminous flame edge is strongly dependent on their axial position in a typical heavily sooting flame. The surface growth of liquid-phase PAHs molecules and the transition to soots from fully-developed precursors could be observed in the radial deposition of the flame. Two sooting regimes were found: one is the transition from the condensed-phase precursors; the other is the aggregation of smaller soot particles (or chains of them) to be carried along particle path lines. In the high temperature flame edge outside the soot luminous flame surface, the very thin fiber-like structures, which are about 10 nm thick, were found.

• Journal of the Korean Ceramic Society
• /
• v.31 no.3
• /
• pp.312-320
• /
• 1994

Effect of the laser shot number on the particulates density of the pulsed laser deposited YBa2Cu3O7-x thin films and the laser irradiated surface morphology of the YBa2Cu3O7-x bulk target have been investigated. Until 100 laser shots of cumulative irradiation, the films has the particulates density of ~103 mm-2. However, after 100 laser shots, the density was increased more than 10 times. This results has been explained by the change of particulate ejection path with the development of conical structure at the target surface.

• Journal of the Semiconductor & Display Technology
• /
• v.19 no.1
• /
• pp.55-60
• /
• 2020

This study designed High impedance filter to reduce RF loss to heater heating wire and increase RF current flowing to heater ground wire. Effects such as D / R improvement and process reproducibility could be seen. In addition, RF parameter distribution optimization was possible by understanding the RF path of PE-CVD equipment using Plasma and designing filter.

• Journal of the Semiconductor & Display Technology
• /
• v.3 no.3
• /
• pp.31-35
• /
• 2004

A blue light emitting diode with 8 periods InGaN/GaN multi-quantum well structure grown by metal-organic chemical vapor deposition was fabricated with the inclusion of the metal-interconnection process in order to integrate the chips for light lamp. The quantum well structure provides the blue light photoluminescence peaked at 479.2 nm at room temperature. As decreasing the temperature to 20 K, the main peak was shifted to 469.7 nm and a minor peak at 441.9 nm appeared indicating the quantum dot formation in quantum wells. The current-voltage measurement for the fabricated LED chips shows that the metal-interconnection provides good current path with ohmic resistance of 41 $\Omega$.

• Korean Journal of Computational Design and Engineering
• /
• v.22 no.2
• /
• pp.190-201
• /
• 2017

This paper proposes how to solve a problem of FDM 3D printer's irregular output when changing volume of extrusion, adjusting movement speed of the printer's head and a way to fill new inner part. Existing slicers adjust directly to change the rotation speed of the stepper. In this method, the change of the extrusion area is delayed due to the gap between the stepper and the nozzle, so that precise control is difficult. We control the extrusion area adjusting the moving speed of the print head and making constantly the rotation speed of the stepper. Thus, the output time can be shortened by generating an efficient path having a short travel distance. For evaluation, we applied our method to lithophanes with detailed variation. Comparing existing methods, our method reduced output time at least 30%.

• Journal of the Korean institute of surface engineering
• /
• v.39 no.4
• /
• pp.147-152
• /
• 2006

Failure mechanisms of electron beam physical vapor deposited thermal barrier coatings(EB-PVD TBCs) that occur during thermal cyclic oxidation were investigated. The investigations include microstructural degradation of NiCrAIY bond coat, thermally grown oxides(TGOs) along the ceramic top coat-substrate interface and fracture path within TBCs. The microstructural degradation of the bond coat during cyclic oxidation created Al depleted zones, resulting in reduction of NiAl and ${\gamma}$-Ni solid solution phase. It was observed that the fracture took placed primarily within the TGOs or at the interfaces between TGOs and bond coat.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.12
• /
• pp.60-66
• /
• 2020

Torrential rain causes landslide damage every year. In particular, the 2011 downpour caused landslides at numerous points throughout Mt. Woomyeon, which resulted in considerable damage to people and property. Because it occurred in an urban area, this case became a major social issue and received public attention. Measures were quickly implemented for multilateral investigations and recovery. Landslides caused by heavy rain are greatly affected by rainfall at the time. Landslides from the upper part erode the flow path, increasing the size, causing much damage to the lower part. This study selected a rural village area among the damaged areas of Mt. Woomyeon, and analyzed the change in terrain profile before and after a landslide using the DSM data obtained from airborne LiDAR. This area can be divided into three hydrological basins. For each basin, the analysis was performed on the average slope of each part of the flow path, as well as the erosion and deposition due to soil flow. As a result of the analysis, it was estimated that the total amount of soil from the Jeonwon village was 15,300㎥. These field data based on GIS can be used as basic information to predict damage in the case of a similar disaster, and it can be helpful in analyzing the results of various debris flow simulations.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.34 no.3
• /
• pp.309-317
• /
• 2016

Debris flows are rapidly flowing masses of water mixed with soil and gravel from landslides which are caused by typhoons or rainstorms. The combination of Korea’s mountain dominated topography (70%) and seasonal heavy rains and typhoons causes landslides and large-scale debris flows from June to August. These phenomena often cause property damage and casualties that amount up to 20% of total annual disaster fatalities. The key point to predicting debris flow is to understand its movement mechanism, erosion, and deposition. In order to achieve a more accurate estimation of debris flow path and damage, this study incorporates quantitative analysis of high resolution LiDAR DEM (GSD 10cm) to delineate geomorphic and topographic changes induced by Jinbu real scale debris flow test.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.53-53
• /
• 2011

As the dimension of Cu interconnects has continued to reduce, its resistivity is expected to increase at the nanoscale due to increased surface and grain boundary scattering of electrons. To suppress increase of the resistivity in nanoscale interconnects, alloying Cu with other metal elements such as Al, Mn, and Ag is being considered to increase the mean free path of the drifting electrons. The formation of Al alloy with a slight amount of Cu broadly studied in the past. The study of Cu alloy including a very small Al fraction, by contrast, recently began. The formation of Cu-Al alloy is limited in wet chemical bath and was mainly conducted for fundamental studies by sputtering or evaporation system. However, these deposition methods have a limitation in production environment due to poor step coverage in nanoscale Cu metallization. In this work, gap-filling of Cu-Al alloy was conducted by cyclic MOCVD (metal organic chemical vapor deposition), followed by thermal annealing for alloying, which prevented an unwanted chemical reaction between Cu and Al precursors. To achieve filling the Cu-Al alloy into sub-100nm trench without overhang and void formation, furthermore, hydrogen plasma pretreatment of the trench pattern with Ru barrier layer was conducted in order to suppress of Cu nucleation and growth near the entrance area of the nano-scale trench by minimizing adsorption of metal precursors. As a result, superconformal gap-fill of Cu-Al alloy could be achieved successfully in the high aspect ration nanoscale trenches. Examined morphology, microstructure, chemical composition, and electrical properties of superfilled Cu-Al alloy will be discussed in detail.